Planet Technology DVR-400 User Manual

Digital Video Recorder
DVR-400
Users manual
1
Copyright
The products and programs described in this Users Manual are licensed products of PLANET Technology, This User s
Manual contains proprietary information protected by copyright, and this Users Manual and all accompanying hardware,
software, and documentation are copyrighted.
No part of this Users Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic medium
or machine-readable form by any means by electronic or mechanical. Including photocopying, recording, or information
storage and retrieval systems, for any purpose other than the purchaser's personal use, and without the prior express
written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and
makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this Users Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this Users Manual. PLANET
makes no commitment to update or keep current the information in this Users Manual, and reserves the right to make
improvements to this Users Manual and/or to the products described in this User s Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
Regulatory
FCC Certification
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference a
the own expense.
CE Mark
This product is marked with the CE symbol and indicates compliance with all applicable directives.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and
software products by their trade names. In most, if not all cases, their respective companies claim these designations as
trademarks or registered trademarks.
2
Revision
Users Manual for PLANET Digital Video Recorder
Model: DVR-400
Rev: 1.0 (Oct. 2004)
Part No. EM-DVR400V1
3
Table of Contents
Chapter 1 Introduction..................................................................................1
Overview......................................................................................................................1
DVR Functions......................................................................................................1
Package Content.........................................................................................................2
Physical Details...........................................................................................................2
Buttons Definitions................................................................................................2
Physical Interfaces................................................................................................4
Chapter 2 Preparations & Installation..........................................................5
Installing and Configuring DVR-400..........................................................................5
On-Screen Display......................................................................................................9
Administration Interface...........................................................................................10
OSD (On Screen Display) administration............................................................10
Chapter 3 DVR- 400 Menu Setup................................................................12
Introduction...............................................................................................................12
MAIN MENU........................................................................................................12
CAMERA SELECT..............................................................................................13
RECORD SELECT..............................................................................................14
VIDEO RECORDING MODE..............................................................................14
RECORD FRAMRATE........................................................................................15
VIDEO QUALITY.................................................................................................16
RECORD SCHEDULE........................................................................................17
SUB MENU.........................................................................................................18
PASSWORD CHANGE .....................................................................................18
TIME SET ......................................................................................................19
DATE DISPLAY FORMAT ..................................................................................19
HDD SETUP.......................................................................................................20
SENSOR SETUP................................................................................................20
How to enable the Motion detection recording in DVR-400.................................21
NETWORK SETUP.............................................................................................22
PLAYBACK Configurations......................................................................................23
CONTROL BUTTONS.........................................................................................23
Chapter 4 DVR-400 Client Utility Administration.......................................25
DVR-400 client utility.................................................................................................25
Procedures of DVR Client utility..........................................................................25
Appendix A Specifications..........................................................................29
4
Chapter 1
1
Introduction

Overview

The DVR-400 (Digital Video Recorder) is for recording/retrieving video streams from up to 4 channels at the
same time. It adopts cutting-edge digital image compression technology to compress the analog input
channel video streams, and uses HDD to record the compressed video stream.
The following operation guide explains how to operate/manage the DVR-400, and the following installation guide explains how to complete the first DVR-400 installation on your side.

DVR Functions

· High quality M-JPEG compression
· Video loop through
· Real-time 4 concurrent cameras recording
· MAX. 120 FPS video displaying rate
· Motion detection / video lost buzzer
· Matured embedded system remote monitoring and control of DVR
· 4 alarm input for various application
· Swappable HD / Max. 250 GB HD support
· Scheduled/event/continuous recording
1

Package Content

The contents of your product should contain the following items:
DVR-400 unit
Power adapter
Screws for swappable HDD tray
Keys for swappable HDD tray
Quick installation guide
Users manual CD

