Planet Audio PI9759B User Manual

PI9759B
PI9759B
i
is a trademark
d
o
registered in the U.S. and other countries
Planet Audio is not affiliated with Apple, Inc
®
P
of
Apple,
Digital
with dual (front and rear)
INSTRUCTIONS
INSTRUCTIONS
CONTENTS
Panel Introduction
Basic Function Remote Control Function Turn on/off Host
Access main interface
USB/SD Card function operation
Radio Function Operation
Disc Function Operation
Play/Eject Disc
DVD/VCD Disc Playback
CD Disc Playback
MP3/WMA Format Disc Playback
Touch Menu Function BT Function Operation Music function operation
External input operation
Other function operation
Rear view function Access setup interface
General setting
Time setting
Language setting
Video setting
Audio setting
Steering wheel setup
Touch calibration Wiring Diagram
Trouble shooting Specifications
Accessory
DVD Parental control function
02 03 05 07 07 07
08
09
09
09
09
09 09 11 12 12
12
12
13
13
13
13
13
14
14
14 16
16 17
18
18
ACCESSORY
Accessory
Wire
USB Cable
Remote Controller
Warranty card
DVD Parental control function
DVD Parental control function
DVD Parental control functionThe default set for DVD is #8 adult, which means all grades of DVD can be read without entering password.To change the default grade,you need to follow the below procedure: Press SETUP button on the remote, display will show the system set up menu
and the submenu,
0000, you will be able to choose the DVD grade as default.
select password and enter
Quantity
1PC
1PC
1PC
2PCS
Warning: To ensure safety while driving and to comply with laws, drivers should not watch video or operate the video device while driving.
01
18
INSTRUCTIONS INSTRUCTIONS
SPECITICATIONS
Power supply
Power range
Max operate current
Ground system
Amp Rating
FM tuner
European frequency range
USA frequency range
Signal / Noise ratio
Stereo separation
Search station volt
Distortion rate
AM tuner
European frequency range
USA frequency range
Limit noise sensitivity
DVD player
Signal / Noise ratio
Frequency response
This unit is with switchable frequency. You can switch from USA frequency to Europe frequency by following the below steps: Step1. In main menu, press setup icon to enter the setup interface.
Step2. Press the Radio icon,and insert password 123456, then press “OK”, the menu from which you can select the radio frequency will show.
Step3. Press “Radio region” and select the desired frequency by pressing the "up" and "down" arrow, then press it and setting is finished.
DC 12V
10.8-16.0V DC
15A
Negative ground
85 WattsX4 Channels
87.5-108MHz
87.5-107.9MHz
55dB
30dB
20-30dBuv
1.5%
522-1620KHz
530-1710KHz
32dB
70dB
20Hz-20KHz
PANEL INTRODUCTION
PI9759B
PI9759B
OPEN
MIC
PI9759B
OPEN
S
.
L
E
O
L
V
MIC
MODE
4 6 7 8 9
MODE
MUTE
5 10
S
.
L
E
O
L
V
MUTE
1 2
17
3
16 15 14
SD
2/RPT
1/
SD
2/RPT
1/
3/RDM
3/RDM
4/ 5/
4/ 5/
11
USB
USB
6/
12
6/
13
17
SD
RESET
18 19
02
INSTRUCTIONS
INSTRUCTIONS
BASIC FUNCTION
1. /OPEN Button
Press the button to open / close the screen. Press this button for short moment to turn on power, and long press it to turn off power.
2. SEEK Knob / ( / )/ (SEEK+ / SEEK-)/ (SEEK / SEEK)(Speed forward / backward / Select station / song)
In radio mode, press / rotate the knob to select station upward / backward. Long press / rotate the knob to automatically scan station. In playback mode, short press / rotate the knob to select song upward / backward, long press / rotate it to achieve speed forward / backward function.
3. RELEASE Button
Press this button to release the panel.
4. MODE Button
When the unit is power on, Repeat press this button can switch to different function mode as following picture. Note: When the device without connecting to USBSD or DVD no disc inside, the system will automatically skip these related working mode.
5. (VOL/SEL) Volume adjustment mode
Repeat pressing this button can select the VOLBASTREBALFAD adjustment mode, Then can rotate the button to adjust VOLBASTRE BAL FAD as you like.
6. MUTE Button
Press this button to shut off sound output, repress this button to resume sound output; Long press this button longer to turn on / off TFT LCD display.
