Planet Technology ADE-4100 User Manual
ADSL Modem Router
With 4-port Switch
ADE-4100
User’s Manual
Copyright
Copyright (C) 2003 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of
PLANET Technology, This User’s Manual contains proprietary information protected by
copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form by any means by electronic or
mechanical. Including photocopying, recording, or information storage and retrieval systems,
for any purpose other than the purchaser's personal use, and without the prior express
written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or
expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET
disclaims liability for any inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent
a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s Manual. PLANET makes no commitment to update
or keep current the information in this User’s Manual, and reserves the right to make improvements to this User’s Manual and/or to the products described in this User ’s Manual, at
any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would
appreciate your comments and suggestions.
FCC Compliance Statement
This equipment generates and uses radio frequency energy and if not installed and used
properly, that is, in strict accordance with the instructions provided with the equipment, may
cause interference to radio and TV communication. The equipment has been tested and
found to comply with the limits for a Class A computing device in accordance with the
specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If you suspect this
equipment is causing interference, turn your Ethernet Switch on and off while your radio or
TV is showing interference, if the interference disappears when you turn your Ethernet
Switch off and reappears when you turn it back on, there is interference being caused by
the Ethernet Switch.
You can try to correct the interference by one or more of the following measures:
w Reorient the receiving radio or TV antenna where this may be done safely.
w To the extent possible, relocate the radio, TV or other receiver away from the Switch.
w Plug the Ethernet Switch into a different power outlet so that the Switch and the receiver
are on different branch circuits.
If necessary, you should consult the place of purchase or an experienced radio/television
technician for additional suggestions.
CE mark Warning
The is a class B device, In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
ii
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to
numerous hardware and software products by their trade names. In most, if not all cases,
these designations are claimed as trademarks or registered trademarks by their respective
companies.
Revision
User’s Manual for PLANET ADSL Modem Router:
Model: ADE-4100A/ADE-4100B
Rev: 1.0 (August 2003)
Part No.: EM-ADE4100
iii
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION.................................................................................1
ADE-4100 FEATURES .............................................................................................1
Internet Access Features...................................................................................1
Advanced Functions...........................................................................................1
LAN Features.....................................................................................................2
Configuration & Management.............................................................................2
Security Features...............................................................................................2
PACKAGE CONTENTS...............................................................................................2
PHYSICAL DETAILS...................................................................................................3
Front Panel.........................................................................................................3
Rear Panel.........................................................................................................3
CHAPTER 2 INSTALLATION...................................................................................5
SYSTEM REQUIREMENTS..........................................................................................5
INSTALLATION PROCEDURE ......................................................................................5
CHAPTER 3 LOGIN AND SYSTEM STATUS..........................................................7
LOGIN......................................................................................................................7
Preparation.........................................................................................................7
Connecting to ADE-4100....................................................................................7
STATUS ...................................................................................................................9
CHAPTER 4 SYSTEM CONFIGURATION.............................................................11
OVERVIEW.............................................................................................................11
WAN CONFIGURATION...........................................................................................11
Per VC Setting..................................................................................................11
INTERNET CONNECTION SERVICES ..........................................................................12
Bridge Mode.....................................................................................................12
PPPoE, PPPoA Connection for WAN (Routing mode)....................................13
Fixed IP for WAN.............................................................................................16
Dynamic IP for WAN........................................................................................16
Other settings...................................................................................................17
LAN CONFIGURATION............................................................................................20
DHCP Setting...................................................................................................20
PPP CONFIGURATION............................................................................................21
NAT SETTINGS......................................................................................................23
VIRTUAL SERVERS.................................................................................................25
DNS CONFIGURATION ...........................................................................................27
BRIDGE FILTERING.................................................................................................27
SAVE SETTINGS.....................................................................................................28
CHAPTER 5 PC CONFIGURATION.......................................................................29
OVERVIEW.............................................................................................................29
WINDOWS CLIENTS................................................................................................29
TCP/IP Settings................................................................................................29
Internet Access................................................................................................35
MACINTOSH CLIENTS .............................................................................................36
LINUX CLIENTS ......................................................................................................36
CHAPTER 6 ADMIN PRIVILEGE...........................................................................37
WAN STATUS .......................................................................................................37
ATM STATUS ........................................................................................................37
i
TCP STATUS.........................................................................................................38
ROUTE TABLE........................................................................................................39
LEARNED MAC TABLE ...........................................................................................40
ADSL CONFIGURATION..........................................................................................41
RIP CONFIGURATION.............................................................................................41
PASSWORD CONFIGURATION..................................................................................43
MISC CONFIGURATION ...........................................................................................43
RESET TO FACTORY DEFAULT ................................................................................46
DIAGNOSTIC TEST..................................................................................................46
CODE IMAGE UPDATE.............................................................................................47
NETWORK CODE IMAGE UPDATE ............................................................................47
SYSTEM LOG .........................................................................................................47
APPENDIX A TROUBLESHOOTING.....................................................................48
OVERVIEW.............................................................................................................48
GENERAL PROBLEMS.............................................................................................48
CONFIGURATION AND INTERNET ACCESS ................................................................48
APPENDIX B SPECIFICATIONS............................................................................50
ADE-4100A/ADE-4100B......................................................................................50
ii
1
Chapter 1
Introduction
This Chapter provides an overview of ADE-4100's features and capabilities.
