Planet Audio RX2.400, RX2.300, RX2.200, RX2.150, RX2.100 Users Manual

...
CONTENTS
RX MOSFET Amplifier User’s Manual - page 1
U S E R ’ S M A N U A L
2 Introduction
2 What is included?
3 Features
3 About 2 Ohm operation
4 General precautions
4 Installation precautions
4 Mounting the amplifier
5 Connecting the amplifier
6 Low level input wiring
8 High level input wiring
10 2CH Power and Speaker wiring
2CH Mode
11 2CH Power and Speaker wiring
Bridged Mode
12 2CH Power and Speaker wiring
TriMode
13 4CH Power and Speaker wiring
4CH Mode
14 4CH Power and Speaker wiring
Bridged Mode
15 4CH Power and Speaker wiring
TriMode
16 5CH Power and Speaker wiring
5CH Mode
17 5CH Power and Speaker wiring
Bridged Mode
18 5CH Power and Speaker wiring
TriMode
19 Troubleshooting
20 Specifications
Congratulations on your purchase of a Planet Audio RX Amplifier.
It has been designed, engineered and manufactured to bring you the highest level of performance and quality, and will afford you years of listening pleasure.
Thank you for making Planet Audio your choice for car audio entertainment!
page
RX2.400 RX2.300 RX2.200 RX2.150 RX2.100
Two Channel MOSFET Car Audio Amplifiers
RX4.400 RX4.300 RX4.200
Four Channel MOSFET Car Audio Amplifiers
RX5.600
Five Channel MOSFET Car Audio Amplifier
®
RX MOSFET Amplifier User’s Manual - page 2
Introduction
With the Planet Audio RX MOSFET amplifier series, we are introducing seven new amplifiers, all designed in the USA. This new series includes five 2-channel amplifiers, three 4-channel amplifiers and a versatile 5-channel amplifier.
All RX models feature variable low pass and high pass crossovers. Also featured are variable input gain controls with a input voltage sensitivity selectors.
For further flexibility in the use of a subwoofer, 0-+18dB Bass Boost control has been included on all amplifiers. Accurate control of time­alignment of the sound over the audibile spectrum is possible using the variable phase shift control.You can control the subwoofer level with the optional MOBB-12 remote level control module.
Planet Audio understands that amplifiers are placed in many different kinds of installations, so we incorporated a very flexible system of controls in these amplifiers in order to help you integrate the amp into your system regardless of the nature of your input source.
What is included?
When first unpacking your new amplifier, please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the amplifier.
• RX amplifier
•High input cable with connector
• Four (4) mounting screws
RX MOSFET Amplifier User’s Manual - page 3
Features About 2 Ohm operation
Your new RX amplifier features the following:
• Class A-B operation
• Bridgeable outputs
• Tri-Mode capable
• MOSFET PWM (Pulse Width Modulated) Power Supply
• 2 Ohm stable stereo operation with output power increase
• Thermal and speaker short protection
• Soft turn-on circuit
• Remote turn-on/turn-off circuit
• Variable input gain control
• HIgh voltage input sensitivity control
• Variable low pass crossover(s)
• Variable high pass crossover(s)
• Variable phase shift control
• Variable 0 to +18dB Bass Boost
• Chrome-plated RCA low level and high level inputs
• LED power and protection indicators
Your RX amplifier has been designed to operate efficiently at loads down to 2 Ohms. This means that you can install four 8 Ohm speakers per channel, when using parallel wiring.
Increasing the number of woofers per channel at low frequencies (below 100Hz) produces an acoustic coupling effect. This acoustic coupling effect increases your power output by about 3dB per speaker, or the equivalent of an additional 10W per speaker.
When operating at 2 Ohms, the amplifiers will increase their output power by approximately 50%. The
current draw will also increase by about the same amount, so be sure you have enough current to run the amplifiers into a 2 Ohm load.
If you lack adequate current, your music reproduction will be distorted.
RX MOSFET Amplifier User’s Manual - page 4
General precautions
SHOCK HAZARD! Do not open the case of this product. There are dangerous
voltages present within the unit. There are no user-serviceable parts within the unit.
Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals.
If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacturer's warranty.
Before installing and using your new Planet Audio amplifier, please become familiar with all the infor­mation contained in this manual.
Please keep this manual in a safe place for future reference.
