Planet Technology WRT-414 User Manual

54Mbps Wireless Broadband Router
WRT-414
User’s Manual
Copyright
Copyright© 2005 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as i s". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the conte nts hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or register ed trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not ins talled and us ed in acc ordance with the instructions, ma y cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution:
To assure continued compliance.(example-use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) this Device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrol led environment. In order to avoid the possibility of exceeding the F CC radio frequency expos ure limits, human proximit y to the antenna shall not be less than 20 cm(8 inches) during normal operation.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8,2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
User’s Manual for PLANET 54Mbps Wireless Broadband Router Model: WRT-414 Rev: 1.0 (August. 2005) Part No. EM-WRT414
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION...............................................................1
1.1 PACKAGE CONTENTS ......................................................................................................................1
1. 2 FEATURES......................................................................................................................................1
1.4 SPECIFICATION................................................................................................................................1
CHAPTER 2 HARDWARE INSTALLATION......................3
2.1 HARDWARE CONNECTION...............................................................................................................3
2.2 LED INDICATORS ...........................................................................................................................4
CHAPTER 3 WEB LOGIN..............................................................................5
CHAPTER 4 QUICK SETUP.......................................................................7
4.1 TIME ZONE .....................................................................................................................................7
4.2 BROADBAND TYPE .........................................................................................................................8
4.2.1 Cable Modem....................................................................................................................9
4.2.2 Fixed-IP xDSL................................................................................................................10
4.2.3 PPPoE xDSL .................................................................................................................. 11
4.2.4 PPTP xDSL.....................................................................................................................12
4.2.5 L2TP xDSL .....................................................................................................................14
4.2.6 Telstra Big Pond.............................................................................................................16
4.2.7 Save Settings Successfully...............................................................................................16
CHAPTER 5 GENERAL SETUP..........................................................18
5.1 SYSTEM................................................................................................................................18
5.1.1 Time Zone.......................................................................................................................20
5.1.2 Password Setup...............................................................................................................21
5.1.3 Remote Management ......................................................................................................22
5.2 WAN....................................................................................................................................22
5.2.1 Dynamic IP..........................................................................................................................24
5.2.2 Static IP..........................................................................................................................25
5.2.3 PPPoE ............................................................................................................................26
5.2.4 PPTP...............................................................................................................................27
5.2.5 L2TP...............................................................................................................................28
5.2.6 Telstra Big Pond.............................................................................................................29
5.2.7 DNS ................................................................................................................................30
5.2.8 DDNS..............................................................................................................................31
5.3 LAN.....................................................................................................................................31
5.4 WIRELESS ............................................................................................................................33
5.4.1 Basic Settings..................................................................................................................34
5.4.2 Advance Settings.............................................................................................................34
5.4.3 Security...........................................................................................................................36
5.4.4 Access Control ................................................................................................................41
5.5 QOS .....................................................................................................................................41
5.5.1 Add/Edit QoS Rule..........................................................................................................42
5.6 NAT.....................................................................................................................................43
5.6.1 Port Forwarding.............................................................................................................45
5.6.2 Virtual Server..................................................................................................................46
5.6.3 Special Applications .......................................................................................................48
5.6.4 UPnP..............................................................................................................................50
5.6.5 ALG Settings...................................................................................................................51
5.7 FIREWALL.............................................................................................................................51
5.7.1 Access Control ................................................................................................................53
5.7.2 URL Blocking .................................................................................................................55
5.7.3 DoS.................................................................................................................................56
5.7.4 DMZ................................................................................................................................57
CHAPTER 6 WIRELESS CONFIGURATION...........................................................................59
6.1 AP MODE.............................................................................................................................59
6.2 STATION - AD HOC MODE ....................................................................................................61
6.3 STATION - INFRASTRUCTURE MODE .....................................................................................62
6.4 AP BRIDGE - POINT T O POINT MODE ...................................................................................63
6.5 AP BRIDGE - POINT T O MULTIPOINT MODE .........................................................................65
6.6 AP BRIDGE - WDS MODE....................................................................................................66
6.7 SECURITY SETTING OF BRIDGE MODE ...................................................................................67
CHAPTER 7 STATUS....................................................................................................................70
7.1 INTERNET CONNECTION .......................................................................................................70
7.2 DEVICE STATUS ....................................................................................................................71
7.3 SYSTEM LOG........................................................................................................................72
7.4 SECURITY LOG.....................................................................................................................72
7.5 ACTIVE DHCP CLIENT ........................................................................................................73
7.6 STATISTICS ...........................................................................................................................74
CHAPTER 8 TOOLS......................................................................................................................76
8.1 CONFIGURATION TOOLS.......................................................................................................76
8.2 FIRMWARE UPGRADE ...........................................................................................................77
8.3 RESET...................................................................................................................................79
APPENDIX A NETWORK ADAPTER INFORMA TION.......................................................80
APPENDIX B FREQUENTLY ASK QUESTION.....................................................................81
APPENDIX C GLOSSARY.........................................................................................................83

