Planet Technology FNSW-2400S User Manual
NOVASwitch
FNSW-1600S
10/100Base-TX
Fast Ethernet Smart Switch
Trademarks
Copyright PLANET Technology Corp. 2001.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET
Technology Corp. All other trademarks belong to their
respective owners.
FCC Warning
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
Instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
Revision
PLANET NOVASwitch User's Manual
FOR MODELS: FNSW-1600S
Part No.: EM_FNSWV2
Before Starting
In this User's Manual "Switch" is used for FNSW-1600S,
“NovaSwitch” for PLANET’s 19”-range Ethernet Switch,
where “switch” represent the third part Switch.
PLANET NOVASwitch series
TABLE OF CONTENTS
1. UNPACKING INFORMATION...........................................5
2. PRODUCT INTRODUCTION .............................................7
2.1 KEY FEATURES....................................................................7
2.2 FRONT PANEL......................................................................8
2.2.1 Ports Speed..................................................................8
2.2.2 Cabling ......................................................................8
2.2.3 MDI Switch..................................................................9
2.2.4 Status LEDs .................................................................9
2.3 THE REAR PANEL............................................................... 10
2.3.1 Extension Slot............................................................10
2.3.2 Power Connector .......................................................10
2.3.3 Fan…… ....................................................................10
2.3.4 RS-232 Console .........................................................11
3. INSTALLATION ................................................................13
3.1 RACK-MOUNT INSTALLATION ..............................................13
3.2 DESKTOP INSTALLATION......................................................13
3.3 POWER NOTES:....................................................................14
4. CONSOLE CONFIGURATION.........................................15
4.1 CONNECT TO PC.............................................................15
4.2 PORT SETTING.....................................................................16
4.2.1 Auto Neg. Setting.......................................................16
4.2.2 Speed Setting .............................................................17
4.2.3 Duplex Setting ...........................................................17
4.2.4 Flow Control Setting.................................................. 17
4.3 VLAN SETTING..................................................................18
4.4 TRUNK SETTING................................................................19
4.4.1 TRUNKING GROUP SETTING ........................................... 19
4.5 PORT ENABLE/DISABLE SETTING .........................................20
4.6 ADDRESS AGING SETTING....................................................21
4.7 RESTORE TO FACTORY DEFAULT .......................................... 21
FNSW-1600S User's Manual
5. OPTIMIZING CONFIGURATION...................................25
5.1 PRIOR TO INSTALLATION.................................................... 25
5.2 HALF- AND FULL-DUPLEX.................................................. 25
5.3 FAST ETHERNET ................................................................ 26
5.4 AUTO-NEGOTIATION..........................................................27
5.5 MAC ADDRESS TABLE ...................................................... 27
5.6 SAMPLE APPLICATION........................................................28
6. TROUBLESHOOTING......................................................29
7. PRODUCT SPECIFICATIONS..........................................31
8. RJ-45 PIN ASSIGNMENT..................................................32
8.1 STRAIGHT-THROUGH/CROSSOVER CABLE...........................32
PLANET NOVASwitch series
1. UNPACKING INFORMATION
Thank you for purchasing a PLANET NOVASwitch series
Ethernet Switches. Before continuing, please check the
contents of the product package. This product package should
contain the following items:
• One NOVASwitch Ethernet Switch
• One Power Cord
• Two Rack-Mounting Brackets with Attachment Screws
• This User’s Guide
• RS-232 Console Cable
Please inform your local dealer/supplier immediately if any item
is found to be defective, damaged or missing. Retain the
original packaging (carton), including the packing materials,
and use them to re-pack the product in the unlikely event there
is a need to return it to us for repair.
.
FNSW-1600S User's Guide
5
This page intentionally left blank!
PLANET NOVASwitch series
2. PRODUCT INTRODUCTION
NOVASwitch Ethernet Switches are multi-speed, versatile
network devices combining both standard and "Big-Pipe" ports
under the same hood.
2.1 Key Features
• Compliant with IEEE802.3 and 802.3u standards for
100Base-TX/FX.
