PI9746B
PI9746B
i
is a trademark
d
o
registered in the U.S. and other countries
Planet Audio is not affiliated with Apple, Inc
®
P
of
Apple,
Inc.
Digital
INSTRUCTIONS
CONTENTS
Panel Introduction
Basic Functions
Remote Control Function
Turn the Unit On/Off
Enter into the Main Interface
Play SD card/USB memory device
Radio Function Operation
Disc Function Operation
Play/Eject Disc
DVD/VCD Disc Playback
CD Disc Playback
MP3/WMA Format Disc Playback
Touch Menu Function
Bluetooth Function Operation
IPOD function operation
External input operation
Other Function Operations
Rear view function
General setting
Time setting
Language Setup
Video Setup
Audio setting
Steering Wheel Setup
Touch calibration
Wiring
Diagram
Trouble shooting
Specifications
Accessory
DVD Parental control function
02
03
05
07
07
07
08
09
09
09
09
09
09
11
12
12
12
12
13
13
13
13
14
14
14
16
16
17
18
18
ACCESSORY
Accessory
Wire
USB Cable
Remote Controller
Warranty card
DVD Parental control function
DVD Parental control function
DVD Parental control function：The default set
for DVD is #8 adult, which means all grades of
DVD can be read without entering password.To
change the default grade,you need to follow the
below procedure: Press SETUP button on the
remote, display will show the system set up menu
and the submenu,
0000, you will be able to choose the DVD
grade as default.
select password and enter
INSTRUCTIONS
Quantity
1PC
1PC
1PC
2PCS
Warning: To ensure safety while driving and to comply with laws, drivers should not
watch video or operate the video device while driving.
01
18
INSTRUCTIONS INSTRUCTIONS
SPECITICATIONS
Power supply
Power range
Max operate current
Ground system
Amp Rating
FM tuner
European frequency range
USA frequency range
Signal / Noise ratio
Stereo separation
Search station volt
Distortion rate
AM tuner
European frequency range
USA frequency range
Limit noise sensitivity
DVD player
Signal / Noise ratio
Frequency response
This unit is with switchable frequency.
You can switch from USA frequency to Europe frequency by following the
below steps:
Step1. In main menu, press setup icon to enter the setup interface.
Step2. Press the Radio icon, and insert password 123456, then press “OK”,
the menu from which you can select the radio frequency will show.
Step3. Press “Radio region” and select the desired frequency by pressing the "up"
and "down" arrow, then press it and setting is finished.
DC 12V
10.8-16.0V DC
10A
Negative ground
85 WattsX4 Channels
87.5-108MHz
87.5-107.9MHz
55dB
30dB
20-30dBuv
1.5%
522-1620KHz
530-1710KHz
32dB
70dB
20Hz-20KHz
PANEL ARRANGEMENT
MUTE
12
1.SRC Button
2.MUTE/TFT on/off Button
3.VOLUME- Button
4.VOLUME+ Button
5.DN Button
6.UP Button
7.DBAS Button
8.OPEN Button
9.RESET Button
10.Remote Control Receiver
11.
12.
1
11
USB Slot
AUX IN
2
PI9746B
DBAS
17
02
INSTRUCTIONS
INSTRUCTIONS
BASIC FUNCTION
1. SRC Button
Press this button shortly to power on, press this button longer to power off.
In normal situation, press SOURCE button can return to the main menu.
2. MUTE/TFT on/off Button
Press this button to shut off sound output, repress this button to resume sound output;
Press this button longer to turn on/off TFT LCD display.
3. VOLUME - Button
Press this button shortly decrease volume level one step by one step. Press this
button longer decrease volume level continuously.
4. VOLUME + Button
Press this button shortly Increase volume level one step by one step. Press this
button longer Increase volume level continuously.
5. DN Button
Press this button to make the LCD monitor down.
6. UP Button
Press this button to make the LCD monitor up
7.DBAS Button
Press this button to bass on/off.
8. OPEN Button
Press this button can eject the disc.
9. RESET Button
Press this button and this unit will be restored to the initial state.
10.Remote Control Receiver
It is able of receiving infrared signals launched by the remote control matching the unit.
