5/8-Port 10/100/1000Mbps
Gigabit Ethernet Switch
GSD-Series
User's Manual
1. Package Contents 2. Product Features
Check the contents of your package for following
parts:
● Gigabit Ethernet Switch x 1 ● 5/8-Port 10/100/1000Mbps Gigabit Ethernet ports
● User's manual x 1 ● Features Store-and-Forward mode with
● Comply with IEEE 802.3, 10Base-T, IEEE 802.3u
100Base-TX, IEEE 802.3ab 1000Base-T
wire-speed filtering and forwarding rates
● Power adapter x 1
● Rubber feet x 4
If any of these are missing or damaged, please contact
your dealer immediately, if possible, retain the carton
including the original packing material, and use them
● Hardware based 10/100Mbps, half / full duplex and
1000Mbps full duplex mode, flow control and
auto-negotiation
● IEEE 802.3x flow control for full duplex operation
and Back pressure for half duplex operation
against to repack the product in case there is a need to
return it to us for repair.
● Integrated address look-up engine, support 4K
absolute MAC addresses
● Automatic address learning and address aging
● Supports Auto MDI/MDI-X function
● Support CSMA/CD protocol
3. Switch Front Panel
Figure 1-1 & 1-2 & 1-3 & 1-4 shows a front panel of GSD-503 / GSD-504 / GSD-803 / GSD-804.
Figure 3-1 GSD-503 front panel Figure 3-2 GSD-504 front panel
Figure 3-3 GSD-803 front panel Figure 3-4 GSD-804 front panel
4. LED Indicators
LED Color Function
PWR Green Lights to indicate that the Switch is powered on.
1000 Green
LNK/ACT Green Lit: indicate the link through that port is successfully established.
Lit: indicate that the port is operating at 1000Mbps.
Off: indicate that the port is operating at 10Mbps or 100Mbps.
Blinks to indicate that the Switch is actively sending or receiving data over that port.
5. Switch Rear Panel
Figure 1-5 & 1-6 & 1-7 & 1-8 shows a rear panel of GSD-503 / GSD-504 / GSD-803 / GSD-804.
Figure 5-1 GSD-503 rear panel Figure 5-2 GSD-504 rear pane
Figure 5-3 GSD-803 rear panel Figure 5-1 GSD-804 rear panel
Power Notice:
1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all
the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from
network data loss or network downtime.
2. In some area, installing a surge suppression device may also help to protect your Switch from being damaged by
unregulated surge or current to the Switch or the power adapter.
6. Installing the Switch
This part describes how to install your Gigabit Ethernet Switch and make connections to it. Please read the following
topics and perform the procedures in the order being presented.
Note: This Switch does not need software configuration.
Desktop Installation
To install the Switch on desktop, simply follow the next steps:
Step 1: Attach the rubber feet to the recessed areas on the bottom of the Switch.
Step 2: Place the Switch on desktop near an AC power source.
Step 3: Keep enough ventilation space between the Switch and the surrounding objects.
Note: When choosing a location, please keep in mind the environmental restrictions discussed in Product
Specifications.
Step 4: Connect your Switch to network devices.
A. Connect one end of a standard network cable to the 10/100/1000 RJ-45 ports on the rear panel of the Switch.
B. Connect the other end of the cable to the network devices such as printer servers, workstations or
routers…etc.
Step 5: Supply power to the Switch
A. Connect one end of the power cable to the Switch
B. Connect the 12V DC power adapter to a standard wall outlet
When the Switch receives power, the Power LED should remain solid Green
7. Product Specifications
Product GSD-503 GSD-504 GSD-803 GSD-804
Hardware Specification
10/100/1000Base-T Ports 5 Auto MDI/MDIX ports 8 Auto MDI/MDIX ports
Dimensions (mm)
Weight (kg)
Power Requirement
Power Consumption /
Dissipation
Switch Specification
Switch Processing Scheme Store-and-Forward
Address Table 4K entries
Flow Control
Switch fabric 10Gbps 16Gbps
Throughput (packet per
second)
Jumbo packet size 9K
Standards Conformance
155 x 86 x 26 176 x 106 x 30 155 x 86 x 26 176 x 106 x 30
0.36 0.16 0.39 0.21
External power adapter 12V 1A
5.4 watts / 18 BTU 8.1 watts / 27 BTU
Back pressure for half duplex, IEEE 802.3x Pause Frame for full
duplex
7.44Mpps 11.9Mpps
IEEE 802.3 (Ethernet)
Standards Compliance
Temperature
Humidity Operating
Regulation Compliance FCC Part 15 Class A, CE
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3x (Full-duplex flow control)
Operating: 0~50 degree C
Storage: -40~70 degree C
Operating: 5% to 90%, Storage: 5% to 90% (Non-condensing)
8. Customer Support
Thank you for purchase PLANET products. You can browse our online FAQ resource at the PLANE T
Website first to check if it could solve you issue. If you need more suppor t information, please contact
PLANET switch support team.
PLANET online FAQ :
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address :
support_switch@planet.com.tw
Copyright © PLANET Technology Corp. 2008.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All oth er trademarks belong to their
respective owners.
Loading...