Planet Technology FGSW-4840S User Manual
48-10/100Mbps + 4G Ethernet
Web Smart Switch
FGSW-4840S
User’s Manual
Trademarks
Copyright PLANET Technology Corp. 2004.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
Revision
PLANET Web Smart Gigabit Ethernet Switch User's Manual
FOR MODELS: FGSW-4840S
Part No.: EM_FGSW4840Sv1
2
TABLE OF CONTENTS
1. INTRODUCTION .............................................................................................……………………1
1.1 PACKAGE CONTENTS ...................................................................................................................................................1
1.2 HOW TO USE THIS MANUAL ..........................................................................................................................................1
1.3 PRODUCT FEATURES....................................................................................................................................................1
1.4 PRODUCT SPECIFICATIONS ...........................................................................................................................................2
2. INSTALLATION ............................................................................................................................3
2.1 PRODUCT DESCRIPTION ...............................................................................................................................................3
2.1.1 Product Overview...............................................................................................................................................3
2.1.2 FGSW-4840S Front Panel..................................................................................................................................3
2.1.3 LED Indicators....................................................................................................................................................3
2.1.4 FGSW-4840S Rear Panel..................................................................................................................................4
2.2 INSTALLING A FGSW-4840S........................................................................................................................................4
2.2.1 Desktop Installation............................................................................................................................................4
2.2.2 Rack Mounting ...................................................................................................................................................5
3. CONFIGURATION........................................................................................................................6
3.1 PREPARING FOR CONFIGURATION ..................................................................................................................................6
3.1.1 Install the Web Switch utility...............................................................................................................................6
3.1.2 Configure the FGSW-4840S.............................................................................................................................18
4. SWITCH OPERATION................................................................................................................33
4.1 ADDRESS TABLE........................................................................................................................................................33
4.2 LEARNING .................................................................................................................................................................33
4.3 FORWARDING & FILTERING .........................................................................................................................................33
4.4 STORE-AND-FORWARD...............................................................................................................................................33
4.5 AUTO-NEGOTIATION...................................................................................................................................................33
5.TROUBLESHOOTING.................................................................................................................34
APPENDIX A ..................................................................................................................................35
A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS............................................................................................................................35
A.2 10/100MBPS, 10/100BASE-TX..................................................................................................................................35
A.3 RJ-45 CABLE PIN ASSIGNMENT ...................................................................................................................................35
3
1. INTRODUCTION
1.1 Package Contents
Check the contents of your package for followi ng parts:
● Web Smart Gigabit Ethernet Switch x1
● CD-ROM user's manual x1
● Quick installation guide x1
● 19” rack mounting kit x1
● Power cord x1
● Rubber feet x 4
If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the
original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
1.2 How to Use This Manual
This 48-10/100Mbps+4G Ethernet Web Smart Switch User Manual is structured as fo llo ws:
Section 2, Installation
It explains the functions of FGSW-4840S and how to physically install the FGSW-4840S.
Section 3, Configuration
It contains information about the Smart function of FGSW-4840S.
Section 4, Switch operation
It contains specifications of FGSW-4840S.
Section 5, Troubleshooting
It contains troubleshooting guide of FGSW-4840S.
Appendix A
It contains cable information of FGSW-4840S.
In the following section, the term “Switch” means the FGSW-4840S; term of “switch” can be any third part switches.