• Do not open or attempt to repair this unit yourself. Dangerous high voltages are present which may result in electric shock. Refer any repairs to a qualified service technician.
• To avoid risk of electronic shock or damage to the amplifier, do not permit any of this equipment to become damp or wet from water or drinks. If this does occur, immediately unplug the power wires and send the amplifier to your local dealer or service center as soon as possible.
• If there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures, immediately unplug the power wire and send the amplifier to your local dealer or service center as soon as possible .
Installation precautions
Before you drill or cut any holes, investigate your car's layout very carefully. Take special care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring.
Never operate the amplifier when it is unmounted. Attach all audio system components securely to prevent damage, especially in an accident.
Mounting the amplifier
1. Find a suitable location in the vehicle in which to mount the amplifier.
2. Make sure there is sufficient air circulation around the intended mounting location.
3. Mark the location for the mounting hole screws by positioning the amplifier where you wish to install it. Use a scribe or mounting screw, inserted through each of the amp's mounting holes, to mark the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen.
4. Drill pilot holes in the mounting surface for the mounting screws. Place the amplifier in position, and attach the amplifier to the mounting surface securely using screws.
RX MOSFET Amplifier User’s Manual - page 5
Before doing any wiring, look through this manual and identify the diagrams to follow for power, input and speaker connections for your particular installation. Be sure you understand all the connections before you proceed.
1. Connect the power ground terminal to the closest point on the chassis of the car. Keep this ground wire to less than 39" (100 cm) in length. Use 8 gauge (or heavier) wire.
2. Connect the remote terminal to the remote output of the head unit using 16 gauge (or heavier) wire.
3. Connect an empty fuse holder within 18" (45 cm) of the car battery, and run 8 gauge (or heavier) cable from this fuse to the amplifier location.
4. Check that the fuse holder is empty. Then connect the fuse holder to the "BATT+" connection on the amplifier.
5. If multiple amplifiers are being used in your system, either:
• Run a separate pair of cables from the battery and a chassis ground point to each amplifier. Each (+) cable must have its own inline fuse.
-or-
• Run a #4 cable from the fuse holder at the battery to a distribution block at or near the amplifier's location. Then run separate cables from the amplifier to this distribution block and to independent chassis ground points.
6. Connect all line inputs and outputs (if used) using high-quality cables. Connect all speakers, following the diagrams in this manual. Be sure to observe proper polarity to avoid audio phase problems.
Connecting the amplifier
7. Insert fuse(s) into the battery fuse holder(s).
8. Recheck all connections before powering up the amplifier.
9. Set all level controls to minimum position, and set all crossover controls/switches to the desired frequency points.
10. Power up the head unit and the amplifier. Then set the volume control on the head unit to about 3/4 volume, and adjust the amplifier’s input level control(s) to just below the level of distortion.
11. Further fine tuning of the various controls may be necessary to obtain best results.
Do not mistake the input level control for a volume control! It is designed ONLY to match the output level of your audio source to the input level of your amplifier.
Do not adjust this input level to maximum unless your input level requires it.
Ignoring these instructions will result in an input overload to the amplifier, and excessive audio distortion. It can also cause the protection circuit to engage.
Don't misuse the level control!
