Planet Z64 User Manual

USER MANUAL

Model Z64

Congratulations on purchasing this excellent multifunction home/office alarm security system. This system has a
clearly written English User Manual providing step by step instruction for set up.

STEP 1

Preparation of Sensors for Installation

 Motion Detectors.
A. turn ON/OFF

switch to OFF position

B. open motion detector and install battery
C. maintain ON/OFF

switch in OFF position

 Window/Door Sensor.
A. separate sensor from magnetic bar
B. opens the sensor and installs battery
C. keeps sensor and bar separate

 Smoking Detector.
Install battery

 Gas Detector and Glass Break Detector.
Plug power cord into wall outlet.

 Wireless Portable Keypad.
Open back cover. Install battery.

 Attach Wired Siren

Insert plug of your alarm siren into siren jack on keypad/dialer

 Attaching telephone to keypad/controller.

A. Insert your telephone line into the “LINE” jack of the keypad/dialer.
B. Insert the line from your telephone into the “TEL

” jack of the keypad/dialer.

Notice: A phone line inserted into the wrong dialer phone jack may prevent the accessibility of the keypad/dialer from a remote location by
telephone.





Powering up

This keypad/controller has a security enhancing design which locates the on/off switch on the top of the

keypad/dialer unit, push down on the blue on/off button (with a pencil point)

A. Plug the power cord into

power receptacle and then into your wall outlet.

B. Turn keypad/controller powers switch “ON

”.

Rec switch

Study
Switch

On/off
switch











 Activating Wireless Outdoor Siren.

A. Turn keypad/controller power switch on. Depress the keypad “

PANIC” button.

B. Plug power cord of wireless outdoor siren into power receptacle and then into your wall outlet. Repeat this action until

you hear “short sound”, and then you will hear “long sound” that indicating it has been activated. Turn keypad power switch

off.

 Activating Wireless Luxury out/in door Siren w/strobe.

B. Turn keypad/co ntroller power switch on. Depress the keypad “

PANIC” button.

B. Plug power cord of wireless luxury out/in doo r siren w/strob e into power receptacle an d then into you r wall outlet. Repeat

this action until you hear “short sound”, and then you will hear “long sound” that indicating it has been activated. Turn

keypad power switch off.



 Activating Wireless Siren /w Strobe.

Plug siren. Depress and hold black button on side of cover which will produce pulsating light in red LED case. Hold button
until light is steady on. Turn keypad power switch on. Depress and hold black siren button again. Pulsating light in red LED
reappears. Depress the keypad PANIC button. Pulsating siren light will steady and go off (release black button).four red lights
will come on. Registration complete. Turn keypad power switch off.

STEP 2

Each component of the alarm system has to be activated to become functional; all activation takes place when
the system is in Programming status,

When you have completed programming the system’s functions, push

the button “Exit

” on the keypad; after 30 second system will automatically exit “Programming status”

1. To place system into Programming status.

Enter the factory password numbers 1

, 2, 3, 4 and push the button #. (You can substitute your own password for

factory password see section “2”). You are now in programming status

and in position to program any of the

changes listed below.

1 => 2 => 3 => 4 => #

2. Changing the Password.

5 => 1 => * => Enter your new password (4 digits) => #

3. Activating Your Keychain Remote /Panic button.

With your system in programming status enter the number below. In word of the trigger,
A. Push any of the four buttons on your keychain remote. You will hear double beeping sounds indicating that your

keychain remote is now activated.

B. Push buttons on your panic button. You will hear double beeping sounds indicating that your panic button is now

activated.

Study => 6 => 4 => # => trigger

The study switch on the
top of the keypad/dialer
unit;

A. Push any button on keychain.
B. Push button on panic button.

Activating the detectors

Our system supports 32 defense zones. This system is unique in letting you know exactly which sensor is setting off
the alarm. Each individual sensor (Motion detector, window/door sensor, smoking/gas detector, glass break detector)
has to be individually activated while unit is in “programming status”. Each sensor is programmed to have its own
numerical identity. Same types of sensors/detectors can share the same assigned numerical number. To perform this,
you first assign a two digit numbers to each sensor. Window/door sensors may be assigned any number between 09
and 64(notice: must 2 digits); motion detectors, smoke & gas detectors any number between 01 and 09(notice: must
2 digits). These are zone numbers. You may use the same assigned zone for up to 99 sensors. When a sensor is

triggered the assigned zone number will light up on the LED screen of the keypad. It may be helpful for you to keep a list of the
areas corresponding to the assigned zones.

4. Activating Door/Window Sensors. Each sensor needs to be numbered

For each door/window sensor, choose a number from 09 to 63 (notice: must 2 digits), with your system in
programming status, enter the number below into your keypad/controller. In the place of {09 to 63}, enter the
number you have chosen for the sensor. In place of trigger, you will need to physically trigger the door/window
sensor to activate it by bring the magnetic bar and the sensor together and then separating them. Activation will be
confirmed by a double beeping sound. Each door/window sensor has to be individually activated using this
procedure.

Study => {09 to 63} => # => trigger

Trigger
Door/window sensor

(Separate sensor from
magnetic bar)

Enter the number for
selected this sensor from
09-63, (must 2

digits)