1.3 Product Features
Complies with IEEE802.3, 10Base-T, IEEE802.3u, 100Base-TX and IEEE802.3ab, 1000Base-T
48-port 10/100Mbps Ethernet ports
2 10/100/1000Mbps ports and 2-SFP mini-GBIC interfaces
Features Store-and-Forward mode with wire-speed filtering and forwarding rates
Hardware based 10/100Mbps, half/full duplex and 1000Mbps full duplex mode, flow control and auto-negotiation
IEEE802.3x flow control for full duplex operation and backpressure for half duplex operation
Integrated address look-up engine, support 4K absolute MAC addresses
Remote Web management interface
System log, view trap, firmware upgrade, IP setting through the Web Switch utility
Port-based VLAN, Trunk, QoS support
Supports backup and restore current configuration
Trap function for Switch events
Automatic address learning and address aging
Supports Auto-MDI/MDI-X function
1
Support CSMA/CD protocol
100~240VAC, 50~60Hz universal Power input
FCC, CE class A compliant
1.4 Product Specifications
Model FGSW-4840S
Hardware Specification
10/100Base-TX ports 48
10/100/1000Mbps ports 2
SFP-Mini-GBIC interfaces 2
Switch architecture Store-and-Forward
Switch Fabric 17.6Gbps
Switch throughput 13Mpps
Address Table 4K entries
Share data Buffer 1536KBytes
Flow Control Back pressure for half duplex, IEEE 802.3x Pause Frame
Dimensions (mm) 440 x 200 x 44 mm (1U height)
Weight 3kg
Power Requirement 100-240V AC, 50-60 Hz
Power Consumption 24 watts, 81 BTU
Standards Conformance
Network Standards IEEE 802.3 (Ethernet),
Operating Temperature 0~50ºC
Storage Temperature -40~70ºC
Humidity 5% to 90% (Non-condensing)
Regulation Compliance FCC Part 15 Class A, CE
for full duplex
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE 802.3z (Gigabit Ethernet)
IEEE 802.3x (Full-duplex flow control)
2
2. INSTALLATION
This section describes the functionalities of FGSW-4840S’s components and guides how to install it on the desktop or shelf.
Basic knowledge of networking is assumed. Please read this chapter completely before continuing.
2.1 Product Description
The PLANET FGSW-4840S is a 10/100/1000Mbps Ethernet Switch provides 48 10/100Base-TX ports respectively with 2
10/100/1000Base-T ports and 2-SFP Mimi-GBIC interfaces. With a 17.6Gbps internal switching fabric, the FGSW-4840S
can handle extremely large amounts of data in a secure topology linking to a backbone or high capacity servers. The
FGSW-4840S has a 4K MAC Address table and provides a 1536KBytes frame buffer. The FGSW-4840S offers wire-speed
packet transfer performance without risk of packet loss. The high data throughput of these devices make them ideal for
most Gigabit environments, especially network upgrades to a Gigabit environment.
The additional Web Switch utility allows access Web interface of FGSW-4840S. Smart function such as per port speed,
duplex, flow-control and QoS settings, Trunking , port-based VLAN.
2.1.1 Product Overview
PLANET FGSW-4840S is a Web Smart Gigabit Ethernet Switch with 48 Fast Ethernet ports and 2 Gigabit Ethernet ports
support 10/100Mbps and 10/100/1000Mbps Auto-Negotiation for optimal speed detection through RJ-45 Category 6, 5 or
5e cables. Also, all the ports support Auto-MDI/MDI-X that can detect the type of connection to any Ethernet device without
requiring special straight or crossover cables. The FGSW-4840S also provides 2 SFP Mini-GBIC interfaces for fiber
extension to uplink to a server or a network backbone.
This products also supports store-and-forward forwarding scheme to ensure low latency and high data integrity, eliminates
unnecessary traffic and relieves congestion on critical network paths. With an intelligent address recognition algorithm,
FGSW-4840S could recognize up to 4K different MAC address and enables filtering and forwarding at full wire speed.
2.1.2 FGSW-4840S Front Panel
Figure 2-1 shows a front panel of FGSW-4840S.
Figure 2-1 PLANET FGSW-4840S Front Panel
Note:
To press and release the RESET button. The FGSW-4840S will back to the factory default
mode. Be sure that you backup the current configuration of FGSW-4840S; else the entire
configuration will be erased when pressing the “RESET” button.
2.1.3 LED Indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
SYSTEM Green Lights and blinking to indicate the CPU is working.
Per 10/100Mbps port
LED Color Function
LNK/ACT Green
Lit: indicate the link through that port is successfully established.
Blink: indicate that the switch is actively sending or receiving data over that port.
3
Per 1000Base-T port
LED Color Function
LNK/ACT Green
SPEED Green/orange
Lit: indicate the link through that port is successfully established.
Blink: indicate that the switch is actively sending or receiving data over that port.
Green: indicate that the port is operating at 1000Mbps.
Orange: indicate that the port is operating at 100Mbps.
Per SFP-Mini-GBIC port
LED Color Function
LNK/ACT Green
Lit: indicate the link through that port is successfully established.
Blink: indicate that the switch is actively sending or receiving data over that port.
2.1.4 FGSW-4840S Rear Panel
The rear panel of the Switch indicates an AC inlet power socket, which accepts input power from 100 to 240VAC,
50-60Hz.