Physical Details

Front Panel of DVR-400
Rear Panel of DVR-400

Buttons Definitions

The following are the introductions of DVR-400 front panel buttons. The definitions of the front are shown
below:
2
· MENU: press to display Operation menu option
ë
When stopping video recording; it is required to enter the
· SELECT: press to change menu field
· ENTER: press to change the setting value or enter into a sub menu
· RECORDING: press to start recording.
· STOP (recording/playback): press stop video recording/playback
Note
· FAST FORWARD: press to play the recorded stream faster.
· PLAYBACK: press to start playback
· PAUSE: press to pause the video playback
· REVERSE: press to playback backward
· CHANNEL 1: press to select video source on channel 1
· CHANNEL 2: press to select video source on channel 2
· CHANNEL 3: press to select video source on channel 3
· CHANNEL 4: press to select video source on channel 4
· ALL CHANNELS: press to select all channels display
authorization password. The default value is 111111
When entering or modifying password, the button definitions are shown below:
Button definition when entering password
means 1 ‚ means 6
means 2 8 means 7
means 3 7 means 8
means 4 ; means 9
5 means 5 8 means 0
3

Physical Interfaces

1 3
2 5 6 7 8 9 10 11
Physical conection interface of DVR-400 are shown and explained in the following descriptions.
4
1. S-Video:
2. Video output:
3. Monitor: Second Video output.
4. Video input: Connect your standard video cameras to these inputs.
5. Video loop-through: These outputs provide loop-through connections, and can be used for direct
monitoring of the connected video cameras.
6. Sensor input/alarm output: 4 sensor inputs and one alarm output.
7. NTSC/PAL switch:
8. DC-in (12Voltage): Connect the power cable here.
9. Audio input/output:
10. LAN: 10/100 Ethernet via the RJ-45 socket.
11. Power switch: This switch should only be used after shutting down the unit correctly with the help of the
Power button on the front panel.
4
Chapter 2
2
Preparations & Installation

Installing and Configuring DVR-400

STEP1:
Please power off the DVR-400 and unlock the DVR-400 swappable HDD tray
STEP2:
Remove the harddisk tray cover; connect your harddisk securely with the DC power cable and IDE
cable in the harddisk tray. Make sure the installed HDD is set to Master and secure the HDD
using the original HD screws or the screws in the DVR-400 accessory pack.
Place and lock the HDD tray to DVR-400. Power on the DVR-400, the
DVR-400 will now automatically detect and format the new disk(s).
5
ë
Please be sure to finish the hard disk drive installation
before using the DVR. The Maximum HDD capacity support is
ë
two BNC connector for video
Note
250GB.
STEP3:
Please connect TV (monitor) to the Video output connector in the rear panel.
Note
DVR-400 provides one S-Video and
output.
STEP4:
Please use standard analog video cameras to connect to the DVR400. The DVR-400 equipped 4
BNC connectors on the rear panel for video input.
Physical camera installation with DVR-400 is shown as below:
l Connect the camera signal line to video input on DVR-400
l Power on camera, and you may now check the video on the screen.
Video Input connection (TV or monitor)
DVR-400 provides 4 x BNC connectors for video source input.
6
CheckingOK
STEP5:
Please ensure DVR-400 is power OFF before commencing, and check the power supply status.
Use standard RJ-45 cables to connect the LAN port on DVR-400.
Connect the supplied Power Adapter and power on machine.
The PWR LED Indicator should be Green during normal operation
After powering on the DVR-400, it will check HDD for several seconds; the information will be
displayed on the monitor:
HDD Checking
MASTER HARD DRIVE
[HDD Model number]
HDD CheckingOK
LAN CheckingOK
Audio
After the internal checking completed, DVR-400 will enter into real-time display mode, the images
on the connected camera will be displayed in real-time.
CH1
CH2
CH3 CH4
7
Sensor Installation
The unit provides 4 sensor input for 4 channels. The sensor Installation procedures are as follows.
For the installation of the sensors:
STEP1: Connect the sensor signal line to the alarm signal terminal is at the units back panel
STEP2: Connect the video signal line to the unit. The Sensor signal terminal is at the units back panel
STEP3: Connect the sensor adaptor jack into the sensor, and plug in the adaptor.
CH1 CH2 CH3
Alarm installation
The unit provides 1 internal switch for sounding alarm when the sensor is activated due to the unwanted
entrance of anonymous visitor. The switch is open at normal state, but, when the alarm is activated, the switch
is closed So that the alarm gets the power. The circuitry is shown as above figure. There are two simple steps
CH4
Alarm out
for the installation of the alarm
i. Prepare the power supply: the alarm needs a power supply; the power supply comes with the alarm
ii. Connect the alarm power line: the alarm power line is connected to the alarm switch terminal.
8

