Copyright (C) 2005 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET Technology,
This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all
accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any
electronic medium or machine-readable form by any means by electronic or mechanical. Including
photocopying, recording, or information storage and retrieval s ystems, for any purpose other than the
purchaser's personal use, and without the prior express written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and
applications, and makes no warranty and representation, either implied or expressed, with respect to the
quality, performance, merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for
any inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment
on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this
User’s Manual. PLANET makes no commitment to update or keep current the information in this User’s
Manual, and reserves the right to make improvements to this User’s Manual and/or to the products described
in this User’s Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
CE mark Warning
The is a class B device, In a domestic environment, this product may cause radio interference, in which case
the user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do
not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous
hardware and software products by their trade names. In most, if not all cases, their respective companies
claim these designations as trademarks or registered trademarks.
Revision
User’s Manual for PLANET PoE IP phone:
Model: VIP-103PT/VIP-153T/VIP-153PT
PoE IP Phone Specifications............................................................................................................43
3
PLANET PoE IP Phone User’s Manual
Chapter 1
Overview of the PoE IP Phone
Meeting the next-generation Internet telephony service demands, PLANET Technology provides
feature-rich, toll-quality Internet telephony service solutions. With 802.3af Power over Ethernet
(PoE) LAN interface supported, the VIP-103PT is H.323 v2/v3/v4 compliant with H.235 security
support, VIP-153PT is SIP 2.0 (RFC3261) compliant with SIP digest authentication supports. And
the VIP-153 is the cost-effective SIP IP Phone.
The VIP-103PT / VIP-153PT / VIP-153T ("IP Phone" in the following term) features high-quality
speakerphone technology, and includes an easy-to-use speaker on/off button and call
hold/transfer buttons for various voice services.
The IP Phone has additional features such as built-in PPPoE/DHCP clients, password-protected
machine management, LCD menu display, speed-dial keys, hands-free speakerphone, last
number redial, incoming message indicator, and user-intuitive web administration system.
The IP Phone is self-contained, service-integrated, intelligent phone features offering, and
powerful voice processing power . The IP Phone can ef fortlessly deli ver toll voice quality equivalent
to the regular PSTN connections utilizing cutting-edge Quality of Service, echo cancellation,
comfort noise generation (CNG) and voice compensation technology. Meanwhile, the dual
Ethernet interfaces on the IP Phone allow users to install in an existing network location without
interfering with desktop PC network connections. When installing the VIP-103PT / VIP-153PT /
VIP-153T, SIP IP Phone with IPX-2000 (PLANET IP PBX system), the VIP-153 series IP phones
can be easily integrated in your office; via the auto-config support for IPX-2000. No expertise
required building up the VoIP network deployment.
Besides, the VIP-103PT / VIP-153PT deliver more convenie nce, ef ficiency, innovation and benefits
fo VoIP in your daily life, the PoE interface and IP PBX shall replace your existing PBX system with
more feature and saving more. The IP Phones are ideal solution for office / home use as well as
installation for Internet Telephony Service Provider (ITSP) from leading vendors. It's the delivery
platform for IP voice services that makes benefit from the VoIP technologies in your daily life.
VIP/-103PT / VIP-153PT / VIP-153T Features
Simple Installation and administration
Configuration of the IP Phone can be performed in minutes via the keypad, or web interfaces.
Using the built-in LCD display, the IP Phone offers user-friendly configuration guidelines, machine
operation status, call status displays, and incoming call identification.
IP PBX system integration
Via auto-config support for IPX-2000, no expertise required to establish your office voice network.
VIP-153T and the VIP-153PT can help you to complete VoIP network deployment in minutes. The
same as H.323 model, VIP-103PT is able to be integrated with PLANET IP PBX system
IPX-1000/IPX-1500 as one of the extensions in your office network.
4
PLANET PoE IP Phone User’s Manual
Feature-rich keypad IP Phone
The IP Phone integrates a high-quality speakerphone with the Call Hold, Forward and Transfer
functions and also provides advanced telephone features, such as 10 spe ed-dial keys, last
number redial, incoming call history indicator in a much more convenient and functional mann er
than traditional telephone sets.