Chapter 1 Introduction

Thank you for purchasing WRT-414. This manual guides you on how to install and properly use the WRT-414 in order to take full advantage of its features.

1.1 Package Contents

Make sure that you have the following items:
One WRT-414
One AC Power Adapter
One User’s Manual CD
One Quick Installation Guide
One External Dipole Antenna
Note:
If any of the above items are missing, contact your supplier for support.

1. 2 Features

Compliant with 802.11g / 802.11b standard Allow multiple users to share a single Internet connection Internet Access via Cable or xDSL modem Access Private LAN Servers from the Public Network AP / AP Client / WDS / Bridge modes supported Equipped with four LAN ports (10/100M) and one WAN port (10/100M), Auto-MDI/MDI-X supported Support DHCP Server for easy setup System status monitoring including Active DHCP Client, Security Log and Device/Connection
Status
Easy to use Web-based GUI for configuration and management purposes
Remote Management allows configuration and upgrades from a remote site (over the Internet)
DHCP/PPPoE/PPTP/L2TP/Fixed IP allocation MAC/IP filter access control, URL blocking SPI firewall + DoS prevention protection Support UPnP function Supports 64/128-bit WEP, WPA-PSK, WPA, WPA2 Encryption to protect the wireless data
transmissions

1.4 Specification

Standard IEEE 802.11g/802.11b Compliant Signal Type DSSS (Direct Sequence Spread Spectrum) Modulation OFDM/ QPSK / BPSK / CCK
- 1 -
WAN Port 1 x 10/100Base-TX, Auto-MDI/MDI-X LAN Port 4 x 10/100Base-TX, Auto-MDI/MDI-X Antenna Dipole Antenna * 1 Data Encryption 64 bit / 128 bit WEP, WPA-PSK, WPA, WPA2 Frequency 2.4GHz - 2.484GHz Sensitivity
Data Rate Up to 54Mbps (with automatic scale back)
11g @ PER < 10%
54Mbps: -71.46 dBm 48Mbps: -73.1 dBm 36Mbps: -75 dBm 24Mbps: -77 dBm 18Mbps: -79.1 dBm 12Mbps: -81.1 dBm 9Mbps: -83.5 dBm 6Mbps: -85.52 dBm
11b @ PER < 8%
11Mbps: -82 dBm
5.5Mbps: -85.7dBm 2Mbps: -87 dBm
1Mbps: -91.5 dBm
LED Indicators PWR, WLAN
LAN: LNK/ACT * 4, 10/100Mbps * 4
WAN: LNK/ACT * 1, 10/100Mbps * 1 Power Requirement 12V DC, 1A Power Consumption TX power consumption: <650mA
RX power consumption <350mA Temperature Operating :0 ~ 55 degree C
Storage: -20 ~ 70 degree C Humidity Operating: 0 ~ 90%
Storage: 0 ~ 95% Non-Condensing Dimensions 190 x 98 x 35 mm Output Power 18dBm
- 2 -

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the WRT-414.