On-Screen Display

Press
&
button to
Power on the system
CH1
CH3
Press
&
button to
OSD Mode Display
Press
n
button to stop
recording (password is
open OSD menu as right
CH1 CH2 CH3 CH4
exit OSD menu to real-time display
CAMERA SELECT 1234 RECORD SELECT 1234 RECORD MODE EACH RECORD FRAMERATE 30 VIDEO QUALITY MORRMAL RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT)
MAIN MENU
Press l button to start recording
requested!)
Recording Mode Display
CH3 CH4
Press button to search
time or event to playback
04/03/24 13:24:21-04/03/24 13:44:54
Press & button to exit the menu
(Ù,Ú) MOVE, (SELECT) CHANGE (PLAY) PLAY (MENU) EXIT (>>) SELECT EVENT OR
SEARCH TIME
HDD DRIVE: MASTER
>01 TIME 04/09/24 13:24:21 02 TIME 04/09/24 13:30:55 03 TIME 04/09/24 13:40:54 04 TIME 04/09/24 13:45:14 05 TIME 04/09/24 13:50:34
SEARCH MODE
Press button
Press n button to stop playback
CH1 CH2 CH3 CH4
PLAYBACKMODE
9
10

Administration Interface

M
AIN MENU
M
AIN MENU
PLANET DVR-400 provides OSD menu for machine management and administration.
CAMERA SELECT 1234 RECORD SELECT 1234 RECORD MODE EACH RECORD FRAMERATE 30 VIDEO QUALITY MORRMAL RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT

OSD (On Screen Display) administration

PLANET DVR-400 connects with two default IP addresses, and default IP address is 192.168.0.20. You may
use any PC to connect to the LAN port of DVR-400 to start machine administration.
CAMERA SELECT 1234 RECORD SELECT 1234 RECORD MODE EACH RECORD FRAMERATE 30 VIDEO QUALITY MORRMAL RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP
Ø NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
NETWORK MENU
ACCEPT CLIENT [YES]
MAC ADDRESS 00:30:4F:09:78:52
IP ADDRESS 192.168.000.020
SUBNET MASK 255,255,255,000
GATEWAY 192.168.000.254
PRESS (Ù,Ú), HEN (SELECT)
PRESS (MENU) TO EXIT
The LAN information Parameter Description of DVR-400
ë
In the first installation, it is suggested to locate your
.
If youre not familiar with TCP/IP, please refer to related
ACCEPT CLIENT YES / NO
Default: YES
MAC MAC address of DVR-400
Default:
IP LAN IP address of DVR-400
Default: 192.168.000.020
SUBNET MASK LAN mask of DVR-400
Default: 255.255.255.000
GATEWAY Gateway of DVR-400
Default: 192.168.000.254
Note
PC in the same network segment (192.168.0.x) of DVR-400
chapter on users manual CD or consult your network administrator for proper network configurations.
11
12
Chapter 3
3
M
AIN MENU
ë
Please stop recording or playback before you enter into OSD
menu. You will be requested to enter machine admin password
DVR- 400 Menu Setup

Introduction

The DVR-400 OSD menu provides ease-of-use machine configurations; please press the MENU button of the
front panel, then the OSD menu will appear with a cursor over the first item. The cursor can be moved by the
up and down buttons.

MAIN MENU

Please press & button to display main menu optin shown as below figure
CAMERA SELECT 1234 RECORD SELECT 1234 RECORD MODE EACH RECORD FRAMERATE 30 VIDEO QUALITY MORRMAL RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
Operation Buttons
& --- Press to display menu option.
pq --- Press to change menu field or change the units configuration values.
8 --- Press to select menu item or confirm the selection.
Note
to stop recording.
13

