Planet Technology WMRT-414 User Manual

802.11g Wireless MIMO Broadband Router
WMRT-414
User’s Manual
Copyright
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as i s". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the conte nts hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or register ed trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not ins talled and us ed in acc ordance with the instructions, ma y cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution:
To assure continued compliance.(example-use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) this Device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrol led environment. In order to avoid the possibility of exceeding the F CC radio frequency expos ure limits, human proximit y to the antenna shall not be less than 20 cm(8 inches) during normal operation.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8,2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
User’s Manual for PLANET 802.11g Wireless MIMO Router Model: WMRT-414 Rev: 1.0 (December. 2005) Part No. EM-WMRT414
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION.............................................................1
1.1 PACKAGE CONTENTS ......................................................................................................................1
1. 2 FEATURES ......................................................................................................................................1
1.3 SPECIFICATION................................................................................................................................2
CHAPTER 2 HARDWARE INSTALLATION......................................3
2.1 HARDWARE CONNECTION...............................................................................................................3
2.2 LED INDICATORS............................................................................................................................4
CHAPTER 3 WEB LOGIN.....................................................................5
CHAPTER 4 QUICK SETUP .................................................................7
4.1 TIME ZONE .....................................................................................................................................7
4.2 BROADBAND TYPE .........................................................................................................................8
4.2.1 Cable Modem....................................................................................................................9
4.2.2 Fixed-IP xDSL................................................................................................................10
4.2.3 PPPoE xDSL .................................................................................................................. 11
4.2.4 PPTP xDSL.....................................................................................................................12
4.2.5 L2TP xDSL .....................................................................................................................14
4.2.6 Telstra Big Pond.............................................................................................................16
4.2.7 Save Settings Successfully...............................................................................................16
CHAPTER 5 GENERAL SETUP .........................................................18
5.1 SYSTEM................................................................................................................................19
5.1.1 Time Zone.......................................................................................................................20
5.1.2 Password Setup...............................................................................................................21
5.1.3 Remote Management ......................................................................................................22
5.2 WAN....................................................................................................................................23
5.2.1 Dynamic IP.....................................................................................................................24
5.2.2 Static IP..........................................................................................................................25
5.2.3 PPPoE ............................................................................................................................26
5.2.4 PPTP...............................................................................................................................27
5.2.5 L2TP...............................................................................................................................28
5.2.6 Telstra Big Pond.............................................................................................................29
5.2.7 DNS ................................................................................................................................30
5.2.8 DDNS..............................................................................................................................31
5.3 LAN.....................................................................................................................................32
5.4 WIRELESS ............................................................................................................................33
5.4.1 Basic Settings..................................................................................................................34
5.4.2 Advance Settings.............................................................................................................34
5.4.3 Security...........................................................................................................................35
5.4.4 Access Control ................................................................................................................41
5.5 QOS .....................................................................................................................................42
5.5.1 Add/Edit QoS Rule..........................................................................................................43
5.6 NAT.....................................................................................................................................44
5.6.1 Port Forwarding.............................................................................................................45
5.6.2 Virtual Server..................................................................................................................46
5.6.3 Special Applications .......................................................................................................48
5.6.4 UPnP..............................................................................................................................50
5.6.5 ALG Settings...................................................................................................................51
5.7 FIREWALL.............................................................................................................................51
5.7.1 Access Control ................................................................................................................53
5.7.2 URL Blocking .................................................................................................................55
5.7.3 DoS.................................................................................................................................56
5.7.4 DMZ................................................................................................................................57
CHAPTER 6 WIRELESS CONFIGURATION.......................59
6.1 AP MODE.............................................................................................................................59
6.2 AP BRIDGE - POINT TO POINT MODE....................................................................................61
6.3 AP BRIDGE - POINT TO MULTIPOINT MODE..........................................................................62
6.4 AP BRIDGE - WDS MODE....................................................................................................63
6.5 SECURITY SETTING OF BRIDGE MODE ...................................................................................64
6.5.1 WEP.....................................................................................................................................65
6.5.2 WPA-PSK.............................................................................................................................66
CHAPTER 7 STATUS................................................................67
7.1 INTERNET CONNECTION .......................................................................................................68
7.2 DEVICE STATUS ....................................................................................................................68
7.3 SYSTEM LOG........................................................................................................................69
7.4 SECURITY LOG.....................................................................................................................70
7.5 ACTIVE DHCP CLIENT.........................................................................................................71
7.6 STATISTICS ...........................................................................................................................72
CHAPTER 8 TOOLS..................................................................73
8.1 CONFIGURATION TOOLS.......................................................................................................73
8.2 FIRMWARE UPGRADE ...........................................................................................................74
8.3 RESET...................................................................................................................................75
APPENDIX A NETWORK ADAPTER INFORMA TION.......77
APPENDIX B FREQUENTL Y ASK QUESTION.....................78
APPENDIX C GLOSSARY .........................................................80

