Planet Technology FT-8 Series User Guide

Trademarks
Copyright PLANET Technology Corp. 2002. Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. The information in this manual is subject to change without notice. All other trademarks belong to their respective owners.
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or ex­pressed, with respect to the quality, performance, mer­chantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this Users Manual is accurate; PLANET disclaims liability for any inac­curacies or omissions that may have occurred. Information in this Users Manual is subject to change without notice and does not represent a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this Users Manual. PLANET makes no commitment to update or keep current the information in this Users Manual, and reserves the right to make improvements to this Users Manual and/or to the products described in this Users Manual, at any time without notice. If you find infor­mation in this manual that is incorrect, misleading, or incom­plete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea­sonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this users guide, may cause harmful interference to radio com­munications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Revision
User's manual for PLANET Fast Ethernet Converter
Multi-mode: FT-701B, FT-702B, FT-703, FT-704, FT-705 Single-mode: FT-702S15, FT-702S35, FT-702S50,
Rev 3.0 (Oct. 2002) Part No.
FT-703S, FT-706A15, FT-706B15
2010-000001-002
Table of Contents
CHAPTER 1 OVERVIEW..............................................1
CHAPTER 2 MODEL LIST............................................1
CHAPTER 3 CHECKLIST.............................................2
CHAPTER 4 PRODUCT OUTLOOK..............................2
CHAPTER 5 INSTALLING THE CONVERTER.............3
CHAPTER 6 DUPLEX MODE SETTING.......................4
CHAPTER 7 THE LED INDICATIONS...........................5
CHAPTER 8 CABLE CONNECTION PARAMETER......6
CHAPTER 9 TECHNICAL SPECIFICATIONS...............7
CHAPTER 10 POWER INFORMATION........................7
- 1 -
Chapter 1 OVERVIEW
Thank you for purchasing PLANET FT-70X family Fast Ethernet Twisted pair to Fiber-optic Converter. This converter is used to convert one type media signal to other type equivalent that allows two type segments connect easily, efficiently and inex­pensively. This converter can be used as a standalone unit or as a slide-in module to the 10/19 media chassis (up to 15 units) for a TP and Fiber combined networks at a central wiring closet. Please contact with your sales representative for more about the 19 media chassis.
Chapter 2 MODEL LIST
Your Fast Ethernet Converter comes with one of the following models.
ð
FT-701B on board ST fiber connector
ð
FT-702B/S on board SC fiber connector
ð
FT-703/S on board MT-RJ fiber connector
ð
FT-704/S on board VF-45 fiber connector
ð
FT-705/S on board LC fiber connector
ð
FT-706A15 on board single SC fiber connector
ð
FT-706B15 on board single SC fiber connector
Models with last two numbered characters indicates the fi­ber-port is with Single-Mode optic fiber connector and the number indicates the maximum distance in km. The rest will be Multi-Mode optic fiber models.
In the following sections, the term FT-70X indicates the product family above.
- 2 -
Chapter 3 CHECKLIST
Your FT-70X carton should contain the following items:
ð
The Fast Ethernet Converter
ð
AC-DC Power Adapter (Output: 5VDC, 2 A max.)
ð
This users manual
If any item is missing or damaged, please consult the dealer from whom you purchased your Fast Ethernet Converter.
Chapter 4 PRODUCT OUTLOOK
Right View (FT-70X)
There are one RJ-45 Twisted-Pair jack, one fiber-optic connector and six LED indicators on this side.
The fiber connector is different from model to model. Please refer to the section 2 Model List and section 9 Technical Specification for detail.
Left View (FT-70X)
One DC jack for DC power input.
- 3 -
Side View (FT-70X)
DTE MPR
One DIP Switch for TP Device selection.
Chapter 5 INSTALLING THE CONVERTER
Please follow these steps to install the converter:
Turn off the power of the device/station in a network to which the FT-70X will be attached.
Ensure that there is no activity in the network.
Attach fiber cable from the FT-70X to the fiber network. TX,
RX must be paired at both ends for some two connectors models.
Attach a Cat. 5 UTP cable from the 100Base-TX network to
the RJ-45 port on the FT-70X.
Connect the 5VDC power adapter to the FT-70X and verify that the Power LED lights up.
Turn on the power of the device/station, the TX Link and FX
Link LEDs should light when all cables are attached.