Dynamic IP address assignment, and voice communication
The IP Phone can act as a PPPoE/DHCP client, automatically obtaining an IP address for Internet
access.
Various field applications compliant
The IP Phone is capable of handling both peer-to-peer and H.323GK / SIP proxy registration,
authentication to interact with major H.323/SIP gateway/IP Phone in the market. The IP Phone
offers the most flexibility and interoperability with PLANET and 3rd party VoIP vendors, allowing
the deployment of both simple and complex VoIP networks such as ITSP,
PC-to-Phone/Phone-to-PC or enterprise VoIP environments.
Standards compliant
The VIP-103PT complies with H.323 version 4, and supports H.323 fast start, H.245 tunneling,
GateKeeper H.235 security mode for different occasions. The VIP-153T / VIP-153PT complies
with SIP 2.0 (RFC3261), interoperates with 3rd party SIP voice gateways/terminal/software as well
as other PLANET VoIP products. Supported Voice codecs and VoIP technologies are: G.723,
G.729ab, G.711u-law/a-law; Voice Activity Detection (VAD), and the Comfort Noise Generation
(CNG).
1.1 Hardware Overview
1.1.1 Front View and Keypad function
PoE IP phone overview
5
PLANET PoE IP Phone User’s Manual
Keypad Description
1 Light
The red light goes on-off when there is an incoming call.
2 LCD Display
3
4
5 +OUT VOL-
6 SPEAKER
7 HOLD
8
9 MESSAGE
10 Menu / OK
11 Cancel
“Í UP” Key
“Æ DOWN” Key
- IN VOL+
NET
Menu and all status shall be displayed for users.
To scroll up the menu items or left delete a digit per each key
press while editing the settings.
To scroll up the menu items or left delete a digit per each key
press while editing the settings.
When the IP phone is at idle state or talking on handset or
speaker, this key is used to increase/decrease the volume of
the voice sound.
Users are able to increase or decrease the volume which they
send out to remote party.
To switch between the usage of the handset and the speaker
devices.
To hold the conversation.
When users are not successfully registered to their service
provider, this button light wi ll turn on-off. User can press this
button to try to register again to their service provider.
This is for future use of functions upgrade.
To bring out the menu selection while IP phone is in idle state.
To be used as “OK” key while editing. To be used as “Dial Out”
key when on dial mode.
To escape to an upper layer menu selection or to cancel the
current edit.
12 TXT ←→ NUM
13 TRANSFER
14 Redial / Dial
Speed Dial
15
M1 – M10
16 Phone Book
Press this button and alphabets shown on the keypads will be
displayed.
To transfer an active call (incoming call answered or outgoing
call accepted) to another IP phone.
Press to dial the last dialed number when the IP phone is
off-hooked.
To make a speed dial call by pressing the speed dial key M1 –
M10.
By pressing this button to store up to 50 phone numbers.
6
PLANET PoE IP Phone User’s Manual
1.1.2 Rear View
Rear Panel of VIP-103PT/VIP-153PT/VIP-153T
1 PC
RJ-45 connector, to maintain the existing network structure,
connected directly to the PC through straight CAT-5 cable
L
2 WAN
3 7V DC
Hint
RJ-45 connector, for Internet access, connected directly to
Switch/Hub through straight CAT-5 cable.
802.3af PoE support in PT model
7V DC Power input outlet
yThe Power over Ethernet support on PLANET PoE IP phones
complies with the 802.3af standards. Using non-802.3af
compliant PoE device will burn up the IP Phone
permanently.
7
PLANET PoE IP Phone User’s Manual
Chapter 2
Configuring the PoE IP Phone through
LCD Phone menus
2.1 Initialize VIP103PT/VIP-153PT/VIP-153T
STEP 1:
Power on machine, the LCD screen displays flashing greeting as below:
STEP 2:
Wait for 10 seconds, the main LCD screen sh all be shown as below, and when the
Internet access is available, the
SNTP server. The current time will be displayed on the LCD.
STEP 3:
Press MENU to enter configuration mode then press OK button to enter sub menus;
press CANCEL can jump out current menu to previous level.