11. Dual (front and rear)USB
Warning: You can only use either front or rear USB at a time. Never connect both
front and rear USB at the same time! This could cause malfunctions.
12. AUX IN
External connected audio input.
WIRING DIAGRAM
This player is equipped with ISO standard connector, please follow below instruction:
● Red - ACC ON (+12V)
● Yellow – 12 V Constant
● Black – Ground wire
● Blue - Power Antenna / Remote Amp Turn On
● Orange – Back-Up Camera Trigger (+)
Rear USB/SWC
Radio antenna
Bluetooth MIC
IPOD
AUX input
Rear right speaker
Rear left speaker
Front right speaker
Front left speaker
Subwoofer output
● Grey/Grey black - Right front speaker (+/-)
● White/White black - Left front speaker (+/-)
● Purple/Purple black - Right rear speaker (+/-)
● Green/Green black - Left rear speaker (+/-)
● Pink – Parking Brake (-)
Video output 2
+
Green
Rear
Green/black Purple/black
-
Left track speaker
+
White
Front
White/black Grey/black
-
Pink (Safety cable)
CCD
Video input
Wire socket
Wire plug
Video output 1
TROUBLE SHOOTING
PROBLEM
Cannot power on
After ignition switch
off ,setting
information all lose
Poor performance
of radio station
Connot load disk
Cannot play disc
Cannot switch
language/subtitle
No image
Cannot watch
image during
driving
Check fuse
Some factors cause MPU
wrong operation
Change battery or fuse
Weak signal
There is a disk inside
Disc is scratched
Put wrong side of disc into
the unit
Lens is dirty
There is only one language/
subtitle in disc
Other factors cause MPU
wrong operation
It’s not allowed to watch image
during driving
CAUSE SOLUTION
Change fuse same as the old one
Press RES button on the panel by
penpoint, then, power on
Reset information and save
Move the car to another place, then research
Remove disc before inserting another one
Change new disc
Insert in the disk with sign side up
Clean lens by lens clean disc
If disc is not with multi-language/subtitle,
it cannot switch language/subtitle
Press [RES] button on the panel by
penpoint, then, power on
Park the car in a safe place, put the car stall
in “ P ” postion, pull up the hand brake,
parking brake wire must be grounded
Grey
Rear
Front
+
+
-
Purple
Right track speaker
Blue (Radio antenna control)
Blue/White (Remote control for Amplifier)
Orange (CCD)
Red (Key switch/ACC)
Yellow (Battery +)
Black (GND)
03
16
INSTRUCTIONS
INSTRUCTIONS
BASE
13.Disc Slot
14.Slot indicator light
15.SD Slot
13
14
15
15
04
INSTRUCTIONS INSTRUCTIONS
REMOTE CONTROL FUNCTION
3. SOURCE Button
Press this button to choose audio sources.
4. EQ Button
Press this button to choose POP、ROCK、
CLASSIC、EQ off.
5. SEEK+ ( )/ SEEK-( ) Button
In normal playback MP3、USB、SD songs,
Press this button to previous song or next
song.
6. VOL+ ( ) / VOL- ( )
Press this button to increase or decrease
volume level.
7. SEL Button
Press this button to choose sound feature.
8. LOUD Button
Press this button to startup LOUD function.
POWER ON/OFF
MUTE
SOURCE
EQ
SEEK+ / SEEK-
VOL+ / VOL-
SEL
LOUD
BAND / P / N
LOC / ROM
STOP
PLAY / PAUSE
ST / PROG
O-10+
AMS / RPT
TITLE
AUDIO
SET PLAYING TIME
SUBTITLE
PBC / MENU
UP / DOWN / L / R ENTER
SLOW
ANGLE
SETUP
OSD
ZOOM
MENU
9. BAND-P/N Button
In radio mode, press this button to choose
band.
In VCD、DVD mode, press this button to
choose AUTO、PAL or NTSC system.
10. LOC/RDM Button
In radio mode, press this button to switch
between local and direction.
In VCD、CD mode,press this key to randomly
play.
11. STOP Button
Press this button to stop playing.