RX MOSFET Amplifier User’s Manual - page 7
RX5.600
5-Channel Amplifier
To SUB Channel Audio Outputs of head unit or signal processor
INPUT MODE SWITCH in RCA position (sound delivered to amp CH5 is from CH5 panel inputs)
RX5.600
5-Channel Amplifier
To REAR Audio Outputs of head unit or signal processor
INPUT MODE SWITCH in 1+4 MIX position (sound delivered to amp CH5 is derived from channels 1-4)
1
CH
2
CH
HIGH LEVEL INPUTS
4
LEVEL
MIN MAX
INPUT CONTROLS
2-8V 100mV-2V
SENSITIVITY
INPUTS
3 2 1
HIGH PASS
FILTER
50 50 0
Hz
CHANNELS 1/2 CHANNELS 3/4
HIGH PASS
FILTER
50 500
Hz
3
CH
4
CH
2-8V 100mV-2V
SENSITIVITY LEVEL
MIN MAX
INPUT CONTROLS
REMOTE LEVEL CONTROL
5 Channel MOSFET Power Amplifier
5L
CH
5R
CH
CHANNEL 5
PHASE
0
180º
BASS BOOST
0
+18dB
INPUT CONTROLS
LEVEL
MIN
MAX
2-8V 100mV-2V
SENSITIVITY
POWER
PROTECTION
MIN MAX
INPUT MODE
1+4 MIX RCA
LOW PASS
FILTER
50 150
Hz
LEVEL FREQ
25 160
CHANNEL 5 GAIN
Hz
INPUTS INPUTS
Remote
Subwoofer Level Control
To FRONT Audio Outputs
of head unit or
signal processor
INPUT MODE
1+4 MIX RCA
System with input source with 4-channel outputs
1
CH
2
CH
HIGH LEVEL INPUTS
4
LEVEL
MIN MAX
INPUT CONTROLS
2-8V 100mV-2V
SENSITIVITY
INPUTS
3 2 1
HIGH PASS
FILTER
50 50 0
Hz
CHANNELS 1/2 CHANNELS 3/4
HIGH PASS
FILTER
50 500
Hz
3
CH
4
CH
2-8V 100mV-2V
SENSITIVITY LEVEL
MIN MAX
INPUT CONTROLS
REMOTE LEVEL CONTROL
5 Channel MOSFET Power Amplifier
5L
CH
5R
CH
CHANNEL 5
PHASE
0
180º
BASS BOOST
0
+18dB
INPUT CONTROLS
LEVEL
MIN
MAX
2-8V 100mV-2V
SENSITIVITY
POWER
PROTECTION
MIN MAX
INPUT MODE
1+4 MIX RCA
LOW PASS
FILTER
50 150
Hz
LEVEL FREQ
25 160
CHANNEL 5 GAIN
Hz
INPUTS INPUTS
Remote
Subwoofer Level Control
To FRONT Audio Outputs of head unit or
signal processor
INPUT MODE
1+4 MIX RCA
System with input source with 4-channel
plus sub channel outputs
To REAR Audio Outputs of head unit or signal processor
RX MOSFET Amplifier User’s Manual - page 9
5-Channel Amplifier
RX5.600
High Level Input Wiring
Please note: If you are using the high-level inputs, 5-channel operation is possible ONLY with the Input Mode switch in the “1+4 Mix” position.
To Speaker Terminals
of head unit
1
CH
2
CH
HIGH LEVEL INPUTS
4
LEVEL
MIN MAX
INPUT CONTROLS
2-8V 100mV-2V
SENSITIVITY
INPUTS
3 2 1
HIGH PASS
FILTER
50 50 0
Hz
CHANNELS 1/2 CHANNELS 3/4
HIGH PASS
FILTER
50 500
Hz
3
CH
4
CH
2-8V 10 0mV-2V
SENSITIVITY LEVEL
MIN MAX
INPUT CONTROLS
REMOTE LEVEL CONTROL
5 Channel MOSFET Power Amplifier
5L
CH
5R
CH
CHANNEL 5
PHASE
0
180º
BASS BOOST
0
+18dB
INPUT CONTROLS
LEVEL
MIN
MAX
2-8V 10 0mV-2V
SENSITIVITY
POWER
PROTECTION
MIN MAX
INPUT MODE
1+4 MIX RCA
LOW PASS
FILTER
50 15 0
Hz
LEVEL FREQ
25 160
CHANNEL 5 GAIN
Hz
INPUTS INPUTS
CH4+ CH3+ CH2+ CH1+
Remote
Subwoofer Level Control
RX MOSFET Amplifier User’s Manual - page 10
Power and Speaker Wiring
2 Channel
RX2.400, RX2.300, RX2.200,
RX2.150 and RX2.100
2-Channel Amplifiers
Two Channel Mode
SPEAKER
IMPEDANCE
2-8 OHMS
Connect the Positive (+) terminal of the subwoofer to the R (+) amplifier terminal.
Connect the Negative (-) terminal of the subwoofer to the L (-) amplifier terminal.
L R
BRIDGED MODE
+12V
REMOTE
GROUND
POWER CONNECTIONS
FUSES
SPEAKERS
RIGHT
Speaker
LEFT
Speaker
to REMOTE TURN-ON terminal of head unit
Chassis
ground
point
Battery
FUSE
RX MOSFET Amplifier User’s Manual - page 11
Power and Speaker Wiring
Bridged Mode
RX2.400, RX2.300, RX2.200,
RX2.150 and RX2.100
2-Channel Amplifiers
Connect the Positive (+) terminal of the subwoofer to the R (+) amplifier terminal.