1. View
2. Configure (Password: 123)
3. Advanced Setting (Password: 1234)
Starting
…
VIP-103PT / VIP-153PT / VIP-153T will connect to the
Hi (GK off)
Date Time
LCD screen of VIP-103PT (H.323)
SIP (Proxy off)
Date Time
LCD screen of VIP-153PT/VIP153T (SIP)
8
PLANET PoE IP Phone User’s Manual
2.2 LCD Menu Configuration
LCD menu configuration for VIP-103PT
1st Level 2nd Level 3rd Level
IP PBX mode
IP Address
View
Configure
Reboot
1.1 (On/Off)
If Yes: Name
Number
1.2 Hotline 1.2.1 (Yes/No) Auto
Check the active network parameters in machine
2.1 Network Value 2.1.1 IP Address
2.2 IP PBX Mode
2.2 Ping
2.3 GK IP Address
2.4 Firmware Version
Password:123
3.1 Network 3.1.1 (Yes/No) Dynamic IP
3.2 VOIP 3.2.1 Telephone Number
3.3 Forward Mode 3.3.1 (Yes/No) Immediate
Reset the PoE IP Phone
1.2.2 (Yes/No) Manual
If Yes: IP Address
2.1.2 Network Mask
2.1.3 Default Route
2.1.4 DNS Server
3.1.2 (Yes/No) PPPoE
If Yes: PPPoE User Name
PPPoE Password
3.1.3 Fixed IP
Network Mask
Default Route
DNS Server
3.1.4 GMT
3.2.2 Password
3.2.3 H.323 ID
3.2.4 (Yes/No) GK mode
3.2.5 GK IP
3.2.6 RAS Port
3.2.7 Q931 Port
3.2.8 Frame Size
(True/False) LowRate
If Yes: Immediate Number
3.3.2 (Yes/No) Busy
If Yes: Busy Number
3.3.3 (Yes/No) No Answer
If Yes: No Answer Number
IP Address
No Answer Time
9
PLANET PoE IP Phone User’s Manual
LCD menu configuration for VIP-153PT/VIP-153T
1st Level 2nd Level 3rd Level
View
Configure
1.1 Network Value 1.1.1 IP Address
1.1.2 Network Mask
1.1.3 Default Route
1.1.4 DNS Server
1.2 Ping
1.3 Restart
1.4 Firmware Version
1.5 (Yes/No) PKT Trace
Password:123
2.1 Network 2.1.1 (Yes/No) Dynamic IP
2.1.2 (Yes/No) PPPoE
If Yes: PPPoE User Name
PPPoE Password
2.1.3 Fixed IP
Network Mask
Default Route
DNS Server
2.1.4 GMT
2.2 SIP 2.2.1 Username
2.2.2 Telephone Number
2.2.3 Password
2.2.4 (Yes/No) Proxy mode
If Yes: Proxy Server Address
Proxy Port
2.2.5 (Yes/No) Outbound Proxy
If Yes: Outbound Proxy Address
Outbound Proxy Port
2.2.6 SIP Domain Name
2.2.7 Frame Size
(True/False) LowRate
2.3 Forward Mode 2.3.1 (Yes/No) Immediate
If Yes: Immediate Number
2.3.2 (Yes/No) Busy
If Yes: Busy Number
2.3.3 (Yes/No) No Answer
If Yes: No Answer Number
IP Address
No Answer Time
10
PLANET PoE IP Phone User’s Manual
“View” menu
In the “View” main menu, there are submenus, users may check these items for machine
information and also provide some simple functions to check the network status of the IP Phone.
1.1 View current network settings
By selecting “View” → ”Network”, you could see the active network parameters in machine.
1.2 Ping
By selecting “View” → ”Ping” and key in the IP address or domain name of another device,
the IP Phone can verify the connection between remote device. The “ping” command also
can be used to verify the Internet connection status via pinging an Internet node
1.3 Restart
By selecting the “View” → ”Restart”, the PoE IP Phone will reboot itself immediately. This
“warm restart” is different from the power down/up (col d restart).
yRestarting the IP phone will perform the following tasks:
L
Hint
• Disconnect all the voice communications, and Internet
connections
• Registration toward the gatekeeper/proxy server will be
torn down.