Audio setting
Click icon on setup interface to access audio setting interface, as shown in
diagram:
You can turn on or turn off the existing functions on audio setting interface.
PIC 1
right(PIC 1)
Steering wheel setting
I. Click icon on setup interface so as to access steering wheel setting interface.
II.Connect anode and cathode of direction control wire of the car with anode and cathode of
direction control wire of this device, and press the buttons on steering wheel one by one
and record the corresponding sequence and functions, then click [Allocation].
III. Click the button of steering wheel needs to be allotted so as to select the corresponding
setting function, such as volume +.
IIII. Buttons on steering wheel shall display the corresponding functions, such as volume + .
To modify function settings, repeat procedures 3~4. Click [Enter] to save the settings.
To reset functions, click [Reset] icon, all the settings set before shall be cleared, repeat
procedures 3~4 for resetting.
Touch calibration
If touch calibration error occurs, you can adjust the touch coordinate by “Touch calibration”.
Click icon on setup interface, input password [888888] to confirm to access touch
calibration interface, as shown in below diagram:
Touching methods
Use touch pen to click the center of “+” icon, and move along with center of “+” icon so as
to calibrate the screen. It shall automatically save data and exit after screen calibration.
Please accurately click all positions on screen, or the accuracy of touch calibration shall be
affected.
1.POWER
Press once to switch on, press again to
switch off.
2. MUTE Button
Press once to turn off audio output,
press again to resume volume level.
12. PLAY/PAUSE Button
Press this button to switch between play and
pause.
In stop mode, press this button to play.
13. ST/PROG Button
In radio mode, press this button to choose
stereo or mono station.
In audio mode, it can help STOP button to
programmed play.
05
14
INSTRUCTIONS INSTRUCTIONS
Access setup interface
Click [Setting] icon on main interface to access setup interface.
General setting
Click icon on setup interface to access general setting interface, as shown in below
PIC 1 diagram:
In general setting interface, you can select to turn on or turn off the existing functions.
You can set wallpaper and opening picture you like and check version number of DV/DC,
click icon to browse up/down.
Wallpaper selection
Click icon on wallpaper bar , direction icon shall pop up, click it to
select wallpaper.
Time setting
Click
PIC 2diagram:
Click icon on time bar time setting interface shall display, as shown in
below PIC 3 diagram:
Click icon beside hour and minute to separately set hour and minute.
icon on setup interface to access time setting interface, as shown in below
PIC 2PIC 1
PIC 3
Language Setup
During use, you can select your familiar language to display menu by language setup.
Click icon on setup interface to access language setting interface, as shown in right
(PIC 4) diagram:
Click the corresponding icon on the language bar desired to be set so as to switch
the language type, when there are more than 3 languages, direction icon shall pop up,
click it to select your familiar language.
Video setting
Click
(PIC 5) diagram:
At video setting interface, you can adjust brightness, contrast, saturation and hue of the video.
icon on setup interface to access video setting interface, as shown in right
PIC 4
13
PIC 5
14. 0-10+ Button
Press this button to choose desired song
section、preset stations.
Decimal numbers, for example the 19th
song, press 1.9 button;
Centesimal numbers, for example, the
120th song, press 1.2.0 button.
15. AMS / RPT Button
In radio mode, press this button to browse
stored stations.
In audio mode, press this button to play
repeatedly.
16. TITLE Button
In DVD mode, press this button to play
back to the top menu of disc.
17. AUDIO Button
In DVD mode, press this button to switch
language of dialogue.
In VCD mode, press this button to choose
left track、right track and stereo.
18. SET playing time
In DVD mode, press this button, you can
define playing time.
19. SUBTITLE Button
In DVD mode, press this button to switch
language of subtitle.
20. PBC Button
In VCD mode, press this button to display
all song menus, work with number button
to choose songs.
21. UP、DOWN、LEFT、 RIGHT、ENTER
Button
、
When playing MP3、USB、SD returns to
song menu, up
、down selections can be
up / " " button or down / " " key to
select up and down, select and press " "
key to confirm.
The selected tracks can be played. Press
the left or right arrow keys to " " or " "
key, can be on the next page function
operation.