Connect the Negative (-) terminal of the subwoofer to the L (-) amplifier terminal.
Bridged Mode
SPEAKER
IMPEDANCE
4-8 OHMS
L R
BRIDGED MODE
+12V
REMOTE
GROUND
POWER CONNECTIONS
FUSES
SPEAKERS
Subwoofer
to REMOTE TURN-ON terminal of head unit
Chassis
ground
point
Battery
FUSE
RX MOSFET Amplifier User’s Manual - page 12
Power and Speaker Wiring
Tri-Mode
RX2.400, RX2.300, RX2.200,
RX2.150 and RX2.100
2-Channel Amplifiers
Tri-Mode
Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO.
To set up the amplifier to run in this mode, put the crossover switches in the FULL position. Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below. Be sure to check the table at the bottom of this page to determine the correct capacitor and inductor values for the crossover frequency you wish to achieve.
RIGHT Speaker
LEFT Speaker
Component values for 6dB Passive Crossover
FREQUENCY INDUCTOR CAPACITOR
80 Hz 100 Hz 120 Hz 150 Hz
7.5mH
6.5mH
5.5mH 4mH
470uF 330uF 330uF 220uF
SPEAKER
IMPEDANCE
8 OHMS
L
R
BRIDGED MODE
+12V
REMOTE
GROUND
POWER CONNECTIONS
FUSES
SPEAKERS
Subwoofer
High pass filter crossover
Low pass
filter inductor
High pass filter crossover
MINIMUM SPEAKER
IMPEDANCE
4 OHMS
Battery FUSE
to REMOTE TURN-ON
terminal of head unit
Chassis
ground
point
RX MOSFET Amplifier User’s Manual - page 13
Power and Speaker Wiring
4 Channel Mode
RX4.400, RX4.300 and RX4.200
4-Channel Amplifiers
Four Channel Mode
SPEAKER
IMPEDANCE
2-8 OHMS
SPEAKER
IMPEDANCE
2-8 OHMS
CH4
Speaker
CH3
Speaker
CH2
Speaker
CH1
Speaker
SPEAKERS
FUSES
CH
1
CH
2
CH
3
CH
4
BRIDGED MODE BRIDGED MODE
+12V
REMOTE
GROUND
POWER CONNECTIONS
to REMOTE TURN-ON terminal of head unit
Chassis
ground
point
BatteryFUSE
Power and Speaker Wiring
Bridged Mode
RX4.400, RX4.300 and RX4.200
4-Channel Amplifiers
Bridged Mode
Connect the Negative (-) terminal of the RIGHT subwoofer to the CH4(-) amplifier terminal.
Connect the Postive (+) terminal of the RIGHT subwoofer to the CH3(+) amplifier terminal.
Connect the Negative (-) terminal of the LEFT subwoofer to the CH2(-) amplifier terminal.
Connect the Postive (+) terminal of the LEFT subwoofer to the CH1(+) amplifier terminal.
SPEAKER
IMPEDANCE
4-8 OHMS
SPEAKER
IMPEDANCE
4-8 OHMS
RIGHT
Subwoofer
LEFT
Subwoofer
SPEAKERS
FUSES
CH1CH
2
CH
3
CH
4
BRIDGED MODE BRIDGED MODE
+12V
REMOTE
GROUND
POWER CONNECTIONS
to REMOTE TURN-ON terminal of head unit
Chassis
ground
point
Battery
FUSE
SPEAKERS
FUSES
CH1CH
2
CH3CH
4
BRIDGED MODE BRIDGED MODE
+12V
REMOTE
GROUND
POWER CONNECTIONS
RX MOSFET Amplifier User’s Manual - page 15
Power and Speaker Wiring
Tri-Mode
RX4.400, RX4.300 and RX4.200
4-Channel Amplifiers
Tri-Mode
Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO.
To set up the amplifier to run in this mode, put the crossover switches in the FULL position. Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below. Be sure to check the table at the bottom of this page to determine the correct capacitor and inductor values for the crossover frequency you wish to achieve.