Congratulations on the purchasing of ADE-4100. The ADSL Modem Router will
allow multiple LAN users to share an Internet user account, via a DSL connection.
Once the ADSL Modem Router is installed and configured, the Internet is just a
click away.
Figure 1-1: ADSL Modem Router
ADE-4100 Features
ADE-4100 incorporates many advanced features, carefully designed to provide
sophisticated functions for user’s convenience while surfing in the net.
Internet Access Features
w Shared Internet Access. All users on the LAN can access the Internet
through ADE-4100, using only a single external IP Address. (Routing mode)
w Standard Compliance. ADSL-Compliant with ANSI T1.413 Issue 2, ITU
G.992.1 (G.DMT), and G.992.2 (G.lite).
w Data Transfer Rate. Data rate up to 8 Mbps downstream and up to 1 Mbps
upstream
w User Friendly Interface. Simple and intuitive graphical user interface
w Fixed or Dynamic IP Address. On the Internet (WAN port) connection,
ADE-4100A/4100B supports both Dynamic IP Address (IP Address is allocated on connection) and Fixed IP Address.
Advanced Functions
w Virtual Servers. This feature allows Internet users to access Internet serv-
ers which located on LAN side. The required setup is quick and easy.
w DMZ. One (1) PC on your local LAN can be configured to allow unrestricted
2-way communication with Servers or individual users on the Internet. This
provides the ability to run programs which demand for bi-directional communication.
1
ADE-4100 User Manual
LAN Features
w Built-in 4-port switch. Four Auto-Negotiation, Auto-MDI/MDI-X Ethernet
RJ-45 ports are used to connect office network or workstations.
w DHCP Server support. Dynamic Host Configuration Protocol provides a
dynamic IP address to PCs and other devices upon request. ADE-4100 can
act as a DHCP Server for devices on your local LAN.
Configuration & Management
w Easy Setup. Use WEB browser from anywhere to begin the configuration.
w Remote Management. PLANET ADE-4100 can be managed from any PC
on your LAN. And, if the Internet connection exists, it can also (optionally) be
configured via the Internet.
w System Diagnostic & Log: 7 layer diagnostics with links to help pages
and system event logs can greatly help network administrator solve network
problem.
Security Features
w Two-level password protected Configuration. Two-level password
protection can provided stronger protection to prevent unauthorized users
from modifying the configuration data and settings.
w NAT Protection. An intrinsic side effect of NAT (Network Address Transla-
tion) technology is that by allowing all LAN users to share a single IP address,
the location and even the existence of each PC is hidden. From the external
viewpoint, there is no network, only a single device - ADE-4100.
Package Contents
The following items should be included:
• ADE-4100 Unit
• Power Adapter
• CD-ROM containing user’s manual
• Quick Installation Guide
• RJ-45 cable
• RJ-11 cable
If any of the above items are damaged or missing, please contact your dealer
immediately.
2
Physical Details
Transmit data or receive data over Ethernet
Front Panel
Introduction
ADE-4100
LED definitions
LEDs Color Active
PWR Green
ADSL Green ON ADSL connection is established.
WAN
ACT Green
1
2
LAN
Green
3
4
Rear Panel
LAN
3
4
WAN
1
ADSL
PWR
2
ACT
ADSL Modem Router
with 4-port Switch
Figure 1-2: Front Panel
Description
The power adaptor is connected to the Mo-
ON
dem.
ON Transmit data or receive data via ADSL link.
ON
link.
9VDC
RESET
+
1234
Figure 1-3: Rear Panel
Button definition
Reset Button This button has two (2) functions:
• When pressed and released, ADE-4100 will reboot
(restart).
• When reset button is pressed over 10 seconds and
then release. ALL data will be clear and restore ALL
settings to the factory default values.
Restore Default IP Address and Clear Password
ADSL
3
ADE-4100 User Manual
If ADE-4100's IP Address or password is lost, the following procedure can be used
to recover from this situation.
Pressing the Reset button for more than 10 seconds. ADE-4100 will restore to
factory default setting. Note that this should be done only when you had tried all the
troubleshooting options. Pressing the Reset button during operation may bring you
into the risk of creating IP address conflict between your PC and the router. In such
case, you may be compelled to reboot your entire system(s).
4
2
Chapter 2
Installation
This Chapter covers the physical installation of ADE-4100.
System Requirements
• PC or TCP/IP compliant workstations
• 32 MB RAM
• Ethernet Network Interface Controller (NIC) RJ45 Port
• Internet Browser
Installation Procedure
Figure 2-1: Installation Diagram
Step 1
Choose an Installation Site
Select a suitable place on the network to install ADE-4100. Ensure ADE-4100 is
powered OFF.