• 16-port Fast Ethernet Switch, pure 10/100Base-TX
• Wire-speed "Store-and-Forward" filtering/forwarding
eliminates bad data packets with minimal delay
• 100Base-TX ports automatically sense and set optimal
line speed from 10/20, 100/200Mbps, All 100Base-TX port
support Auto-Negotiation function
• Optional Fiber-optic module for 100Base-FX, shared with
port16. DIP switch for Half/Full-Duplex selection
• Shared buffer memory and up to 8K-entry MAC source
address table make for fast handling of data packets
• Flow control to eliminate packets loss
• Internal, full-range power supply suitable for worldwide
use
• Console port for switch basic management
• Either VLAN or Turnk port support managed via console
• Up to 15 port-based VLAN support
• Up to 6 trunk support for up to 1200Mbps bandwidth
FNSW-1600S User’s Guide
7
2.2 Front Panel
FNSW-1600S
Figure 1: Front View of the FNSW-1600S
2.2.1 Ports Speed
n
100Base-TX
All 100Base-TX ports come with auto-negotiation capability.
They automatically support 100Base-TX and 10Base-T
networks. Users only need to plug a working network device
into one of the 100Base-TX ports, then turn on the hub. The
port will automatically runs in 10Mbps, 20Mbps, 100Mbps or
200Mbps after the negotiation with the connected device.
Port speed adjustment is also available through console port.
n
100Base-FX
The port 16 can be a 100Base-FX fiber-optic port as the
extension module installed (rear) At the mean time, the RJ45 port of #16 will being disabled. The Half-/Full-Duplex is
selectable by the DIP-switch on the module. Please refer to
the installation guide of the extension module for more.
2.2.2 Cabling
NOVASwitch 100Base-TX ports use RJ-45 sockets -- similar to
phone jacks -- for connection of unshielded twisted-pair cable
(UTP). The IEEE 802.3u Fast Ethernet standard requires
Category 5 UTP for 100Mbps 100Base-TX. 10Base-T networks
can use Cat.3, 4, or 5 UTP (see table A below)
8
PLANET NOVASwitch series
Port Type Cable Type Connector
10Base-T
100Base-TX
100Base-FX*
Table A: Supported port list
Cat 3, 4, 5 RJ-45
Cat.5 UTP only RJ-45
62.5/125µm multi-mode fiber
ST / SC
15 16
2.2.3 MDI Switch
11 12
Each numbered port of NovaSwitch FNSW-1600S are MDI-X
port, you can direct use straight cable for the connection to your
end nodes. However, port#12 is with one push button. To push
the button to convert the port to MDI-II port for direct hub
cascade. Please also refer to Section “RJ-45 Pin Assignment”
for more.
2.2.4 Status LEDs
One green LED to show power On/Off is on the front panel, and one
“Module Installed” LED indicator to indicate the rear open slot is
installed with a fiber-optic module. Also, each port has three status
LED indicators, as shown below.
LABEL
UPPER
ROW
MIDDLE
ROW
LOWER
ROW
FNSW-1600S User’s Guide
STATUS /
COLOR
Steady
Amber
Blink
Amber
Steady
Green
Blink
Green
Steady
Green
MEANING DESCRIPTION
FDX
Lit to indicate Full-Duplex mode
detected on that port
COL
Blinks if a collision is detected
when the port is in Half-Duplex
mode.
Link
Lit to indicate that a valid physical
UTP/STP connection is detected
Activity Blink to indicate the port is
receiving data packets
100M
Lit to indicate that a valid physical
UTP/STP connection exists on
that port runs in 100Mbps
Reset
9
OFF
10M Remains off and Link ON to
indicate the port runs in 10Mbps
Table B: FNSW-1600S Port-LED Functions
2.3 The Rear Panel
Figure 2: Rear View of FNSW-1600S
2.3.1 Extension Slot
The Switch port #16 can be a 100Base-FX switching port as the
extension module installed. As the module installed, the port#16 on
the front panel will be disabled.
Please refer to the Installation Guide of the module for the detailed
installation and settings.
NOTE: While powering on, The Switch detects the DIP-
switch status of the module, then shown on the
front panel LED indicators
2.3.2 Power Connector
The Power Connector is designed to be used with the power
cord included in the product package. Attach the female end of
the cord to the power connector and the male end of the cord to
a grounded power outlet. The accepted power range is from
100VAC to 240VAC, 50/60Hz.
2.3.3 Fan
All computing and communications devices work best when not
overheated. Please keep the fan area clear so that the cooling
function is not impaired.
10
PLANET NOVASwitch series
Loading...