1.4 Display current firmware version
By selecting the “View” → ”Firmware Version”, the users can view current software version
in the PoE IP Phone.
1.5 PK Trace for signal monitoring
PLANET PoE IP Phones integrate self-analysis packet tracing algorithm, which is able to
perform machine signaling monitoring task, By enabling the “View” → ”PKT Trace” to (Yes),
the LCD screen will display signaling messages received, and this can be used to monitor
the signals and identify the machine running status.
Network Configuration
The first thing in using the PoE IP Phone is to set the network configuration to let the IP
Phone connect to Internet. Depends on the network environment and phone models, please
use the proper method to configure the IP Phone to connect to Internet.
2.1.1 Dynamic IP Method (DHCP Client)
When the IP phone installed in a DHCP server enabled network environment (for example,
cable modem connection or corporation internal network). Please browse to machine
11
PLANET PoE IP Phone User’s Manual
network configuration menu, and enable the DHCP cli ent in Dynamic IP selection menu and
the IP phone will obtain the IP p arameters dynami cally, and connect to Internet automatically .
Configuration steps:
Configure → Password:123 → Network → (Yes/No) Dynamic IP
2.1.2 PPPoE
Most of the broadband network environment provided now by ISP is the ADSL connection. In
the ADSL environment, the IP Phone can directly connect to the ADSL modem by setting the
PPPoE account (username and password) provided by ADSL service provider, the
configuration steps are shown below: .
Please browse to machine network configuration menu, and enable the PPPoE service in
L
machine, and setup the username/password fields for Internet access.
PPPoE Username – please input the user name of the account given by ADSL ISP.
PPPoE Password – please input the password of the account given by ADSL ISP.
2.1.3 Fixed IP
Under the “Fixed IP” submenu, please key in the IP address, network mask and default
router settings provided by your ISP or private IP address.
Configure → Password:123 → Network → Static IP
Once all the network settings are completed, please restart your
IP phone. After rebooting, please check Internet connection status
via View -Æ Ping, then insert in a public, live IP address (for
Hint
example, 168.95.1.1) to ping it. When the response is ok, then the
network configurations are completed.
2.1.4 GMT
Via selecting the time zone in the GMT menu, VIP-103PT/VIP-153PT/VIP-153T is able to
retrieve time information from timeserver on the net.
Configure → Password:123 → Network → GMT
12
PLANET PoE IP Phone User’s Manual
2.2 Registration to H.323 gatekeeper / SIP Proxy Server
After setting up the network parameters, the IP Phone is able to perform registration to the
H.323 gatekeeper (VIP-103PT) or SIP Proxy server (VIP-153PT/VIP-153T) when you’ve
been assigned the account from VoIP vendor/service provider.
2.2.1 Registration to a H.323 gatekeeper (VIP-103PT)
When VIP-103PT is installed in an H.323 GK enabled network, the VIP-103PT registers to
the gatekeeper for voice communications. Following descriptions are parameters to
complete the registration.
Configure → Password:123 → H.323
Telephone Number:
Telephone phone number used to register toward the gatekeeper.
Password:
H.323 ID:
The telephone number, H.323 ID and password fields are
LNote
application-oriented parameters. Please be sure to check with your
service provider to get the proper information before setting up
these fields.
GK mode (Yes/No):
Password used to register to the gatekeeper.
This password will be encapsulated in the H.235 message for authentication
purpose. Not every
this field if your ISP does not provide this information.
The H.323 ID will be used to register to the gatekeeper. Not every
demands this value for authentication; please skip this field if your ISP does not
provide this information.
Selecting Yes will enable machine in GK mode, and register to the gatekeeper.
(Machine default mode is Peer-to-Peer (P2P))
If you’d like to change the GK settings, it is suggested to log in machine web
gatekeeper demands this value for authentication; please skip
gatekeeper
interface, and browse to H.323 configuration menu to adjust related parameters.
When VIP-103PT fails to register with the gatekeeper, the IP phone still able to
establish voice calls toward other calling parties Peer-to-Peer via dialing the IP
address directly on the keypad.
13
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.