7. Number Button 1 /
In radio mode, press this button to hear radio preset; In disc playback mode, press this button for Play/Pause.
8. Number Button 2 / RPT (Repeat Playback)
In radio mode, press this button to hear radio preset; In disc playback mode, press this button to repeat the current track indefinitely.
9. Number Button 3 / RDM (Random playback)
In radio mode, press this button to hear radio preset; In disc playback mode, press this button to play frocks on the disc in random order.
10. Number Button 4 /
In radio mode, press this button to hear radio preset; In disc playback mode, press this button for to stop playback.
BT
Music
03
WIRING DIAGRAM
This player is equipped with ISO standard connector, please follow below instruction:
Red - ACC ON (+12V)
Yellow – 12 V Constant
Black – Ground wire
Blue - Power Antenna / Remote Amp Turn On
Orange – Back-Up Camera Trigger (+)
A
FUSE
Connect to ignition key switch
GREY
GREY/BLACK
Right f ront
PURPLE
PURPLE/BLACK
Right r ear
Memory +
Connect to battery or +12V of Power Source that is always live
Ground -
Connect to Ground terminal
Connect to Power Antenna or remote control for Amplifier
Orange
CCD OFF
Pink
Connect to car reversing switch
Braking wire
WHITE
WHITE/BLACK
Left front
GREEN/BLACK
Left r ear
GREEN
Grey/Grey black - Right front speaker (+/-)
White/White black - Left front speaker (+/-)
Purple/Purple black - Right rear speaker (+/-)
Green/Green black - Left rear speaker (+/-)
Pink – Parking Brake (-)
Yell ow
Black
Red
Radio antenna
B
i-Pod
C
Light grey
Light grey
SWC wire
Rear USB
TROUBLE SHOOTING
PROBLEM
Cannot power on
After ignition switch off ,setting information all lose
Poor performance of radio station
Cannot load disk
Cannot play disc
Cannot switch language/subtitle
No image
Cannot watch image during driving
Check fuse
Some factors cause MPU wrong operation
Change battery or fuse
Weak signal
There is a disk inside
Disc is scratched
Put wrong side of disc into the unit
Lens is dirty
There is only one language/ subtitle in disc
Other factors cause MPU wrong operation
It’s not allowed to watch image during driving
CAUSE SOLUTION
Change fuse same as the old one
Press RES button on the panel by penpoint, then, power on
Reset information and save
Move the car to another place, then research
Remove disc before inserting another one
Change new disc
Insert in the disk with sign side up
Clean lens by lens clean disc
If disc is not with multi-language/subtitle, it cannot switch language/subtitle
Press [RES] button on the panel by penpoint, then, power on
Park the car in a safe place, put the car stall in “ P ” postion, pull up the hand brake, parking brake wire must be grounded
16
A
B
Dark grey
Dark grey
Light grey
Orange
Brown
Black
Black
Black
INSTRUCTIONS
Step 1: Press the mode button in the unit to switch to DVD mode.
INSTRUCTIONS
11. Number Button 5 /
In playback mode, press the button to adjust the angle of screen.
12. Number Button 6 /
In playback mode, press the button to adjust the angle of screen.
13. Dual (front and rear)AUX
To input external audio. Warning :You can only use either front or rear AUX at a time. Never connect both front and rear AUX at the same time.
14. Dual (front and rear)USB
Insert USB removable advice so as to read audio/video files. Warning :You can only use either front or rear USB at a time. Never connect both front and rear USB at the same time! This could cause malfunctions.
15. IR
To receive infrared signal from the remote control.
16.
When there is a disc in the unit, press the button to eject the disc.
17. MIC
BT microphone input socket.
18. SD
Insert SD card, the unit will play the files automatically.
15
19. RESET
Press this button and this unit will be restored to the initial state.
04
INSTRUCTIONS INSTRUCTIONS
REMOTE CONTROL FUNCTION
POWER ON/OFF
MUTE
SOURCE
EQ
SEEK+ / SEEK-
VOL+ / VOL-
SEL
LOUD
BAND / P / N
LOC / RDM
STOP
PLAY / PAUSE
ST / PROG
O-10+
1.POWER
Press once to switch on, press again to switch off.
2. MUTE Button
Press once to turn off audio output, press again to resume volume level.
AMS / RPT
TITLE
AUDIO
GO TO
SUB TITLE
PBC
UP / DOWN / L / R ENTER
SLOW
ANGLE
SETUP
OSD
ZOOM
MENU
28
DSP
3. SOURCE Button
Press this button to change mode.