Chapter 1 Introduction

Thank you for purchasing WMRT-414. This manual guides you on how to install and properly use the WMRT-414 in order to take full advantage of its features.

1.1 Package Contents

Make sure that you have the following items:
One WMRT-414
One AC Power Adapter
One User’s Manual CD
One Quick Installation Guide
Three External Dipole Antenna
Note: If any of the above items are missing, contact your supplier for support.

1. 2 Features

z Compliant with 802.11g / 802.11b standard z Farther coverage, less dead spaces and higher throughput with MIMO technology z Supports Turbo Mode to enhance the data transfer speed within the specific wireless network (the
wireless client adapter must support Turbo mode as well)
z Supports WMM (WiFi Multi-Media) function to meet the multi-media data bandwidth requirement (the
wireless client adapter and the application must support WMM as well)
z Allow multiple users to share a single Internet connection z Internet Access via Cable or xDSL modem z Supports 64/128-bit WEP, WPA (TKIP with IEEE 802.1x), WPA2 (AES with IEEE 802.1x) functions
for high level of security
z Access Private LAN Servers from the Public Network z AP / WDS / Bridge modes supported z Equipped with four LAN ports (10/100M) and one WAN port (10/100M), Auto-MDI/MDI-X supported z Support DHCP Server for easy setup z System status monitoring including Active DHCP Client, Security Log and Device/Connection Status z Easy to use Web-based GUI for configuration and management purposes z Remote Management allows configuration and upgrades from a remote site (over the Internet) z DHCP/PPPoE/PPTP/L2TP/Fixed IP allocation z MAC/IP filter access control, URL blocking z SPI firewall + DoS prevention protection
z Support UPnP function
- 1 -

1.3 Specification

Standard IEEE 802.11g/802.11b with MIMO technology Signal Type DSSS (Direct Sequence Spread Spectrum) Modulation OFDM/ QPSK / BPSK / CCK WAN Port 1 x 10/100Base-TX, Auto-MDI/MDI-X LAN Port 4 x 10/100Base-TX, Auto-MDI/MDI-X Antenna connector 3 x RP-SMA connectors Data Encryption 64 bit / 128 bit WEP, WPA-PSK, WPA, WPA2 Frequency 2.4GHz - 2.484GHz Data Rate Up to 54Mbps (with automatic scale back) LED Indicators PWR, WLAN
LAN: LNK/ACT * 4, 10/100Mbps * 4
WAN: LNK/ACT * 1, 10/100Mbps * 1 Power Requirement 12V DC, 1A Power Consumption TX power consumption: <650mA
RX power consumption <350mA Temperature Operating :0 ~ 40 degree C
Storage: -20 ~ 70 degree C Humidity Operating: 0 ~ 90%
Storage: 0 ~ 95% Non-Condensing Dimensions 190 x 98 x 35 mm Weight 355g Output Power
18dBm±2dBm
- 2 -

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the WMRT-414.