FT-70X
- 4 -
Note:
n
RJ-45/STP, UTP Cat 5, straight-through cable is ac­cepted.
n
Cabling from FT-70X TP port to a TP device is as below:
q
To Workstation: DIP switch on DTE
q
To Hub/Switch: DIP switch on MPR
n
Please refer to section 8 for more about the wiring dis­tance of your TP, Optic-fiber networks.
n
Please note FT-706A15/706B15 is designed to work to­gether. It means you must connect FT-706A15 to FT-706B15 from them to work normally. If both ends are FT-706A15 or FT-706B15, they cant work normally and may damage the fiber connectors.
Chapter 6 DUPLEX MODE SETTING
The twisted pair port of FT-70X support duplex mode selection by Auto-Negotiation (A-N). The following is the duplex mode parameters:
Fast Ethernet Device FT-70X Duplex Mode support
Fast Ethernet Hub Half-Duplex Fast Ethernet Switch (without A-N) Half-Duplex Fast Ethernet Devices * Support Auto-Negotiation
Note: Normally, an A-N switch will be detected and set to
Full-duplex where a dual-speed hub will be detected and set to Half-Duplex.
Full-Duplex / Half-Duplex
- 5 -
Chapter 7 THE LED INDICATIONS
LED COLOR Status DESCRIPTION
TP ACT Green
TP Link Green ON FX ACT Green Blinks FX Link Green ON
FDX* Green ON PWR Green ON
If fiber-optic is not present for converter self
Blinks
-diagnose / detecting If both ports link with any TP packets
Blinks
transmitting
OFF
Fiber-optic link is present With no TP/FX LINK on, i.e. only turn on the
OFF
power and the ACT do not blink at all, pleas consult your local dealer TP connection is good When any FX packets transmitting When Fiber connection is good When Full-duplex mode is detected in TP port When +5VDC power detected
Note: Fiber-optic partner should be set to the correct mode
according to this FDX indicator for optimal network performance.
- 6 -
Chapter 8 CABLE CONNECTION
PARAMETER
The cable distance limitations are as below:
Duplex Connection Limitation (max.) Twisted Pair
Half / Full
Multi-Mode Converters
MM Half*
MM Full
Single-Mode Converters (FT-70xS, FT-706A15/706B15)
SM Full
*Note: If the fiber port works on half duplex, please note that
Node to Node Node to Switch/Hub
Node to Node Node to Switch Node to Node Node to Switch
Node to Node Node to Switch
100 meters
412 meters
2 kilometers
FT-70xS15: 15 km FT-70xS35: 35 km FT-70xS50: 50 km FT-706A15: 15 km FT-706B15: 15 km
Fast Ethernet/100Base-TX network allows 512 bit-time delay between any two nodes/stations in a collision domain (when work in half duplex). The overall bit time of TP/Fiber wires and devices must below 512 bit-time in one network segment. To extend the distance, however, you may use switch to break up a collision domain and extend the distance.
- 7 -
Chapter 9 TECHNICAL SPECIFICATIONS
The FT-70X comes with the following features:
Standard TP Connector
Fiber Connector
Optical wave­length
Data Rate Duplex mode LED indicators Power Re­quirement Ambient Tem­perature Humidity Dimension
Cable
IEEE 802.3u, 100Base-TX and 100Base-FX One RJ-45 Twisted Pair, EIA568 connectors FT-701B: ST FT-702B: SC FT-702S series: SC FT-703 series: MT-RJ FT-704 series: VF-45 FT-705 series: LC FT-706A/FT-706B series: single SC FT-706A15: Tx-1310nm, Rx-1550nm FT-706B15: Tx-1550nm, Rx-1310nm Others: Tx and Rx -1310nm 100Mbps Full or half-duplex mode by Auto- Negotiation PWR, TX LNK/ACT, FX LNK/ACT, FDX
5V ,2A 0° to 50°C
5% to 90% 26 x 70 x 97mm (HxWxD)
UTP : Cat 5 UTP cable
Fiber-MM: 50/125 µm or 62.5/125 µm optic fiber
Fiber-SM: 8.3/125, 8.7/125, 9/125 µm optic fiber
Chapter 10 POWER INFORMATION
The power jack of FT-70X is with 2.5mm in the central post and required +5VDC / 2A power input. It will conform to the bundled AC-DC adapter and PLANETs Media Chassis. Should you have the problem to make the power connection, please contact your local sales representative.
Please keep the AC-DC adapter as spare parts when your FT-70X is installed to a Media Chassis.
Part No.:
2010-000001-002
Loading...