4. EQ Button
Press this button to choose POPROCK CLASSICEQ off.
5. SEEK+ ( )/ SEEK-( ) Button
In normal playback MP3USBSD songs, Press this button to previous song or next song.
6. VOL+ ( ) / VOL- ( )
Press this button to increase or decrease volume level.
7. SEL Button
Press this button to choose sound feature.
8. LOUD Button
Press this button to startup LOUD function.
9. BAND-P/N Button
In radio mode, press this button to choose band. In VCDDVD mode, press this button to choose PALAUTO or NTSC system.
10. LOC/RDM Button
In radio mode, press this button to switch between local and direction. In VCDCD mode,press this key to randomly play.
11. STOP Button
Press this button to stop playing.
12. PLAY/PAUSE Button
Press this button to switch between play and pause. In stop mode, press this button to play.
13. ST/PROG Button
In radio mode, press this button to choose stereo or mono station. In audio mode, it can help STOP button to programmed play.
Audio setting
Click icon on setup interface to access audio setting interface, as shown in diagram: You can turn on or turn off the existing functions on audio setting interface.
PIC 1
right(PIC 1)
Steering wheel setting
I. Click icon on setup interface so as to access steering wheel setting interface. II.Connect anode and cathode of direction control wire of the car with anode and cathode of direction control wire of this device, and press the buttons on steering wheel one by one and record the corresponding sequence and functions.
III. Click the button of steering wheel needs to be allotted so as to select the corresponding setting function, such as volume +.
IIII. Buttons on steering wheel shall display the corresponding functions, such as volume + .
To modify function settings, repeat procedures 3~4. To reset functions, click [Reset] icon, all the settings set before shall be cleared, repeat
procedures 3~4 for resetting.
Touch calibration
If touch calibration error occurs, you can adjust the touch coordinate by “Touch calibration”. Click icon on setup interface, input password [888888] to confirm to access touch
calibration interface, as shown in below diagram:
Touching methods
Use touch pen to click the center of “+” icon, and move along with center of “+” icon so as to calibrate the screen. It shall automatically save data and exit after screen calibration. Please accurately click all positions on screen, or the accuracy of touch calibration shall be affected.
05
14
INSTRUCTIONS INSTRUCTIONS
Access setup interface
Click [Setting] icon on main interface to access setup interface.
General setting
Click icon on setup interface to access general setting interface, as shown in below PIC 1 diagram: In general setting interface, you can select to turn on or turn off the existing functions. You can set wallpaper and opening picture you like and check version number of DVD/ MCU, click icon to browse up/down.
Wallpaper selection
Click icon on wallpaper bar , direction icon shall pop up, click it to select wallpaper.
Time setting
Click icon on setup interface to access time setting interface,12h/24h interchangeable, as shown in below PIC 2diagram:
Click icon on time bar time setting interface shall display, as shown in below PIC 3 diagram: Click icon beside hour and minute to separately set hour and minute.
PIC 2PIC 1
PIC 3
Language setting
During use, you can select your familiar language to display menu by language setup. Click icon on setup interface to access language setting interface, as shown in right (PIC 4) diagram:
Click the corresponding icon on the language bar desired to be set so as to switch the language type, when there are more than 3 languages, direction icon shall pop up, click it to select your familiar language.
Video setting
Click (PIC 5) diagram:
At video setting interface, you can adjust brightness, contrast, saturation and hue of the video.
icon on setup interface to access video setting interface, as shown in right
14. 0-10+ Button
Press this button to choose desired song sectionpreset stations. Decimal numbers, for example the 19th song, press 10+ and 9 button.
15. AMS / RPT Button
In radio mode, press this button to browse stored stations. In audio mode, press this button to play repeatedly.
16. TITLE Button
In DVD mode, press this button to play back to the top menu of disc.
17. AUDIO Button
In DVD mode, press this button to switch language of dialogue. In VCD mode, press this button to choose left trackright track and stereo.
18. GO TO Button
In DVD mode, press this button, you can define playing time.
19. SUB TITLE Button
In DVD mode, press this button to switch language of subtitle.
20. PBC Button
In VCD mode, press this button to display all song menus, work with number button to choose songs.