2.1 Hardware Connection

1. Locate an optimum location for the WMRT-414. The best place for your WMRT-414 is usually
at the center of your wireless network, with line of sight to all of your mobile stations.
2. Adjust the antennas o f WMRT-414. Try to adjust them to a position that can best cover your wireless network. The antenna’s position will enhance the receiving sensitivity.
3. Connect RJ-45 cable to WMRT-414 LAN port. Connect one of the LAN ports on WMRT-414 to your LAN switch/hub or a computer with a RJ-45 cable.
4. Connect RJ-45 cable to WMRT-414 WAN port. Connect xDSL/Cable Modem to the WAN port on WMRT-414. Usually, this cable would be provided with your modem. If no cable was supplied with your modem, please use a RJ-45 Ethernet cable
5. Plug in power adapter and connect to power source. After power on, WMRT-414 will start to operate.
Note: ONLY use the power adapter supplied with the WMRT-414. Otherwise, the product may be
damaged. If you want to reset WMRT-414 to default settings, press and hold the RESET button over 10 seconds and release. And then wait for WMRT-414 restart.
RESET Button
This button has two functions: To Reboot machine without Clearing Existing Configurations:
Press the reset button with a pencil tip (for less than 5 seconds), machine will re-boot itself, the existing configurations will be kept.
To Clear All Data and restore the factory default values:
Press the reset button for longer than 10 seconds and the router will reset itself to the factory default settings (warning: your original configurations will be replaced with the factory default settings)
- 3 -

2.2 LED Indicators

LED Color STATE MEANING
On Device power on
PWR Green
WLAN Orange
10/100M Green
WAN
LNK/ACT Green
Off Device power off Blinking During boot up procedure
Blinking Off Wireless LAN is no function
On WAN port is connected at 100Mbps Off WAN port is connected at 10Mbps
On Link is established
Blinking Packets are transmitting or receiving
Transmitting or receiving data through the Wireless LAN
LAN
10/100M Green
LNK/ACT Green
On LAN is connected to 100Mbps device Off LAN is connected to 10Mbps device On Link is established Blinking Packets are transmitting or receiving
Off LAN port is not connected
- 4 -

Chapter 3 Web Login

A WMRT-414 with an assigned IP address allows you to monitor and configure via web browser (e.g., MS Internet Explorer or Netscape).
1. Open your web browser.
2. Enter the IP address of your WMRT-414 in the address field (default IP address is
http://192.168.0.1).
3. A User Name and Password dialog box will appear. Please enter your User Name and Password here. Default User Name and Password are both “admin”. Click OK.
4. Then you will see the WMRT-414 HOME screen as below.
The left panel provides four options, Quick Setup, General Setup, Status Information and Tools.
- 5 -
Section Description
Quick Setup Select your Internet connection type and then input the co nfigurations needed
to connect to your Internet Service Provider (ISP).
General Setup This section contains configurations for the Broadband router’s advance
functions such as: Port Forwarding, Virtual Server, Access Control, Hacker Attack Prevention, DMZ, Special applications and other functions to meet your LAN requirements. You can a lso configure the wireless detail settings here.
Status Info
Tools This option contains Configuration tools, Firmware Upgrade and Reset
This option provides you the system information, Internet Connection, Device Status, Security Log and DHCP client Log information.
functions.
- 6 -

Chapter 4 Quick Setup

This section describes the basic configuration of the WMRT-414 and allows you to connect to Internet easily.