CAMERA SELECT

Channel Display Control
Channel 1 button: Full screen display of channel 1
Cha
nnel 2 button: Full screen display of channel 2
Channel 4 button: Full screen display of channel 4
Channel 3 button: Full screen display of channel 3
M
AIN MENU
ë
mode, you can use the following buttons to display
ë
in
The DVR-400 provides 4 camera inputs. Please use channel buttons on the front panel to select specified
channel for real-time display.
Please use SELECT button or CHANNEL buttons for different combinations for channel display.
Example:
Ø CAMERA SELECT 1 - - -
RECORD SELECT 1 - - ­RECORD MODE EACH RECORD FRAMERATE 30 VIDEO QUALITY MORRMAL RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
a) When you choose (----), all cameras are off
b) When you choose (1234), video content in all cameras will be displayed.
c) When you choose (1---), only the content of channel 1 will be displayed.
Note
Note
While no video connection or connection failure, VIDEO LOSS” signal will be displayed, and the built- alarm buzzer will be triggered to sound.
Channel Display Control In ”EACH Full-screen format of each channel.
In EACH mode, you can use the following buttons to display Full-screen
format of each channel.
14

RECORD SELECT

M
AIN MENU
M
AIN MENU
Please select desired video channel on this menu: the machine operation is same as CAMERA SELECT
options.
Only the video in the selected camera will be recorded in DVR-400 harddisk
CAMERA SELECT 1 - - -
Ø RECORD SELECT 1 - - -
RECORD MODE EACH RECORD FRAMERATE 30 VIDEO QUALITY MORRMAL RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT

VIDEO RECORDING MODE

DVR-400 provides 4 camera inputs. You can use channel buttons on the front panel to select specified
channel/camera for real-time video display and recording.
There are two kinds of recording mode: EACH mode (full screen mode) and QUAD screen mode. When you
set to EACH mode, you can view the full-screen display of one specified channel.
When you set to QUAD mode, quad-screen (4-camera) will be displayed.
Please use Ù,Ú buttons of front panel to select mode and then enter 8 button to confirm the selection
CAMERA SELECT 1 - - ­RECORD SELECT 1 - - -
Ø RECORD MODE EACH
RECORD FRAMERATE 30 VIDEO QUALITY MORRMAL RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
15
M
AIN MENU
ë
he record frame rate is, the more natural look
But the lower the record frame rate is, the more you can
save the space on HDD. The following is the recording fps

RECORD FRAMRATE

There are 9 different frame rate settings for operation: 30fps, 15fps, 10fps, 7fps, 5fps, 4fps, 3fps, 2fps, and
1fps. (Factory default setting: 30fps)
Please use Ù,Ú buttons of front panel to select mode and then enter 8 key to confirm the selection
Note
Frame/Second 1 2 3 4 5 7 10 15 30
CAMERA SELECT 1 - - ­RECORD SELECT 1 - - ­RECORD MODE EACH
Ø RECORD FRAMERATE 30
VIDEO QUALITY MORRMAL RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
RECORDING FRAME RATE TABLE
The higher t will be displayed on the screen when playing back.
table for your reference.
1CH 1 2 3 4 8 7 10 15 30
EACH
MODE
QUAD MODE 1 2 3 4 5 7 10 15 30
2CH 0.5 1 1.5 2 2.5 3.5 5 7.5 15
3CH 0.33 0.67
4CH 0.25 0.5 0.75
1 1.33 1.7 2.33 3.33
1 1.25 1.75 2.5 3.75 7.5
5 10
16

VIDEO QUALITY

M
AIN MENU
ë
he higher the video quality is, the clearer images the unit
plays. But the lower the video quality is, the more you can
save the space on HDD. The following is the recording time
There are 3 different video quality settings for operation: Normal, Low, and High
Please use Ù,Ú buttons on the front panel to select video recording quality and then press the enter 8 key to
confirm the selection
Note
Frame/Second 1 2 3 4 5 7 10 15 30
CAMERA SELECT 1 - - ­RECORD SELECT 1 - - ­RECORD MODE EACH RECORD FRAMERATE 30
Ø VIDEO QUALITY NORMAL
RECORD SCHEDULE SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
DIFFERENT VIDEO QUALITY SETTINGS ON HDD CAPACITY
T
vs video quality settings table for your reference.
EACH
MODE
QUAD
MODE
HI 733 366 244 183 146 184 73H 48H 25H
NORMAL 992 496 331 248 192 141 99H 66H 33H
LO 115 576 384 288 238 153 115 76H 39H
HI 556 279 185 139 111 80H 56H 37H 19H
NORMAL 763 382 255 190 152 110 76H 51H 25H
LO 877 438 292 228 175 125 88H 58H 29H
The recording hours on 80GB HDD
17