21. UPDOWNLEFT RIGHTENTER Button
When playing MP3USBSD returns to song menu, up
down selections can be
up / " " button or down / " " key to select up and down, select and press " " key to confirm. The selected tracks can be played. Press the left or right arrow keys to " " or " " key, can be on the next page function operation.
22. SLOW Button
In audio mode, press this button to slow backward and slow forward.
23. ANGLE Button
In DVD mode, press this button to change play angle.
24. SETUP Button
In audio mode, press this button to choose different set items.
25. OSD Display
Press this button to display the title chapter and the left time.
26. ZOOM Button
In DVD/VCD mode, press this button to ZOOM in.
27. MENU Button
Press button to back to the main menu.
28. DSP
Press this button to show the time.
BATTERY CHANGE
When control distance of remote control becomes shorter or no function, please change battery. Please confirm polarity before change.
One hand press stopper, then pull out battery.
Put battery into controller.
Insert battery holder into controller.
PIC 4
13
PIC 5
06
INSTRUCTIONS INSTRUCTIONS
Turn on/off Host
When the ignition switch is put in ACC or ON position,Press[ ] button on the front panel to turn on the unit.After the host starts, hold [ ]button for 3 seconds , the host will turn off.
Access main interface
In the other mode, click on the interface to return the icon will switch to the main interface.
Touch the function icons so as to access the corresponding function operations.
USB/SD Card function operation
When there is a USB device/SD card connected, the unit can conduct the playback of audio/video/ image files in the USB device/SD card.
Insert/Eject USB storage device
1. Connect a USB recorded with media information to the unit by a USB connecting cable.
2. When there is a need to eject the USB device, exit the USB device playback screen first, and then take out the device.
Insert/eject SD card
1. Insert a SD card recorded with media information into the SD card slot in the unit correctly until it is locked.
2. When pulling out the SD card, exit SD card playing state first, then press the SD card and it shall pop up after unlocking.
Enter/exit
Insert a USB storage device or SD card to automatically play data contained in it. If the unit has connected with a USB device or SD card, touch[ USB ]icon in the main interface to enter into the external storage playback interface; Touch[ SD ]icon to enter into the SD card playback interface. During playback, touch the top center area of the screen to pop up the touch menu, operate touch menu to perform various playback controls.
Play
After SD card/USB removable device being read out, the operation methods are similar to disk operation methods.
Music function operation
Connect to Music first, touch [ Music ] icon on main interface to access Music interface, as shown in below diagram.
Fast forward play/Fast backward play
Play/Pause
Stop
Volume adjustment knob
Previous Song/next Song
Back to the main interface
External input operation
Connect the video input plug with external video input jack, and connect the audio input plug with external audio input jack.
Touch [ AUX ] icon on main interface to access external input interface.
Audio You can adjust the
volume, bass, pitch for input audio.
You can adjust the speaker volume by adjusting the front and back,left and right column. Video You can adjust the brightness, contrast, saturation and hue for input video.
You can also choose the video standard mode.
Region 1
NO VIDEO SIGNAL
Region 2
Warning: In AUX mode, you can adjust the angle of screen by press region 1 & region 2. Press Region 1 to slide up, press Region 2 to slide down.
Other function operation
Rearview function
In any running state, the video signal can switch to reverse video state when reversing the car, and the system shall return to its initial running state after reversing the car.
Warning
Do not rely on CCD system completely, please make sure you use direct eyesight while driving.Back rearview system only assists in driving. As the distance range of rearview system is limited, completely relying on the rearview system during driving may cause accidents.
07
Reverse field simulation
12
Rearview backup image
INSTRUCTIONS INSTRUCTIONS
BT Function Operation
Enter/exit
Touch [ BT ] icon in the main interface to enter the BT interface. Touch icon to exit BT interface.
Pair/link
To use BT hand-free function, make connection first, i.e. match the host with the BT mobile phone.
Operation methods:
Set the host to be matching state, and open the BT of your mobile phone and use the mobile phone to search device, the mobile phone shall prompt to match password with the BT when it has searched the BT device. Input BT password (0000) to the mobile phone and confirm. The mobile phone shall prompt whether authorize to this device,please select [Yes]. Phone and BT shall automatically connect within 20 seconds. Under any working mode, the host shall convert to BT state if there is an incoming call. And the host shall restore to current mode after hanging up.
When the BT device matches with this device, the connection status shall display “ LINK OK ”, otherwise, it shall display “NO LINK ”.
Dialing
You can dial on mobile phone directly or input phone number through the number buttons on the screen, click to delete if there is input error.