Step 2
Connect LAN Cables
Use standard LAN cables to connect PCs to the LAN port on ADE-4100. Either
10BaseT or 100BaseT connections can be used.
Step 3
Connect WAN Cable
Connect one end of the RJ-11 phone cord to the LINE port on your ADSL modem.
Connect the other end of the RJ-11 phone cord to your wall phone jack.
Step 4
Power Up
5
ADE-4100 User Manual
Connect the supplied power adapter to ADE-4100 and power up.
Use only the power adapter provided. Using a different one may cause hardware
damage.
Step 5
Check the LEDs
For each LAN (PC) connection, the corresponding LAN LED should be ON (provided the PC is also ON.).
The ADSL LED should be also ON.
6
Login And System Status
3
Chapter 3
Login And System Status
This Chapter details the first time login procedure and the Status
screen
Login
ADE-4100 contains an HTTP server. This enables you to connect to it, and configure it, using your Web Browser. Your Browser must have JavaScript support.
The configuration program has been tested on the following browsers:
• Netscape V4.08 or later
• Internet Explorer V4 or later
Moreover, it is suggested to use an Ethernet LAN PC for the initial configuration of
ADE-4100.
Preparation
Before attempting to configure ADE-4100, please ensure that:
• Your PC can establish a physical connection to ADE-4100. The PC and ADE-
4100 must be directly connected (using the LAN port on ADE-4100) or on the
same LAN segment.
• ADE-4100 must be installed and powered ON.
• If ADE-4100's default IP Address (10.0.0.2) is already used by another device,
the other device must be turned OFF until ADE-4100 is allocated a new IP Address during configuration.
Connecting to ADE-4100
To establish a connection from your PC to ADE-4100:
1. After installing ADE-4100 in your LAN, start your PC. If your PC is already
running, restart it.
2. Start your WEB browser.
3. In the Address box, enter "HTTP://" and the IP Address of ADE-4100, as in this
example, which uses ADE-4100's default IP Address:
http://10.0.0.2
4. If connection is established, a pop-up password request page will show up. The
default login User Name of ADE-4100 administrator is “admin”, and Password
is “epicrouter”. The default login User Name for non-administrator is “user”,
and Password is “password”.
7
ADE-4100 User Manual
If you can't connect
Figure 3-1: Logon Window
If ADW does not respond, check the following:
• Machine is properly installed, LAN connection is OK, and it is powered
ON. You can test the connection by using the "Ping" command:
• Open the MS-DOS window or command prompt window.
• Enter the command:
ping 10.0.0.2
If no response is received, either the connection is not working, or
your PC's IP address is not compatible with ADE-4100's IP Address.
(See next item.)
• If your PC is using a fixed IP Address, its IP Address must be within the
range 10.0.0.3 to 10.255.255.254 to be compatible with ADE-4100's default IP Address of 10.0.0.2. Also, the Network Mask must be set to
255.0.0.0. See Chapter 5 - PC Configuration for details on checking
your PC's TCP/IP settings.
• Ensure that your PC and ADE-4100 are on the same network segment.
(If you don't have a router, this must be the case.)
8
Login And System Status
Status
Home
Once you login in ADE-4100, its Home page will appear. It shows the firmware
versions and WAN and LAN interface status.
Figure 3-2: Home page
ADSL
The ADSL Status page shows the ADSL physical layer status.
Figure 3-3: ADSL status
9
ADE-4100 User Manual
LAN
The LAN page shows the information and status of LAN port, DHCP client table,
and linking status of Ethernet interface.
Figure 3-4: LAN status
PPP
The PPP page shows the status of PPP for each PPP interface.
Figure 3-5: PPP status
10
4
Chapter 4
System Configuration
This Chapter details the configurations for ADE-4100
Overview
This chapter describes the setup procedure for:
• WAN Access
• LAN configuration
PCs on your local LAN may also require configuration. For details, see Chapter 5 PC Configuration.
WAN configuration
Select the WAN link under Configuration column to set up WAN connection. It is
required to know the type of Internet connection service used by your ISP.
Note: You only need to fill in the fields that your ISP provided, and leave the others
as default.
Figure 4-1: WAN Configuration
Per VC Setting
Under Per VC Setting, it provides the configurations for IP address, subnet mask,
gateway, and VPI/VCI, where VPI and VCI must be filled.
11
ADE-4100 User Manual
Figure 4-2: Per VC Settings
To switch between the PVCs, please choose the options of virtual circuit and click
on the Submit button to switch over.
Figure 4-3: Switch between PVCs
Internet connection services
Types of Internet connection services supported by ADE-4100 are explained below.
Bridge Mode
Step 1
At the WAN Configuration page, insert the VCI/VPI provided by ISP.
Enable “Bridge”, and choose suitable packet encapsulation.
Figure 4-4: Bridge status
12
Loading...