4.1 Time Zone

The time information is used for Log entries and Firewall settings. You can keep the default Time Server address or set a new IP address for your router to synchronize its time. Click “Next” to continue.
Parameter Description
Set Time Zone Select the time zone of the country you are currently in. The router will
set its time based on your selection.
Time Server Address Remain it as default or, you can manually assign an IP address of the
Time Server. The information of Timer Server can be found in the following URL link: http://www.eecis.udel.edu/~mills/ntp/servers.html or http://www.ntp.org.
Enable Dayl ight Savings The router can also take Daylight savings into account. To enable this
function, check/tick the “Enable Function” box and select which days this function will work.
Click “Next” button to proceed to the next step.
- 7 -

4.2 Broadband Type

Before establishing the Internet connection, please be sure to check with your ISP, and obtain all necessary information from them.
Broadband Description
Cable Modem ISP will automatically give you an IP address. Please refer to section
4.2.1 for details.
Fixed-IP xDSL ISP has given you a fixed IP address already. Please refer to section
4.2.2 for details.
PPPoE xDSL ISP requires you to use a Point-to-Point Protocol over Ethernet (PPPoE)
connection. Please refer to section 4.2.3 for details.
PPTP xDSL ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP)
connection. Please refer to section 4.2.4 for details.
L2TP XDSL This is not widely used. You need to know the PPTP Server address as
well as your name and password. Please refer to section 4.2.5 for details.
Telstra Big Pon d This option is for Australia only. Please refer to section 4.2.6 for details.
- 8 -

4.2.1 Cable Modem

With Cable Modem connection, the ISP will automatically give you an IP address. Some ISP may also require you to fill in additional information such as Host Name and MAC address (see screen below).
Note: The Host Name and MAC address section is optional and you can skip this section if your ISP does not require these settings for you to connect to the Internet.
Parameters Description
Host Name Type in the host name provided by your ISP if any; otherwise, just leave it blank. MAC Address To connect to Internet, your ISP will require a MAC address from your PC. Type in this
MAC address in this section or use the “Clone MAC Address” button to replace the WAN port MAC address with the your PC’s. To find out the PC’s MAC address, see Appendix A. (also see Glossary for an explanation on MAC address).
When the configuration finished, click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successful ly. Please refer to section 4.2.7 for the information of this screen.
- 9 -

4.2.2 Fixed-IP xDSL

Select Fixed-IP xDSL if your ISP has given you a specified IP address. Your ISP should provide all the information required in this section.
Parameters Description
IP address assigned by your Service Provider Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0). DNS Address The IP address of ISP’s DNS (Domain Name Service) Server. Service Provider Gateway Address
Please consult your local ISP about the information above. When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.
The IP address that your ISP should provide you.
The ISP’s IP address gateway.
- 10 -
4.2.3 PPPoE xDSL
Select PPPoE if your ISP requires the PPPoE protocol for Internet connectivity. Your ISP should provide all the information like user name, password required in this section.
Parameters Description
User Name Enter the User Name provided by your ISP for the PPPoE connection. Password Enter the Password provided by your ISP for the PPPoE connection. Service Name This is an optional parameter. Leave it blank unless your ISP requires it. MTU This is an optional parameter. You can specif y the maximum size of transmission
packet to the Internet. The range of the MTU will be from 512 to 1492. You can also consult you ISP for the optimal MTU as well. Default: 1392.
Connection Type
If you select “Continuous”, the router will always connect to the ISP. If the WAN line breaks down and links again, the router will auto-reconnect to the ISP. If you select “Connect On Demand”, the router will auto-connect to the ISP when a client in LAN want to use the Internet and keep connected until the WAN idle timeout. The router will close the WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface. The WAN connection will not disconnect due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP. Default: Continuous.
Idle Time You can specify an idle time threshold (minutes) for the WAN port. This means if no
- 11 -
packets have been sent (no one using the Internet) during this specified period, the router will automatically disconnect the connection from your ISP. Note: This “idle timeout” function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly, especially when your ISP charges you by time used.
When the configuration finished, click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successful ly. Please refer to section 4.2.7 for the information of this screen.