06
22. SLOW Button
In audio mode, press this button to slow
backward and slow forward.
23. ANGLE Button
In DVD mode, press this button to change
play angle.
24. SETUP Button
In audio mode, press this button to choose
different set items.
25. OSD Display
Press this button to display the title chapter
and the left time.
26. ZOOM Button
In DVD/VCD mode, press this button to
ZOOM in.
27. MENU Button
Press button to back to the main menu.
BATTERY CHANGE
When control distance of remote control
becomes shorter or no function, please
change battery. Please confirm polarity
before change.
One hand press stopper, then pull out battery.
Put battery into controller.
Insert battery holder into controller.
INSTRUCTIONS INSTRUCTIONS
Turn on/off Host
When the ignition switch is put in ACC or ON position,Press[ ] button on the front panel
to turn on the unit.After the host starts, hold [ ]button for 3 seconds , the host will turn off.
Access main interface
In the other mode, click on the interface to return the icon will switch to the main interface.
Touch the function icons so as to access the
corresponding function operations.
USB/SD Card function operation
When there is a USB device/SD card connected,
the unit can conduct the playback of audio/video/
image files in the USB device/SD card.
Insert/Eject USB storage device
1. Connect a USB recorded with media information to the unit by a USB connecting cable.
2. When there is a need to eject the USB device, exit the USB device playback screen
first, and then take out the device.
Insert/eject SD card
1. Insert a SD card recorded with media information into the SD card slot in the unit
correctly until it is locked.
2. When pulling out the SD card, exit SD card playing state first, then press the SD card
and it shall pop up after unlocking.
Enter/exit
Insert a USB storage device or SD card to automatically play data contained in it. If the
unit has connected with a USB device or SD card, touch[ USB ]icon in the main interface
to enter into the external storage playback interface; Touch[ SD ]icon to enter into the SD
card playback interface. During playback, touch the top center area of the screen to pop
up the touch menu, operate touch menu to perform various playback controls.
Play
After SD card/USB removable device being read out, the operation methods are similar
to disk operation methods.
iPod function operation
Connect to iPod first, touch [iPod] icon on main interface to access iPod interface, as
shown in below diagram.
Fast forward play/Fast backward play
Play/Pause
Stop
Volume adjustment knob
Previous Song/next Song
Back to the main interface
External input operation
Connect the video input plug with external video input jack, and connect the audio input
plug with external audio input jack.
Touch [Input] icon on main interface to access external input interface.
Audio You can adjust the
volume, bass, pitch for input audio.
You can adjust the speaker volume by adjusting the front and back,left and right column.
Video You can adjust the brightness, contrast, saturation and hue for input video.
You can also choose the video standard mode.
NO VIDEO SIGNAL
Other functions
Rearview function
In any running state, the video signal can switch to reverse video state when reversing the
car, and the system shall return to its initial running state after reversing the car.
Warning
Do not rely on CCD system completely, please make sure you use direct eyesight while
driving.Back rearview system only assists in driving. As the distance range of rearview
system is limited, completely relying on the rearview system during driving may cause
accidents.
07
Reverse field simulation
12
Rearview backup image
INSTRUCTIONS INSTRUCTIONS
Bluetooth Function Operation
Enter/exit
Touch [ Bluetooth ] icon in the main interface to enter the bluetooth interface.
Touch icon to exit bluetooth interface.
Pair/link
To use Bluetooth hand-free function, make connection first, i.e. match the host with the
Bluetooth mobile phone.
Operation methods:
Set the host to be matching state, and open the Bluetooth of your mobile phone and use
the mobile phone to search device, the mobile phone shall prompt to match password with
the Bluetooth when it has searched the Bluetooth device.
Input Bluetooth password (0000) to the mobile phone and confirm. The mobile phone
shall prompt whether authorize to this device,please select [Yes]. Phone and Bluetooth
shall automatically connect within 20 seconds. Under any working mode, the host shall
convert to Bluetooth state if there is an incoming call. And the host shall restore to current
mode after hanging up.
When the Bluetooth device matches with this device, the connection status shall display
“Connected”, otherwise, it shall display
“No connection”.