2.1 Hardware Connection

12V DC
RESET
1. Locate an optimum location for the WRT-414. Th e be st place for your WRT-414 is usually at the center of your wireless network, with line of sight to all of your mobile stations.
2. Adjust the antennas of WRT-414. Try to adjust them to a position that can best cover your wireless network. The antenna’s position will enhance the receiving sensitivity.
3. Connect RJ-45 cable to WRT-414 LAN port. Connect one of the LAN ports on WRT-414 to your LAN switch/hub or a computer with a RJ-45 cable.
4. Connect RJ-45 cable to WRT-414 WAN port. Connect xDSL/Cable Modem to the WAN port on WRT-414. Usually, this cable would be provided with your modem. If no cable was supplied with your modem, please use a RJ-45 Ethernet cable
5. Plug in power adapter and connect to power source. After power on, WRT-414 will start to operate.
+
WAN1234
ANT
Note: ONLY use the power adapter supplied with the WRT-414. Otherwise, the product may be
damaged. If you want to reset WRT-414 to default settings, press and hold the Reset button over 5 seconds and release. And then wait for WRT-414 restart.
Reset Button
This button has two functions: To Reboot machine without Clearing Existing Configurations:
Press the reset button with a pencil tip (for less than 5 seconds), machine will re-boot itself, the existing configurations will be kept.
To Clear All Data and restore the factory default values:
Press the reset button for longer than 5 seconds and the router will reset itself to the factory default settings (warning: your original configurations will be replaced with the factory default settings)
- 3 -

2.2 LED Indicators

LED Color STATE MEANING
On Device power on
PWR Green
WLAN Orange
10/100M Green
WAN
LNK/ACT Green
Off Device power off Blinking During boot up procedure.
Blinking Off Wireless LAN is no function
On WAN port is connected at 100Mbps Off WAN port is connected at 10Mbps
On Link is established
Blinking Packets are transmitting or receiving
Transmitting or receiving data through the Wireless LAN
LAN
10/100M Green
LNK/ACT Green
On LAN is connected to 100Mbps device Off LAN is connected to 10Mbps device On Link is established Blinking Packets are transmitting or receiving
Off LAN port is not connected
- 4 -

Chapter 3 Web Login

Web configuration provides a user-friendly graphical user interface (web pages) to manage your WRT-414. A WRT-414 with an assigned IP address will allows you to monitor and configure via web browser (e.g., MS Internet Explorer or Netscape).
1. Open your web browser.
2. Enter the IP address of your W RT-414 in the address field (default IP address is http://192.168.0.1).
3. A User Name and Password dialog box will appear. Please enter your User Name and Password here. Default User Name and Password are both “admin”. Click OK.
4. Then you will see the WRT-414 main page as below.
The left panel provides four options, Quick Setup, General Setup, Status Information and Tools.
Section Description
Quick Setup Select your Internet connection type and then input the co nfigurations needed
- 5 -
to connect to your Internet Service Provider (ISP).
General Setup This section contains configurations for the Broadband router’s advance
functions such as: Port Forwarding, Virtual Server, Access Control, Hacker Attack Prevention, DMZ, Special applications and other functions to meet your LAN requirements. You can also configure the wireless detail settings here.
Status Information
Tools This option contains Configuration tools, Firmware Upgrade and Reset
This option provides you the system information, Internet Connection, Device Status, Security Log and DHCP client Log information.
functions.
- 6 -

Chapter 4 Quick Setup

This section describes the basic configuration of the WRT-414 and allows you to connect to Internet easily.

4.1 Time Zone

The time information is used for Log entries and Firewall settings. You can keep the default Time Server address or set a new IP address for your router to synchronize its time. Click “Next” to continue.
Parameter Description
Set Time Zone Select the time zone of the country you are currently in. The router will
set its time based on your selection.
Time Server Address Remain it as default or, you can manually assign an IP address of the
Time Server. The information of Timer Server can be found in the following URL link: http://www.eecis.udel.edu/~mills/ntp/servers.html or http://www.ntp.org.
Enable Daylight Savings The router can also take Daylight savings into account. To enable this
function, check/tick the “Enable Function” box and select the which days this function will work .
Click “Next” button to proceed to the next step.
- 7 -