4.2.4 PPTP xDSL

Select PPTP if your ISP requires the PPTP protocol to connect to the Internet. Your ISP should provide all the information required in this section.
- 12 -
Parameter Description
Obtain an IP address Select it if the ISP requires you to obtain an IP address by DHCP automatically. Host Name Type in the host name provided by your ISP if any; otherwise, just leave it blank. MAC Address To connect to the Internet, your ISP will require a MAC address from your PC.
Type in this MAC address in this section or use the “Clone MAC Address” button to replace the WAN port MAC address with the MAC address of that PC. To find out the PC’s MAC address, see Appendix A. (also see Glossary fo r an
explanation on MAC address). Use the following IP address IP Address This is the IP address that your ISP has given you to establish a PPTP
Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0) Gateway Enter the IP address of the ISP’s Gateway. User ID Enter the User Name provided by your ISP for the PPTP connection.
Password Enter the Password provided by your ISP for the PPTP connection PPTP Gateway If your LAN has a PPTP gateway, enter that PPTP gateway’s IP address here. If
Connection ID This is the ID given by ISP. This is an optional parameter. MTU This is an optional parameter. You can specify the maximum size of
BEZEQ-ISRAEL Select this item if you are using the service provided by BEZEQ in Israel.
Select it if the ISP provides you a static IP to connect to the PPTP server.
connection.
Sometimes called a Connection ID.
you do not have a PPTP gateway, enter the ISP’s Gateway IP address above.
transmission packet to the Internet. The range of the MTU will be from 512 to
1492. You can also consult you ISP for the optimal MTU as well. Default: 1392
Connection Type
Idle Time You can specify an idle time threshold (minutes) for the WAN port. This means
If you select “Continuous”, the router will always connect to the ISP. If the WAN
line breaks down and links again, the router shall auto- reconnect to the ISP.
If you select “Connect On Demand”, the router will auto-connect to the ISP
when a client in LAN wants to use the Internet and keep connected until the
WAN idle timeout. The router will close the WAN connection if the time period
that no one is using the Internet exceeds the “Idle Time”.
If you select “Manual”, the router will connect to ISP only when you click
“Connect” manually from the Web user interface. The WAN connection will not
disconnected due to the idle timeout. If the WAN line breaks down and latter
links again, the router will not auto-connect to the ISP. Default: Continuous.
if no packets have been sent (no one using the Internet) throughout this
specified period, the router will automatically disconnect to with your ISP.
Note: This “idle timeout” function may not work due to abnormal activities of
- 13 -
some network application software, computer virus or hacker attacks from the
Internet. For example, some software sends network packets to the Internet in
the background, even when you are not using the Internet. So please turn off
your computer when you are not using it. This function also may not work with
some ISP. So please make sure this function can work properly, especially
when your ISP charges you by time used.
When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.
4.2.5 L2TP xDSL
Select L2TP if your ISP requires the L2TP protocol to connect to the Internet. Your ISP should provide all the information required in this section.
Parameter Description
Obtain an IP address Select it if the ISP requires you to obtain an IP address by DHCP automatically. Host Name If your ISP requires a Host Name, type in the host name provided by your ISP;
otherwise, just leave it blank. MAC Address To connect to the Internet, your ISP will require a MAC address from your PC.
Type in this MAC address in this section or use the “Clone MAC Address”
- 14 -
button to replace the WAN port MAC address with the MAC address of that PC.
To find out the PC’s MAC address, see Appendix A. (also see Glossary fo r an
explanation on MAC address. Use the following IP address IP Address This is the IP address that your ISP has given you to establish a L2TP
Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0) Gateway Enter the IP address of the ISP’s Gateway. User ID Enter the User Name provided by your ISP for the L2TP connection.
Password Enter the Password provided by your ISP for the L2TP connection L2TP Gateway If your LA N h as a L2T P gateway, enter that L2TP gateway’s IP address here. If
MTU This is an optional parameter. You can specify the maximum size of
Connection Type
Select it if the ISP provides you a static IP to connect to the L2TP server.
connection.
Sometimes called a Connection ID.
you do not have a L2TP gateway, enter the ISP’s Gateway IP address above.
transmission packet to the Internet. The range of the MTU will be from 1492 to
512. You ca n also consult you ISP for the optimal MTU as well. Default: 1392
If you select “Continuous”, the router will always connect to the ISP. If the WAN
line breaks down and links again, the router shall auto- reconnect to the ISP.
If you select “Connect On Demand”, the router will auto-connect to the ISP
when someone wants to use the Internet and keep connected until the WAN
idle timeout. The router will close the WAN connection if the time period that no
one is using the Internet exceeds the “Idle Time”.
If you select “Manual”, the router will connect to ISP only when you click
“Connect” manually from the Web user interface. The WAN connection will not
disconnect due to the idle timeout. If the WAN line breaks down and latter links
again, the router will not auto-connect to the ISP. Default: Continuous. Idle Time You can specify an idle time threshold (minutes) for the WAN port. This means
if no packets have been sent (no one using the Internet) throughout this
specified period, then the router will automatically disconnect the connection
with your ISP.
Note: This “idle timeout” function may not work due to abnormal activities of
some network application software, computer virus or hacker attacks from the
Internet. For example, some software sends network packets to the Internet in
the background, even when you are not using the Internet. So please turn off
your computer when you are not using it. This function also may not work with
some ISP. So please make sure this function can work properly, especially
when your ISP charges you by time used.
- 15 -
When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.