CH4 Speaker
CH3 Speaker
Component values for 6dB Passive Crossover
FREQUENCY INDUCTOR CAPACITOR
80 Hz 100 Hz 120 Hz 150 Hz
7.5mH
6.5mH
5.5mH 4mH
470uF 330uF 330uF 220uF
SPEAKER
IMPEDANCE
8 OHMS
CH1 Speaker
RIGHT Subwoofer
SPEAKER
IMPEDANCE
8 OHMS
MINIMUM SPEAKER
IMPEDANCE
4 OHMS
Low pass filter inductor
High pass filter crossover
High pass filter crossover
CH2 Speaker
LEFT Subwoofer
+
+
High pass filter crossover
Low pass
filter inductor
High pass filter crossover
MINIMUM SPEAKER
IMPEDANCE
4 OHMS
Battery FUSE
to REMOTE TURN-ON
terminal of head unit
Chassis ground
point
Power and Speaker Wiring
5 Channel Mode
RX5.600
5-Channel Amplifiers
Five Channel Mode
SPEAKER
IMPEDANCE
2-8 OHMS
SPEAKER
IMPEDANCE
2-8 OHMS
CH5
Speaker
SPEAKER
IMPEDANCE
2-8 OHMS
CH4
Speaker
CH3
Speaker
CH2
Speaker
CH1
Speaker
+12V
REMOTE
GROUND
POWER CONNECTIONS
CH1CH2CH3CH
4
CH
5
BRIDGED MODEBRIDGED MODE
SPEAKERS
FUSES
to REMOTE TURN-ON terminal of head unit
Chassis
ground
point
Battery
FUSE
RX MOSFET Amplifier User’s Manual - page 17
Power and Speaker Wiring
Bridged Mode
RX5.600
5-Channel Amplifiers
RIGHT Subwoofer
LEFT
Subwoofer
Bridged Mode
CH5
Speaker
Connect the Negative (-) terminal of the LEFT subwoofer to the CH2(-) amplifier terminal.
Connect the Postive (+) terminal of the LEFT subwoofer to the CH1(+) amplifier terminal.
SPEAKER
IMPEDANCE
4-8 OHMS
SPEAKER
IMPEDANCE
2-8 OHMS
SPEAKER
IMPEDANCE
4-8 OHMS
Connect the Negative (-) terminal of the RIGHT subwoofer to the CH4(-) amplifier terminal.
Connect the Postive (+) terminal of the RIGHT subwoofer to the CH3(+) amplifier terminal.
+12V
REMOTE
GROUND
POWER CONNECTIONS
CH1CH2CH3CH
4
CH
5
BRIDGED MODEBRIDGED MODE
SPEAKERS
FUSES
to REMOTE TURN-ON terminal of head unit
Chassis
ground
point
Battery
FUSE
RX MOSFET Amplifier User’s Manual - page 18
Power and Speaker Wiring
Tri-Mode
RX5.600
5-Channel Amplifiers
Tri-Mode
Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO.
To set up the amplifier to run in this mode, put the crossover switches in the FULL position. Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below. Be sure to check the table at the bottom of this page to determine the correct capacitor and inductor values for the crossover frequency you wish to achieve.
CH4 Speaker
CH3 Speaker
Component values for 6dB Passive Crossover
FREQUENCY INDUCTOR CAPACITOR
80 Hz 100 Hz 120 Hz 150 Hz
7.5mH
6.5mH
5.5mH 4mH
470uF 330uF 330uF 220uF
SPEAKER
IMPEDANCE
8 OHMS
CH5
Speaker
SPEAKER
IMPEDANCE
2-8 OHMS
CH1 Speaker
RIGHT Subwoofer
SPEAKER
IMPEDANCE
8 OHMS
MINIMUM SPEAKER
IMPEDANCE
4 OHMS
Low pass filter inductor
High pass filter crossover
High pass filter crossover
CH2 Speaker
LEFT Subwoofer
+
+
High pass filter crossover
Low pass
filter inductor
High pass filter crossover
MINIMUM SPEAKER
IMPEDANCE
4 OHMS
+12V
REMOTE
GROUND
POWER CONNECTIONS
CH1CH2CH3CH
4
CH
5
BRIDGED MODEBRIDGED MODE
SPEAKERS
FUSES
Battery
FUSE
to REMOTE TURN-ON
terminal of head unit
Chassis ground
point
Troubleshooting
RX MOSFET Amplifier User’s Manual - page 19
If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems.
Amplifier will not power up.
Check to make sure you have a good ground connection.
Check that the Remote Input (Turn-On) has at least 3VDC. Check that there is battery power on the (+) terminal.
Check that there is at least 12v. Check all fuses, replace if necessary.