4.2 Broadband Type

Before establishing the Internet connection, please be sure to check with your ISP, and obtain all necessary information from them.
Broadband Description
Cable Modem ISP will automatically give you an IP address. Please refer to section
4.2.1 for details.
Fixed-IP xDSL ISP has given you a fixed IP address already. Please refer to section
4.2.2 for details.
PPPoE xDSL ISP requires you to use a Point-to-Point Protocol over Ethernet (PPPoE)
connection. Please refer to section 4.2.3 for details.
PPTP xDSL ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP)
connection. Please refer to section 4.2.4 for details.
L2TP XDSL This is not widely used. You need to know the PPTP Server address as
well as your name and password. Please refer to section 4.2.5 for details.
Telstra Big Pond This option is for Australia only. Please refer to section 4.2.6 for details.
- 8 -

4.2.1 Cable Modem

With Cable Modem connection, the ISP will automatically give you an IP address. Some ISP may also require you to fill in additional information such as Host Name and MAC address (see screen below).
Note: The Host Name and MAC address section is optional and you can skip this section if your ISP does not require these settings for you to connect to the Internet.
Parameters Description
Host Name Type in the host name provided by your ISP if any; otherwise, just leave it blank. MAC Address To connect to Internet, your ISP will require a MAC address from your PC. Type in this
MAC address in this section or use the “Clone MAC Address” button to replace the WAN port MAC address with the your PC’s. To find out the PC’s MAC address, see Appendix A. (also see Glossary for an explanation on MAC address).
When the configuration finished, click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successful ly. Please refer to section 4.2.7 for the information of this screen.
- 9 -

4.2.2 Fixed-IP xDSL

Select Fixed-IP xDSL if your ISP has given you a specified IP address. Your ISP should provide all the information required in this section.
Parameters Description
IP address assigned by your Service Provider Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0). DNS Address The IP address of ISP’s DNS (Domain Name Service) Server. Service Provider Gateway Address
Please consult your local ISP about the information above. When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.
The IP address that your ISP should provide you.
The ISP’s IP address gateway.
- 10 -
4.2.3 PPPoE xDSL
Select PPPoE if your ISP requires the PPPoE protocol for Internet connectivity. Your ISP should provide all the information like user name, password required in this section.
Parameters Description
User Name Enter the User Name provided by your ISP for the PPPoE connection. Password Enter the Password provided by your ISP for the PPPoE connection. Service Name This is an optional parameter. Leave it blank unless your ISP requires it. MTU This is an optional parameter. You can specify the maximum size of transmission
packet to the Internet. The range of the MTU will be from 512 to 1492. You can also consult you ISP for the optimal MTU as well. Default: 1392.
Connection Type
If you select “Continuous”, the router will always connect to the ISP. If the W AN line breaks down and links again, the router will auto-reconnect to the ISP. If you select “Connect On Demand”, the router will auto-connect to the ISP when a client in LAN want to use the Internet and keep connected until the WAN idle timeout. The router will close the WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface. The WAN connection will not disconnected due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP. Default: Continuous.
Idle Time You can specify an idle time threshold (minutes) for the WAN port. This means if no
- 11 -
packets have been sent (no one using the Internet) during this specified period, the router will automatically disconnect the connection from your ISP. Note: This “idle timeout” function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly, especially when your ISP charges you by time used.
When the configuration finished, click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successful ly. Please refer to section 4.2.7 for the information of this screen.