4.2.6 Telstra Big Pond

Select Telstra Big Po nd if yo u are liv e in Australia and yo ur ISP requires this protocol to c onnect to th e Internet. Your ISP should prov ide all the information required in this section.
Parameters Description
User Name Enter the User Name provided by your ISP for the connection. Password Enter the Password provided by your ISP for the connection. User Decide login server manually Login Server Please enter the Login Server IP address here. When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.
If you ISP has provide the login server IP address to you, please check this box and enter the Login Server IP address below.

4.2.7 Save Settings Successfully

When you press “OK” in above configuration, the settings will be saved and the screen appears as below. Before WMRT-414 restart, the settings are saved, but not function yet. Press “Apply” to restart the WMRT-414 for the change to take effect immediately.
- 16 -
Please wait for 30 seconds for WMRT-414 restart. After restart procedure finished, please click “OK” to return to HOME screen
.
- 17 -

Chapter 5 General Setup

After click on the “General Setup” button at the main Page, you should see the screen below.
The General Setup contains advanced features that allow you to configure the router to meet the network’s needs such as: Wireless, Port Forwarding, Virtual Server, Access Control, URL Blocking,
Special Applications, DMZ and other functions.
- 18 -

5.1 System

This section shows how to setup the Broadband router ’s system Time Zone, Password and Remote Management Administrator.
- 19 -

5.1.1 Time Zone

The Time Zone allows WMRT-414 to allocate its time with the settings configured; it will affect log display functions such as Security Log and Firewall settings.
Parameter Description
Set Time Zone Select the time zone of the country you are currently in. The router will set its time
based on your selection.
Time Server Address You can keep the default IP address or enter a new Time Server Address for this
device to synchronize its time. You can also refer to the web site
http://www.ntp.org to find a nearest time server.
Daylight Savings The router can also take Daylight savings into account. Select the check box to
enable your daylight saving configuration. You can set the days that you wish to start and stop daylight Savings Time.
After the setup completed, please click “Apply” to save the settings. After press “Apply”, you will see a web screen to prompt you the configurations save successfully. You may refer to section 4.2.7 for the information of this screen.
- 20 -

5.1.2 Password Setup

This screen allows you to change the management password.
Parameters Description
Current Password Enter your current password for the remote management administrator to
login to your Broadband router. New Password Enter you r new password. Confirmed Password Enter your new password again for verification purposes.
After the setup completed, please click “Apply” to save the settings. After press “Apply”, you will see a web screen to prompt you the configurations save successfully. You may refer to section 4.2.7 for the information of this screen.
Note: If you forget the password, please reset the WMRT-414 to the factory default by press RESET
button (on WMRT-414’s rear panel) over 10 seconds.
- 21 -
Loading...
+ 63 hidden pages