Dialing
You can dial on mobile phone directly or input phone number through the number buttons
on the screen, click to delete if there is input error.
After input the phone number, click to make a call, and click to hang up the phone.
Click during a call so as to switch the voice between car speaker and mobile phone.
Call records
Click to access call records interface as below PIC 2:
Received calls: Touch this button to check all the phone numbers of received calls.
Dialed numbers: Touch this button to check all the dialed phone numbers.
Missed calls: Touch this button to check all the phone numbers of missed calls.
Bluetooth volume
Click to access Bluetooth volume interface as below PIC 3:
Radio Function Operation
Enter/exit
Touch [ RADIO ] icon in the main interface to enter into the radio interface.
Touch icon to return to main interface, and then touch other function icons so as to exit
radio mode.
Band selection
Click [BND] icon so as to switch among AM1, AM2, Fm1,FM2, FM3 bands.
Search/Save radio stations
Short press [Scan] icon to browse the stored radio stations.
FM band can save 18 radio stations (Six stations for FM1/FM2/FM3), AM band can save
12 radio stations (Six stations for AM1/AM2).
Scan radio
Short press icon to manually fine-tune radio stations upward/downward.
Long press icon to automatically search and save radio stations.
Sound setting
Click [EQ] icon can switch to different sound mode.
Mute on/off
Click [Mute] icon to turn on/off mute function
TFT on/off
Click icon to turn off TFT, and then click the screen area so as to turn on TFT.
Click icon so as to slide screen angle.
PIC 2PIC 1
previous song
11
PLAY/PAUSE
next song
PIC 3
08
INSTRUCTIONS INSTRUCTIONS
Disc Function Operation
Play/eject disc
Play disc
Insert the disc into the disc slot with the printing surface up, system will detect the disc
and automatically take it in to read and play.
Eject disc
(1) Click button on the panel to eject the disc.
OPEN
(2) If a disc has not been took away 15 seconds after it is ejected, system will
automatically take in the disc but not play.
Do not insert two discs or more.
DVD/VCD disc playback
During playback of disc, touch the middle lower area of the screen to pop up the touch
menu, operate the touch menu to perform various playback controls.(PIC 1)
CD Disc Playback
After a CD is inserted, system shall access disc reading state immediately.
When there is a disc in the device, click [Disc] at the main interface so as to access disc
reading state.
After the disc being read out, system shall automatically play in sequence.
MP3/JPEG/MPEG4 disk playing
When the disc contains readable files, such as MP3/JPEG/MPEG4 files, it shall be
automatically read out and played after slipping into DVD player.
During playing, touch the screen area and the touch menu shall pop up. Operate the
touch menu for various playing.
Touch Menu Function Description
Play/pause
Touch the button to pause, retouch it to continue to play.
Stop
Touch the button to enter into prestop status.
Fast forward/backward
Consecutively touch this button to select the speed of fast-forward/fast-backward.
The previous/next song
Touch the button to select the previous/next song.
Volume adjustment button
Touch this button and volume adjustment modulation shall pop up, touch button to
adjust the volume.
TT 1/5 CH 1/1
x
00
TT 1/5 CH 1/1
x
00
Access next menu
Touch it to access the next menu interface.
Time setting
Touch this button to access time setting interface.
Stereo on/off
Touch it so as to turn on/off stereo.
Return to root menu
Touch this icon, it shall return to root menu of disk in DVD state and access PBC
menu playing in VCD state. All chapters in the disk shall be displayed on the interface,
touch the chapter icon directly for playing.
Access title menu
Press this button to return to title menu of the disk. Directly click menu bar at title
menu interface for playing.
Repeat play
In playing state, touch this button to start repeat play function: Chapter repeat
Title repeat Off.
During VCD playing, this function only works when PBC is off.
Language selection
Touch this button to select language.
Digit keyboard
Touch this button and digit keyboard shall appear, click number buttons directly to
select tracks for playing.
Randomly play
Touch this button to instantly play each song. Press again to back to the normal play.
Zoom in/Zoom out image
Touch this button to zoom in /zoom out the image.
00:01:44 00:09:43
VOL
PIC 1
09
00:01:44 00:09:43
VOL
10
Loading...