RECORD SCHEDULE

M
AIN MENU
RECORD SCHEDULE menu in DVR-400 provides changing a recording schedule/type to meet the various
surveillance application demands.
CAMERA SELECT 1 - - ­RECORD SELECT 1 - - ­RECORD MODE EACH RECORD FRAMERATE 30 VIDEO QUALITY NORMAL
Ø RECORD SCHEDULE
SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
Time format in DVR-400 schedule video recording is 24-hour format.
(T) Letter indicates recording.
(S) Letter indicates sensor recording. It means the unit starts recording as the attached sensors being
triggered during this period.
(--) Recording is off during this duration.
PROGRAMMED RECORD
| | | | | | | | |
+TTTTTTTTTTTTTTTTTTTTTTTT+
0 3 6 9 12 15 18 21 24
T: TIME S: SENSOR _--: NONE
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
SETTING EXAMPLE:
00:00 ~ 7:00 SENSOR RECORDING
07:00 ~11:00 RECORDING DISABLED
11:00 ~18:00 RECORDING
18:00 ~24:00 SENSOR RECORDING
+ S S S S S S ; ; ; ; T T T T T T T S S S S S S S +
| | | | | 0 6 11 18 24
18

SUB MENU

ë
puts, which can be configured
motion detection+NO over “SENSOR SETUP” menu option. After
Note
SENSOR RECORDING INSTALLATION
The unit provides 4 alarm in as normal close, normal open, motion detection +NC and
the sensor configuration, please go back to RECORD SCHEDULE menu to enable sensor recording.
SUB MENU
SUB MENU provides the flexibility of changing machine admin password, time /date setting, date format.
Ø PASSWORD CHANGE TIME SET AUDIO RECORD [ON] AUDIO MUTE [OFF] DATE DISPLAY MODE YYYY/MM/DD
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
PASSWORD CHANGE
When entering PASSWORD CHANGE menu; a password change input menu will be displayed on screen
(note: machine default password is 111111)
When the new password is configured and accepted, DVR-400 will prompt message:
PASSWORD changed!!!
CURRENT PASSWORD: -------
NEW PASSWORD: -------
CONFIRM PASSWORD: --------
19
The message will blink 5 times. Then the display goes back to SUB MENU.
SUB MENU
If the password was not accepted, DVR-400 will automatically return to SUB MENU.
FRONT PANEL BUTTONS DEFINITION
means 1 ‚ means 6
means 2 8 means 7
means 3 7 means 8
means 4 ; means 9
5 means 5 8 means 0
TIME SET
TIME SET menu offers DVR-400 date and hour.modification, the time and date settings will affect the recoded
video files as well.
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
TIME
04/10/10 12:35:23
DATE DISPLAY FORMAT
DVR-400 provides yyyy/mm/dd or dd/mm/yyyy format for time display to meet application demands.
PASSWORD CHANGE TIME SET AUDIO RECORD [ON] AUDIO MUTE [OFF] Ø DATE DISPLAY MODE YYYY/MM/DD
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
20

HDD SETUP

HARD DRIVE SETUP

SENSOR SETUP

OVERWRITE ENABLED:
If you choose YES, DVR-400 will continue recording and overwrite the recorded data when HDDs space is
full
If you choose NO, the unit will stop recording while HDDs space is full
MASTER HDD SIZE:
Display the capacity of the installed HDD in DVR-400
MASTER HDD USED:
Display the percentage of HDDs capacity has been used
MASTER HDD FORMAT:
Erases all the recorded data in harddisk
The machine admin password is required before formatting, after the unit formatted, the message HARD
DISK FORMATTED” will appear on the screen.
SENSOR SETUP
OVERWRITE ENABLED [YES] MASTER HDD SIZE 40000MB MASTER HDD USED 0MB 0% MASTER HDD FORMAT SLAVE HDD SIZE N/A SLAVE HDD USED N/A SLAVE HDD FORMAT
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
SENSOR RECORD TIME 05 ALARM OUT TIME 00
CHANNEL-1 TYPE: NORMAL -OPEN CHANNEL-2 NOT INSTALLED CHANNEL-3 NOT INSTALLED CHANNEL-4 NOT INSTALLED
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
SENSOR RECORD TIME:
Recording duration (in seconds) when sensor is triggered.
ALARM OUT TIME:
The ALARM TIME OUT controls how long (in second) the alarm sounds after being triggered.
SENSOR TRIGGER MODES:
21
DVR-400 provides 5 different modes to meet the various surveillance application demands:
SE
NSOR SETUP
1. Not installed.
2. Normal open.
3. Normal close.
4. Motion +N-C
5. Motion + N-O
In normal open mode, the cable line Connected between the sensor and the unit is cut off by an intruder, the
unit starts recording.
In normal close mode, the cable line Connected between the sensor and the an intruder, the unit stops
recording, cuts off unit.