100~240V AC
50/60 Hz
Figure 2-2 Rear Panel of FGSW-4840S
Power Notice:
1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the
time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent y ou from network data loss
or network downtime.
2. In some area, installing a surge suppression device may also help to protect your switch from being damaged by
unregulated surge or current to the Switch or the power adapter.
2.2 Installing a FGSW-4840S
This section describes how to install your FGSW-4840S Web Smart Gigabit Ethernet Switch and make connections to the
switch. Please read the following topics and perform the procedures in the order being presented. PLANET FGSW-4840S
Web Smart Gigabit Ethernet Switch do not need software configuration. To install your FGSW-4840S on a desktop or shelf,
simply complete the following steps.
2.2.1 Desktop Installation
To install an FGSW-4840S on a desktop or shelf, simply complete the following steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the switch.
Step2: Place the FGSW-4840S on a desktop or shelf near an AC power source.
Step3: Keep enough ventilation space between the Switch and the surrounding objects.
Note:
Step4: Connect your FGSW-4840S to network devices.
A. Connect one end of a standard network cable to the 10/100 or 10/100/1000 RJ-45 ports on the front of the
FGSW-4840S
B. Connect the other end of the cable to the network devices such as printer servers, workstations or routers…etc.
Note:
When choosing a location, please keep in mind the environmental restrictions discussed in
Chapter 1, Section 4, Specification.
Connection to the Switch requires UTP Category 5 network cabling with RJ-45 tips. For more
information, please see the Cabling Specification in Appendix A.
4
Step5: Supply power to the Switch.
A. Connect one end of the power cable to the FGSW-4840S.
B. Connect the power plug of the power cable to a standard wall outlet.
When the FGSW-4840S receives power, the Power LED should remain solid Green.
2.2.2 Rack Mounting
To install the switch in a 19-inch standard rack, follow the instructions described below.
Step1: Place your FGSW-4840S on a hard flat surface, with the front panel positioned towards your front side.
Step2: Attach a rack-mount bracket to each side of the Switch with supplied screws attached to the package. Figure 2-3
shows how to attach brackets to one side of the Switch.
Figure 2-3 Attaching the brackets to the FGSW-4840S
Caution:
You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws
would invalidate your warranty.
Step3: Secure the brackets tightly.
Step4: Follow the same steps to attach the second bracket to the opposite side.
Step5: After the brackets are attached to the Switch, use suitable screws to securely attach the brackets to the rack, as
shown in Figure 2-4
Figure 2-4 Mounting the Switch in a Rack
Step6: Proceed with the steps 4 and steps 5 of session 2.2.1 Desktop Installation to connect the network cabling and
supply power to your Switch.
5
3. CONFIGURATION
Unlike the unmanaged switch (Dumb switch), FGSW-4840S performs series smart functions that make the Switch operate
more effectively. This Chapter will describe the common usage of the Switch’s Smart Configuration.
3.1 Preparing for configuration
When you are ready to configure the smart functions of the Web Smart Gigabit Ethernet Switch. Please install the Web
Switch utility and it can easily list the FGSW-4840S in your Ethernet environment.
This Web Switch Utility allows assigning an IP address or password change and firmware upgrade for the FGSW-4840S.
You can easily configure the FGSW-4840S’s Smart function through the Web browser. Such as per port speed, duplex, flow
control, QoS settings, Trunking and port-based VLAN.
3.1.1 Install the Web Switch utility
The following install instructions guiding you through the installations of the Web Switch utility.
1. Insert the attached user’s manual CD in the CD-ROM Drive.
2. The CD-ROM drives to initiate auto run program. Once, completed. The screen in Figure 3-1 appears.
Figure 3-1 Web Switch Utility location
3. Press the Web Switch Utility and follow the on-screen instructions to install the utility. The install procedures in following
screens appear.
6
Figure 3-2 Web Switch Utility install process
Figure 3-3 Web Switch Utility install process
7
Figure 3-4 Web Switch Utility install process
Figure 3-5 Web Switch Utility install process
8
Figure 3-6 Web Switch Utility install process
Figure 3-7 Web Switch Utility install completed
4. After install completed, choose Program Files -> PLANET Web Switch and execute the Web Switch utility. The screen
in Figure 3-8 appears.
9
Loading...