4.2.4 PPTP xDSL

Select PPTP if your ISP requires the PPTP protocol to connect to the Internet. Your ISP should provide all the information required in this section.
- 12 -
Parameter Description
Obtain an IP address Select it if the ISP requires you to obtain an IP address by DHCP automatically. Host Name Type in the host name provided by your ISP if any; otherwise, just leave it blank. MAC Address To connect to the Internet, your ISP will require a MAC address from your PC.
Type in this MAC address in this section or use the “Clone MAC Address” button to replace the WAN port MAC address with the MAC address of that PC. To find out the PC’s MAC address, see Appendix A. (also see Glossary for an
explanation on MAC address). Use the following IP address IP Address This is the IP address that your ISP has given you to establish a PPTP
Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0) Gateway Enter the IP address of the ISP’s Gateway. User ID Enter the User Name provided by your ISP for the PPTP connection.
Password Enter the Password provided by your ISP for the PPTP connection PPTP Gateway If your LAN has a PPTP gateway, enter that PPTP gateway’s IP address here. If
Connection ID This is the ID given by ISP. This is an optional parameter. MTU This is an optional parameter. You can specify the maximum size of
BEZEQ-ISRAEL Select this item if you are using the service provided by BEZEQ in Israel.
Select it if the ISP provides you a static IP to connect to the PPTP server.
connection.
Sometimes called a Connection ID.
you do not have a PPTP gateway, enter the ISP’s Gateway IP address above.
transmission packet to the Internet. The range of the MTU will be from 512 to
1492. You can also consult you ISP for the optimal MTU as well. Default: 1392
Connection Type
Idle Time You can specify an idle time threshold (minutes) for the WAN port. This means
If you select “Continuous”, the router will always connect to the ISP. If the W AN
line breaks down and links again, the router shall auto- reconnect to the ISP.
If you select “Connect On Demand”, the router will auto-connect to the ISP
when a client in LAN wants to use the Internet and keep connected until the
WAN idle timeout. The router will close the WAN connection if the time period
that no one is using the Internet exceeds the “Idle Time”.
If you select “Manual”, the router will connect to ISP only when you click
“Connect” manually from the Web user interface. The WAN connection will not
disconnected due to the idle timeout. If the WAN line breaks down and latter
links again, the router will not auto-connect to the ISP. Default: Continuous.
if no packets have been sent (no one using the Internet) throughout this
specified period, the router will automatically disconnect to with your ISP.
Note: This “idle timeout” function may not work due to abnormal activities of
- 13 -
some network application software, computer virus or hacker attacks from the
Internet. For example, some software sends network packets to the Internet in
the background, even when you are not using the Internet. So please turn off
your computer when you are not using it. This function also may not work with
some ISP. So please make sure this function can work properly, especially
when your ISP charges you by time used.
When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.
4.2.5 L2TP xDSL
Select L2TP if your ISP requires the L2TP protocol to connect to the Internet. Your ISP should provide all the information required in this section.
Parameter Description
Obtain an IP address Select it if the ISP requires you to obtain an IP address by DHCP automatically. Host Name If your ISP requires a Host Name, type in the host name provided by your ISP;
otherwise, just leave it blank. MAC Address To connect to the Internet, your ISP will require a MAC address from your PC.
Type in this MAC address in this section or use the “Clone MAC Address”
- 14 -
button to replace the WAN port MAC address with the MAC address of that PC.
To find out the PC’s MAC address, see Appendix A. (also see Glossary for an
explanation on MAC address. Use the following IP address IP Address This is the IP address that your ISP has given you to establish a L2TP
Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0) Gateway Enter the IP address of the ISP’s Gateway. User ID Enter the User Name provided by your ISP for the L2TP connection.
Password Enter the Password provided by your ISP for the L2TP connection L2TP Gateway If your LA N h as a L2T P gateway, enter that L2TP gateway’s IP address here. If
MTU This is an optional parameter. You can specify the maximum size of
Connection Type
Select it if the ISP provides you a static IP to connect to the L2TP server.
connection.
Sometimes called a Connection ID.
you do not have a L2TP gateway, enter the ISP’s Gateway IP address above.
transmission packet to the Internet. The range of the MTU will be from 1492 to
512. You can also consult you ISP for the optimal MTU as well. Default: 1392
If you select “Continuous”, the router will always connect to the ISP. If the W AN
line breaks down and links again, the router shall auto- reconnect to the ISP.
If you select “Connect On Demand”, the router will auto-connect to the ISP
when someone want to use the Internet and keep connected until the WAN idle
timeout. The router will close the WAN connection if the time period that no one
is using the Internet exceeds the “Idle Time”.
If you select “Manual”, the router will connect to ISP only when you click
“Connect” manually from the Web user interface. The WAN connection will not
disconnected due to the idle timeout. If the WAN line breaks down and latter
links again, the router will not auto-connect to the ISP. Default: Continuous. Idle Time You can specify an idle time threshold (minutes) for the WAN port. This means
if no packets have been sent (no one using the Internet) throughout this
specified period, then the router will automatically disconnect the connection
with your ISP.
Note: This “idle timeout” function may not work due to abnormal activities of
some network application software, computer virus or hacker attacks from the
Internet. For example, some software sends network packets to the Internet in
the background, even when you are not using the Internet. So please turn off
your computer when you are not using it. This function also may not work with
some ISP. So please make sure this function can work properly, especially
when your ISP charges you by time used.
- 15 -
When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.

