USB
To
10/100Mbps
Fast Ethernet Adapter
UE-9500
User’s Manual
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits of a Class B
computing devices, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
If you suspect this product is causing interference, turn your computer on and off
while your radio or TV is showing interference. If the interference disappears then
when you turn the computer off and reappears then you turn the computer on,
something in the computer is causing interference.
You can try to correct the interference by one or more of the following measures:
1. Reorient/Relocate the receiving antenna.
2. 2.Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit difference from that to
which the receiver is connected.
4. Ensure that all expansion slots (on the back or side of the computer) are covered. Also
ensure that all metal retaining brackets are tightly attached to the computer.
1. Introduction
Thanks you for purchasing our UE-9500. This guide is to provide the installation
and usage of this adapter for network installers and users.
The UE-9500 provides a convenient and cost-effective way of connect the
notebook or desktop PC to an IEEE 802.3/802.3u standard Fast Ethernet network based on the Universal Serial Bus (USB). This is designed for both the
Notebook and Desktop PC that has USB connector and operating system supported. Using UE-9500 you can simplify your Network connections at home,
office and even on the road.
Full/Half Duplex operation mode is auto-detected. In Full-Duplex mode, the USB
adapter is connected to a switch on a dedicated segment. With transmission and
reception taking place simultaneously, data transfer is double.
This adapter has support Windows 95(OSR2.1)/98/Me/2000/XP. Whatever your
requirements are ease of installation, superior performance or responsive
support backed up by unlimited technical support, this adapter is the superior
choice.
2. Features & Specifications
(1) Features & Benefits
q USB specification 1.0 and 1.1 compliant and Plug & Play Support
q Support Full-Speed USB data transfer bandwidth, all USB standard
commands and Suspend/Resume detection function.
q Complies with IEEE 802.3 10BaseT and 802.3u 100BaseTX standards.
q Automatically negotiates 10 or 100Mbps connection rate, depending
on speed of the network.
(2) Technical Specification
q USB Standards: USB Specification 1.1
q Ethernet Standards: IEEE 802.3 and 802.3u
q Connectors: RJ45 x 1, USB Type B x 1
q LEDs: 2; 100M, LNK/ACT
q Driver Support: NDIS driver - Microsoft Windows 95OSR2.1/98/Me/XP/2000
q Dimensions: 78mm x 45mm x 23mm (L x W x H)
q Weight: 50g
q Temperature: 0 to 50
q Humidity: 10% to 90%
q Certification: FCC, CE Mark
o
C
3. Installation
The diskette that comes with the package contains the device drivers of this
USB Fast Ethernet Adapter. The hardware and software drivers installation are
described as following,
(1) Hardware Installation
Step1. Connect the RJ-45 connector of UE-9500 to the 10/100Mbps
Hub/Switch of your LAN by using a twisted-pair cable. (maximum
length 100 meters). Use Category 3, 4 or 5 cable for 10 Mbps
Ethernet and Category 5 cable for 100 Mbps Fast Ethernet.
Step2. Connect the USB Type B connector of the USB Adapter and your
PC’s or USB Hub’s USB Type A connector by using the standard
USB Cable (max length 5m)
(2) Software Installation
The drivers and utilities are supplied by the diskette included in this
package.
Before Installing the Device Driver
Before you go on installing this USB device driver, you must first make
sure that the USB controller of your computer has been properly detected
and configured under Windows. Also make sure that the USB port is enabled. Check the user’s manual of your computer for more information on
how to use the USB port.
Driver Installation of Win95OSR2.1/98/Me
1. Connect the UE-9500 to your PC
2. Windows will detect this device and the New Hardware Wizard will
appear.
3. Installation will ask you to select which driver you want to install,
please select "Driver from disk provided by hardware manufacturer".
4. Insert the driver disk into drive A and specify the setup file path name
A:\.
5. If Windows appears a message that it cannot found NET8511.INF or
NET8511.SYS, please specify the driver path name A:\
6. Windows will appear some messages to ask Windows system disk,
please insert the Windows system CD to your CD-ROM to complete
setup step.
7. Windows will finish the installation procedure automatically, then ask
you restart the system. Please click “Yes” to restart.
Driver Installation of Win2000/XP
1. Connect the UE-9500 to your PC
2. Windows will detect this device and the New Hardware Wizard will
appear.
3. Install Hardware Device Driver Wizard will ask you how to install,
please select "Search for a suitable driver for my device".
4. Locate Driver Files Wizard will ask you where is the driver location,
please select "Floppy disk driver".
5. When a dialog box appears to prompt you the Digital Signature not
found, please press "Yes" button to continue.
6. If Win2000/XP appear a message that it cannot found NET8511.INF or
NET8511.SYS, please specify the driver path name A:\.
7. Win2000/XP will appear some messages to ask you the Windows2000
/XP system disk, please insert the Windows system CD to your
CD-ROM and click “OK” to continue.
8. After finished the installation, please restart your PC.
4. Trouble-Shooting
If you experience any problems with this Adapter, please make sure the appropriate driver is loaded firstly, the proper cable is connected to the adapter
and the hub complies with the adapter specification, then check the LED.
This adapter provides two LEDs to indicate network status.
(1) 100
This LED indicates the connection speed of the USB Ethernet Adapter.
When the Light is OFF, it indicates that the 10Mbps UTP connection is
established. When the Light is ON, it indicates that the 100Mbps Fast
Ethernet connection is established.
(2) LNK/ACT
The LNk/ACT LED indicates that the 10/100Mbps UTP connection has been
LINK OK or not. When the light is OFF, it indicates that the 10/100Mbps
port has not been connected or LINK not OK. When the light is ON, it indicates that the 10/10Mbps port connect OK. When the light is Blinking, it
indicates that there is traffic flow on the network that the adapter is connected to.
Loading...