Make sure that the Protection LED is not illuminated. If it is lit, shut off the amplifier briefly, and then repower it.
Protection LED comes on when amplifier is powered up.
Check for short circuits on speaker leads. Turn down the volume control on the head unit to prevent overdriving.
Remove speaker leads, and reset the amplifier. If the Protection LED still comes on, then the amplifier is faulty and needs servicing.
No output.
Check that all fuses are OK.
Check that amplifier is properly grounded. Check that the Remote Input (Turn-On) has at least 3VDC.
Check that the RCA audio cables are plugged into the proper inputs. Check all speaker wiring.
Low output.
Reset the Level Control.
Check the Crossover Control settings.
Audio present in only one channel.
Check the RCA interconnect cables.
Check all speaker wiring.
High hiss in the speakers.
Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then plug in the component driving the amplifier and unplug its inputs. If the hiss disappears at this point, go on until the faulty/noisy component is found. It is best to set the amplifier's input level control as low as possible. The best subjective signal-to-noise ratio is achieved in this manner. Try to set the head unit as high as possible (without distortion) and the amp input level as low as possible.
Squealing noise from speakers.
Check for improperly grounded RCA interconnects.
Distorted sound.
Check that the Input Level Control is set to match the signal level of the head unit. Always try to set the Input Level as low as possible.
Check that all crossover frequencies are properly set. Check for short circuits on the speaker leads.
Amplifier gets very hot.
Check that the minimum speaker impedance for the amp model is correct.
Check that there is good air circulation around the amp. In some applications, it may be necessary to add external cooling fan(s).
Engine noise (static type)
This is usually caused by poor quality RCA cables,which can pick up radiated noise. Use only the best quality cables, and route them away from power cables.
Engine noise (alternator whine)
Check that speaker leads are not shorted to the marine vessel chassis.
Check that the RCA grounds are not shorted to the marine vessel chassis.
Check that the head unit is properly grounded.
SYMPTOM POSSIBLE REMEDY
Specifications
All specifications subject to change without notice.
MAX POWER
into 2 Ohms
RMS POWER
into 4 Ohms
BRIDGED POWER
into 4 Ohms
Min. speaker impedance
THD
Frequency response
Signal-to-noise ratio
Channel separation
Damping factor
Crossover range
low pass
high pass
Bass boost
Fuse rating
Dimensions: (11" x 2
-5/8
" x ...)
MODEL RX4.200
Fou r Cha nne l MOS FE T A mplifi ers
150W x 4
75W X 4
300W x 2
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
30A x 2
17"
RX4.300
MAX POWER
into 2 Ohms
RMS POWER
into 4 Ohms
BRIDGED POWER
into 4 Ohms
Min. speaker impedance
THD
Frequency response
Signal-to-noise ratio
Channel separation
Damping factor
Crossover range
low pass
high pass
Bass boost
Fuse rating
Dimensions: (11" x 2-5/8" x ...)
MODEL
Two Cha nnel MOS FET A mpl if ier s
150W x 2
75W X 2
300W x 1
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
30A x 1
13-7/8"
RX2.150
200W x 2
100W X 2
400W x 1
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
20A x 2
16-1/4"
RX2.200
300W x 2
150W X 2
600W x 1
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
25A x 2
18-1/4"
RX2.300
400W x 2
200W X 2
800W x 1
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
40A x 2
22-7/8"
RX2.400
200W x 4
100W X 4
400W x 2
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
40A x 2
20-7/8"
RX4.400
Fiv e Cha nn el MO SFE T A mpli fie r
100W x 4 + 300W x 1
50W X 4 + 200W x 1
200W x 2 + 300W x 1
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
9Hz-50kHz
103dB
90dB
125+
35Hz-160Hz
200Hz (fixed)
Variable 0 - +18dB
30A x 2
20-7/8"
RX5.600
®
RX2.100
100W x 2
50W X 2
200W X 1
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
20Hz-20kHz
102dB
90dB
125+
50Hz-150Hz
50Hz-500Hz
Variable 0 - +18dB
20A x 1
11"
100W x 4
50W X 4
200W X 2
2 Ohm Stereo 4 Ohm Mono Bridged
0.01%
20Hz-20kHz
102dB
90dB
125+
50Hz-150Hz
50Hz-500Hz
Variable 0 - +18dB
20A x 2
14-3/4"
Loading...