4.2.6 Telstra Big Pond

Select Telstra Big Pond if you are live in Australia and your ISP requires this protocol to c onn ect to the Internet. Your ISP should provide all the information required in this section.
Parameters Description
User Name Enter the User Name provided by your ISP for the connection. Password Enter the Password provided by your ISP for the connection. User Decide login server manually Login Server Please enter the Login Server IP address here. When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.
If you ISP has provide the login server IP address to you, please check this box and enter the Login Server IP address below.

4.2.7 Save Settings Successfully

When you press “OK” in above configuration, the settings will be saved and the screen appears as below. Before WRT-414 restart, the settings are saved, but not function yet. You can also click “Continue” to configure other settings, this web page will appear when you save the settings in each configuration screen. Press “Apply” to restart the WRT-414 for the change to take effect immediately.
- 16 -
- 17 -

Chapter 5 General Setup

After click on the “General Setup” button at the main Page, you should see the screen below.
The General Setup contain advanced features that allow you to configure the router to meet the network’s needs such as: Wireless, Port Forwarding, Virtual Server, Access Control, URL Blocking,
Special Applications, DMZ and other functions.

5.1 System

This section shows how to setup the Broadband router ’s system Time Zone, Password and Remote Management Administrator.
- 18 -
- 19 -

5.1.1 Time Zone

The Time Zone allows WRT-414 to allocate its time on the settings configured here, it will affect log display functions such as Security Log and Firewall settings.
Parameter Description
Set Time Zone Select the time zone of the country you are currently in. The router will set its time
based on your selection.
Time Server Address You can keep the default IP address or enter a new Time Server Address for this
device to synchronize its time. You can also refer to the web site
http://www.ntp.org to find a nearest time server.
Daylight Savings The router can also take Daylight savings into account. Select the check box to
enable your daylight saving configuration. You can set the days that you wish to start and stop daylight Savings Time.
After the setup completed, please click “Apply” to save the settings. After press “Apply”, you will see a web screen to prompt you the configurations save successfully. You may refer to section 4.2.7 for the information of this screen.
- 20 -

5.1.2 Password Setup

This screen allows you to change the management password.
Parameters Description
Current Password Enter your current password for the remote management administrator to
login to your Broadband router. New Password Enter you r new password. Confirmed Password Enter your new password again for verification purposes.
After the setup completed, please click “Apply” to save the settings. After press “Apply”, you will see a web screen to prompt you the configurations save successfully. You may refer to section 4.2.7 for the information of this screen.
Note: If you forget the password, please reset the WRT-414 to the factory default by press reset button
(on WRT-414’s rear panel) over 5 seconds.
- 21 -

5.1.3 Remote Management

You can specify a Host IP address that can perform remote management from Internet.
Parameters Description
Host Address The IP address of the host on Internet that will have management / configuration
access to the Broadband router. Leave it to 0.0.0.0 means anyone can access the router’s web-based configuration from any remote location. Click the Enabled box to enable the Remote Management function. Note: When you want to access the web-based management from a remote site, you must enter the router’s WAN IP address (e.g. 10.0.0.1) into your web-browser followed by port number 8080, e.g. 10.0.0.1:8080 (see below). You’ll also need to know the password set in the Password Setting screen in order to access the management pages.
After the setup completed, please click “Apply” to save the settings. After press “Apply”, you will see a web screen to prompt you the configurations save successfully. You may refer to section 4.2.7 for the information of this screen.

5.2 WAN

The WAN Settings screen allows you to specify the type of Internet connection. The WAN settings offer the following selections for the router’s WAN port, Dynamic IP, Static IP, PPPoE, PPTP, L2TP, and
- 22 -
Loading...
+ 65 hidden pages