Copyright (C) 2005 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET Technology, This
User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all
accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form by any means by electronic or mechanical. Including photocopying, recording,
or information storage and retrieval systems, for any purpose other than the purchaser's personal use, and without
the prior express written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
CE mark Warning
The is a class B device, In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware
and software products by their trade names. In most, if not all cases, their respective companies claim these
designations as trademarks or registered trademarks.
(16mSec.), Comfort noise generation, Call progress detection, Gain Control
DECT Features
• DECT & GAP Compatible
• Base can register up to 8 Handsets
• Intercom call during external call, Call transfer between • handsets , three-way telephone meeting
• CID 50 locations
• Redial memory: 3 locations, 20 digits
• Adjustable ringer volume & melody
• 100 hours standby time, 8 hours talk time
• Hands-Free, Mute function
• Call duration time meter
• Transmitted distance: up to 50~200m indoor / up to 300m outdoor
Package Content
The contents of your product should contain the following items:
DECT VoIP router
DECT handset
Power adapter
Quick Installation Guide
User’s Manual CD
RJ-11 cable x 1
6
Physical Details
The following figure illustrates the front/rear panel of VIP-320.
Front Panel of VIP-320
Rear Panel of VIP-320
7
LED Display & Button
Front Panels Descriptions
Paring LED
Battery Charge
Handset charge Holder
Intercom
When the base connect to the handset
When charging the handset’s battery
Holder the handset
When it pairing
LED Indicators Descriptions
LINE
VoIP
Status
Ready
LINE LED will light when PSTN line is in use
VoIP LED will light when talking through VoIP
The Status LED will be flashing when the machine is operational
Ready LED will be ON when the registration toward the GK/SIP proxy is
successful
Back Panels Descriptions
DC9V
Power Adapter connecter
LINE
Reset
LAN 1 / LAN 2
WAN
ÍNote
Connect to the RJ-11 phone line
Reset to the default setting
10/100Mbps Ethernet port, used to connect PC or NB
10/100Mbps Ethernet port, used to connect ADSL or cable modem
The Default LAN IP is http://192.168.0.1 from factory.
Press RESET button on rear panel over 20 seconds will reset
the VoIP Router to this default LAN/WAN IP address and
Username/Password function.
8
Overview of DECT handset DCT-100
Keypad and button definition on DCT-100
Descriptions
INT
C
R
Number 0 –9 and #
*
Intercom conversation mode
Adjust the volume level during the conversation and menu selection on
the LCD display
Last Number Redial
Hang on / up telephone or pressing until to open /close speaker
Cancel and Clear
Power on / off
The function is as the same as the general phone set
Press * to switch PSTN
9
DCT-100 installation
The three rechargeable Ni-MH batteries (AAA size) come with your phone. Install the batteries before
using your phone.
1. Slide the battery cover in the direction of the arrow and pull it out.
2. Remove old batteries, if any, and insert new batteries as indicated, matching correct polarity (+, -).
3. Replace the battery cover, slide the cover up until it snaps shut.
ÍNote
ÍNote
This phone won't work by itself. It should be registered
to the main base unit inside the VIP-320.
Before initial using, it should be charged for 24 hours.
Reversing the orientation may damage the handset.
The battery needs to be replaced if it does not recover
its full storage capacity after recharging.
When replacing batteries, always use good quality Ni-MH
re-chargeable AAA size batteries.
Never use other batteries or conventional alkaline
batteries.
10
Chapter 2
2
Preparations & Installation
Physical Installation Requirement
This chapter illustrates basic installation of VIP-320
• Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors.
• TCP/IP protocol must be installed on all PCs.
For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem (for
WAN port usage)
Administration Interface
PLANET VIP-320 provides GUI (Web based, Graphical User Interface) for machine management and
administration.
Web configuration access
To start VIP-320 web configuration, you must have one of these web browsers installed on computer
for management
• Netscape Communicator 4.03 or higher
• Microsoft Internet Explorer 4.01 or higher with Java support
Default LAN interface IP address of VIP-320 is 192.168.0.1. You may now open your web browser, and
insert 192.168.0.1 in the address bar of your web browser to logon VIP-320 web configuration page.
VIP-320 will prompt for logon username/password, please enter: admin / 123 to continue machine
administration.
11
ÍNote
Please locate your PC in the same network segment
(192.168.0.x) of VIP-320. If you’re not familiar with
TCP/IP, please refer to related chapter on user’s manual
CD or consult your network administrator for proper network
configurations.
LAN/WAN Interface quick configurations
Nature of PLANET VIP-320 is an IP Sharing (NAT) device, it comes with two default IP addresses, and
default LAN side IP address is “192.168.0.1”, default WAN side IP address is “172.16.0.1”. You may
use any PC to connect to the LAN port of VIP-320 to start machine administration.
L Hint
In general cases, the LAN IP address is the default gateway
of LAN side workstations for Internet access, and the WAN
IP of VIP-320 is the IP address for remote calling party
to connect with.
LAN IP address configuration via web configuration interface
Execute your web browser, and insert the IP address (default: 192.168.0.1) of VIP in the adddress bar.
After logging on machine with username/password (default: admin / 123), browse to “Administrator”
--> “LAN setting” configuration menu:
Parameter Description
IP address LAN IP address of VIP-320
Default: 192.168.0.1
Subnet Mask LAN mask of VIP-320
Default: 255.255.255.0
Default Gateway Gateway of VIP-320
Default: 192.168.0.254
12
LHint
It is suggested to keep the DHCP server related parameters
in default state to keep machine in best performance.
After confirming the modification you’ve done, Please click on the Modify button to macke the changes
effective.
WAN IP address configuration via web configuration interface
Execute your web browser, and insert the IP address (default: 172.16.0.1) of VIP in the adddress bar.
After logging on machine with username/password (default: admin / 123), browse to “WAN Setting”
configuration menu, you will see the configuration screen below:
Connection Type Data required.
Obtain IP Address
L
Automatically
Specify an IP Address
PPPoE
Hint
Please consult your ISP personnel to obtain proper PPPoE/IP
address related information, and input carefully.
If Internet connection cannot be established, please check
the physical connection or contact the ISP service staff
for support information.
Save Modification to Flash Memory
In most circumstances, it is no need to configure the DHCP
settings.
The ISP will assign IP Address, and related information.
The ISP will assign PPPoE username / password for Internet
access,
Most of the VoIP router parameters will take effective after you modify, but it is just temporary stored on
RAM only, it will disappear after your reboot or power off the VoIP router, to save the parameters into
Flash ROM and let it take effective forever, please remember to press the Save Modification button
after you modify the parameters.
13
Loading...
+ 29 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.