How to enable the Motion detection recording in DVR-400

STEP 1:
STEP 2:
STEP 3:
SENSOR RECORD TIME 15 ALARM OUT TIME 20
CHANNEL-1 TYPE: MOTION + N-C CHANNEL-2 TYPE: MOTION + N-O CHANNEL-3 TYPE: NORMAL CLOSE CHANNEL-4 TYPE: NOT INSTALLED
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
Please go to SENSOR SETUP menu
Toggle the motion detection option.
After the selection, please browse to MAIN MENU and go to RECORD SCHEDULE menu to
enable the alarm setting, so that the motion detection video recording will operate properly.
PROGRAMMED RECORD
+TTTSSTTTTTTTTTTTTTTTTTTT+
| | | | | | | | |
0 3 6 9 12 15 18 21 24
T: TIME S: SENSOR _--: NONE
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
22

NETWORK SETUP

ë
ACCEPT IP: select YES to allow the remote access, NO to disable the machine remote management.
Note
NETWORK MENU
ACCEPT CLIENT [YES]
MAC ADDRESS 00:30:4F:09:78:52
IP ADDRESS 192.168.000.020
SUBNET MASK 255,255,255,000
GATEWAY 192.168.000.254
PRESS (Ù,Ú), THEN (SELECT) PRESS (MENU) TO EXIT
Minimum requirements for networking video playback: CPU: 1 GHZ or above System Memory: 256MB or above VGA memory: 32MB OS: Window2000/XP
23

PLAYBACK Configurations

ë
The reverse playback speed depends on the fps, the number
SEARCH TIME
ë
(PLAY)
If youd like to view the recorded video files, the front panel buttons can be used to operate various playback
functions.
Press button, then the playback time /events selection menu as the left figure appears on the screen. Or
you can simply press twice to start playing directly.

CONTROL BUTTONS

<< Rewind Playing:
Press this button to play recorded video in reverse direction.
Note
|| PAUSE Button:
Press this button to pause the playback, or to advance one single frame upon pause mode.
Playback:
Press this button to play the recorded video.
You can either enter the specified time/date to playback or select the event or even view the playback over PC
of the recorded channel, the enabled recording video quality.
HDD DRIVE: MASTER
04/03/24 13:24:21-04/03/24 13:44:54
>01 TIME 04/09/24 13:24:21
02 TIME 04/09/24 13:30:55 03 TIME 04/09/24 13:40:54 04 TIME 04/09/24 13:45:14 05 TIME 04/09/24 13:50:34
(Ù,Ú) MOVE, (SELECT) CHANGE (PLAY) PLAY (MENU) EXIT (>>) SELECT EVENT OR TIME
>> (Fast forward button):
Note
1.Please stop recording before playback.
2.To list the recorded video files, please press button to display the video files in DVR-400 local HDD storage
24
Press this button to play the recorded video in forward direction.
The unit provides three levels of fast forward playback speed:
>> 1: play one time faster (x1), press >> button.
>> 2: play two times faster (x2) than the normal play.
>> 3: play four times faster (x4) than the normal play.
n STOP: Press this button to stop playing the recorded video.
l REC:
DVR recording Hours on 40GB Hard Drive
Recording Results in NTSC format
Video Suanal
Display
Format
QUAD screen
NTSC
Full screen
Recording Results in PAL format
Display
Video Suanal
Format
QUAD screen
PAL
Full screen
Video Quality
30 fps 15 fps 7 fps 1 fps
HIGH 18 Hours 36 Hours 72 Hours 540 Hours
NORMAL 24 Hours 48 Hours 96 Hours 720 Hours
BASIC 29 Hours 58 Hours 116 Hours 870 Hours
HIGH 32 Hours 64 Hours 128 Hours 960 Hours
NORMAL 45 Hours 90 Hours 180 Hours 1350 Hours
BASIC 56 Hours 112 Hours 224 Hours 1680 Hours
25 fps 12 fps 6 fps 1 fps
Video Quality
HIGH 19 Hours 38 Hours 76 Hours 475 Hours
NORMAL 24 Hours 48 Hours 96 Hours 600 Hours
BASIC 30 Hours 60 Hours 120 Hours 750 Hours
HIGH 31 Hours 62 Hours 124 Hours 775 Hours
NORMAL 45 Hours 90 Hours 180 Hours 1125 Hours
BASIC 59 Hours 118 Hours 236 Hours 1475 Hours
25
Chapter 4
4
DVR-400 Client Utility Administration