After input the phone number, click to make a call, and click to hang up the phone. Click during a call so as to switch the voice between car speaker and mobile phone.
Call records
Click to access call records interface as below PIC 2: Received calls: Touch this button to check all the phone numbers of received calls.
Dialed numbers: Touch this button to check all the dialed phone numbers. Missed calls: Touch this button to check all the phone numbers of missed calls.
BT volume
Click to access BT volume interface as below PIC 3:
Radio Function Operation
Enter/exit
Touch [ RADIO ] icon in the main interface to enter into the radio interface. Touch icon to return to main interface, and then touch other function icons so as to exit
radio mode.
Band selection
Click [BND] icon so as to switch among AM1, AM2 bands.FM1,FM2, FM3,
Search/Save radio stations
Short press [Scan] icon to browse the stored radio stations. FM band can save 18 radio stations (Six stations for FM1/FM2/FM3), AM band can save
12 radio stations (Six stations for AM1/AM2).
Scan radio
Short press icon to manually fine-tune radio stations upward/downward. Long press icon to automatically search and save radio stations.
Sound setting
Click [EQ] icon can switch to different sound mode.
Mute on/off
Click [Mute] icon to turn on/off mute function
TFT on/off
Click icon to turn off TFT, and then click the screen area so as to turn on TFT. Click icon so as to slide screen angle.
RDS Function
RDS function provides series information (such as traffice information, name of station), and can automatically switch to the station with stronger signal and carries the same program.
AF: Touch the button to turn on/off AF mode
TA: Touch the button to turn on/off TA mode
PTY: Touch the button the screen displays program types, users can search station according to program type
If the unit does not have RDS function, it has no AF/TA/PTY function. The corresponding icon appears grey.
PIC 2PIC 1
Previous song
11
Play/pause
Next song
PIC 3
08
INSTRUCTIONS INSTRUCTIONS
Disc Function Operation
Play/eject disc
Play disc
Insert the disc into the disc slot with the printing surface up, system will detect the disc and automatically take it in to read and play.
Eject disc
(1) Click button on the panel to eject the disc. (2) If a disc has not been took away 15 seconds after it is ejected, system will automatically take in the disc but not play.
Do not insert two discs or more.
DVD/VCD disc playback
During playback of disc, touch the middle lower area of the screen to pop up the touch menu, operate the touch menu to perform various playback controls.(PIC 1)
CD Disc Playback
After a CD is inserted, system shall access disc reading state immediately. When there is a disc in the device, click [Disc] at the main interface so as to access disc reading state. After the disc being read out, system shall automatically play in sequence.
MP3/JPEG/MPEG4 disk playing
When the disc contains readable files, such as MP3/JPEG/MPEG4 files, it shall be automatically read out and played after slipping into DVD player.
During playing, touch the screen area and the touch menu shall pop up. Operate the touch menu for various playing.
Touch Menu Function Description
Play/pause
Touch the button to pause, retouch it to continue to play.
Stop
Touch the button to enter into prestop status.
Fast forward/backward
Consecutively touch this button to select the speed of fast-forward/fast-backward.
The previous/next song
Touch the button to select the previous/next song.
Volume adjustment button Touch this button and volume adjustment modulation shall pop up, touch button to adjust the volume.
TT 1/5 CH 1/1
x
00
TT 1/5 CH 1/1
x
00
Access next menu
Touch it to access the next menu interface.
Time setting
Touch this button to access time setting interface.
Stereo on/off
Touch it so as to turn on/off stereo.
Return to root menu
Touch this icon, it shall return to root menu of disk in DVD state and access PBC menu playing in VCD state. All chapters in the disk shall be displayed on the interface, touch the chapter icon directly for playing.
Access title menu
Press this button to return to title menu of the disk. Directly click menu bar at title menu interface for playing.
Repeat play
In playing state, touch this button to start repeat play function: Chapter repeat Title repeat Repeat All Off.
During VCD playing, this function only works when PBC is off.
Language selection
Touch this button to select language.
Digit keyboard
Touch this button and digit keyboard shall appear, click number buttons directly to select tracks for playing.
Randomly play
Touch this button to instantly play each song. Press again to back to the normal play.
Zoom in/Zoom out image
Touch this button to zoom in /zoom out the image.
00:01:44 00:09:43
VOL
PIC 1
09
00:01:44 00:09:43
VOL
10
Loading...