DVR-400 client utility

This DVR-400 allows system administrator to manage machine from a remote location to view live and
recorded video over private network or the Internet connection. Also, you can capture the video from the unit
and play the stored video later on.

Procedures of DVR Client utility

· Please find the DVR_Client.exe in the Utility folder on users manual CD
· Copy the DVR utility folder to suitable folder, for example, C:\Program Files\PLANET\DVR\Utility
· Double-click the DVR_Client.exe and the main screen will be shown.
· Click on Connect option on Main window to enter into DVR Client connection manager, the following
dialog window will be shown:
26
ë
400 installed behind firewall or NAT device,
· Please insert IP address 192.168.0.20 / password: 111111 to log in the remote DVR-400.
DVR IP: IP address of the remote DVR-400.
Password: The password is same password used for formatting the DVR-400 Hard Drive. The default
value is 111111
· When successfully connected, you would see Connected sign. This window also displays DVR-400 IP
Note
address and status of connection speed.
If the DVR­please reserve ports 14337, 14338 for communication purpose.
27
The remote video content will be shown in the main menu:
DVR control
The panel shown as the following figure operates exactly as the remote DVR operational button allows you to
control remote DVR to live view, record and playback as well.
Capture & Playback
When you click REC button, it will start to record the incoming video on your PC hard disk. The DVR client
creates steam_files folder where the execution file is located. When the client is recording, the Capture &
28
Play status indicator would show the current status are Recording.
After recording is finished, click Play button to play the recorded video stream. Then you will see a stream
file list of the video stream files previously captured.
DVR management
This option enable you to just remote DVRs operation setting: Video Quality, Record Frame rate, Alarm On
Duration, Alarm record Duration, Input Channels, Record Channels, DVR system time setting and Record
Schedule. All of settings operate as you do with DVR itself. Notice: For the record mode change can be made
only on DVR, so the display shows the current DVR record mode on connection.
29
Appendix A
A
Specifications
Model DVR-400
Video Inpuit NTSC/PAL
Operating System None
Video Inpout 4ch composite
Video Output 2ch composite + S-Video
Vdieo Loop 4ch composite
Audio Input 1ch RCA
Audio Output 1ch RCA
Built-in Buzzer Yes
Display Frame 120fps (NTSC) / 100fps (PAL)
Recording Framer Rate
(Quad mode)
Recording Frame Rate
(Each mode)
Recording Mode Continuous, manual, event programed
Resolution (Display) NTSC: 720*480 / PAL: 720-576
Resolution (Recording) NTSC: 320*112, 640*224 / PAL: 320-136, 640*272
Compression Format Motion JPEG (8-20K bytes/frane)
HDD Swappable HDD tray (Max. HDD capacity: 250GB)
Search Mode Time, date, camera
Netwrok TCP/IP
Ethernet RJ45
Watch-dog Auto-recovery capability after power
Dimension 350 x 292 x 60 mm (W x D x H)
Weight 4.15 kg (gross weight)
Max. 30fps (NTSC) / Max. 25fps (PAL)
Max. 7.5fps (NTSC) / Max. 6.25fps (PAL)
Loading...