Planet WDAP-850AC Installation Manual
Dual Band 802.11ac 1200Mbps Wave 2
Outdoor Wireless AP
►
WDAP-850AC
1. Package Contents
Thank you for choosing PLANET Outdoor Wireless AP. Before installing,
please verify the contents inside the package box. The device mentioned
herein is the brief name of the "Outdoor Wireless AP".
IMPORTANT SAFETY PRECAUTIONS:
1) LIVES MAY BE AT RISK! Please be aware of the
electrical wires around. Carefully read the section
"OUTDOOR INSTALLATION WARNING" in the manual
before installation.
2) Users MUST complete grounding wired with the
device; otherwise, a sudden lightning could cause fatal
damage to the device. EMD (Lightning) DAMAGE IS
NOT COVERED UNDER WARRANTY.
3) Users MUST power off the device first before connecting
the antenna to it; otherwise, damage might be caused to
the device itself.
4) The Antenna and Surge Arrestor are required for each
antenna connector, and must be purchased separately.
2. Physical Introduction
WDAP-850AC
L-type Bracket x 1
Quick Guide
RJ45 Waterproof Kit x 1
Screw Set x 1U-bolt Kit x 2
If there is any item missing or damaged, please contact the
seller immediately.
Note
– 1 – – 2 –
3. Hardware Installation
Step 1: (1) Install the backplane to the back of the AP.
(2) Attach the L-type bracket to the backplane and fasten it.
(3) Place the AP to the pole and fasten it with the U-bolt kit
※ The AP can be mounted on the pole with a diameter of up
to 2.5”.
L-type Bracket
Hardware Description
5GHz N-type (F)
Antenna Connectors
2.4GHz N-type (F)
Antenna Connectors
WAN/PoE Port
Ground Terminal
Step 2: (1) Attach the surge arrestors to each antenna connector.
(2) Attach the antenna equipped with N-type (M) connector to
each surge arrestor. Otherwise, connect the antenna
through the N-male (male pin) to N-male (male pin)
cable.
(3) Plug the RJ45 Ethernet cable into the PoE port of the AP
through the waterproof kit, and plug the other side of the
RJ45 cable into the PoE port of the PoE switch to finish the
installation.
※ Please remember to finish grounding by consulting the
local electrical experts.
U-bolt Kit
Antenna
Surge Arrestor
To PoE Switch/Injector
– 3 – – 4 –
4. Web Login
A computer with wired Ethernet connection is required for the first-time
configuration of the device.
1. Click the “Start” button located in the lower-left corner of your
computer.
2. Click “Control Panel”.
3. Double-click the “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double-click “Local Area Connection”.
6. Select “Internet Protocol Version 4 (TCP/IPv4)” and click
“Properties”.
7. Select “Use the following IP address” and then click the “OK”
button twice to save the configuration. For example, you may choose
from 192.168.1.1 to 192.168.1.254 excluding the default IP address
of the device (192.168.1.253).
Default IP Address: 192.168.1.253
Default Password: admin
Default 2.4GHz SSID: PLANET_2.4G
Default 5GHz SSID: PLANET_5G
Step 1: The Web management allows you to access and manage the
device easily. Launch the Web browser and enter the default IP
address http://192.168.1.253
Step 2: When the login window appears, please enter the password.
The default password is “admin”. Then click the Login button
to continue.
– 5 – – 6 –
Step 3: For security reasons, it is strongly recommended to go to
Managed to configure the Encryption Method and Passphrase
of your wireless network.
For security reasons, it is recommended to change the password at the
first login and memorize it.
Further Information:
The above steps introduce the simple installations and configurations of
the device. For further configurations, please refer to the user manual,
which can be downloaded from the website.
WDAP-850AC:
https://www.planet.com.tw/en/support/downloads?&method=keywor
d&keyword=WDAP-850AC&view=3#list
If you have further questions, please contact the local dealer or
distributor where you purchased this product.
PLANET Technology Corp.
10F., No. 96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
Warning:
This device is compliant with Class A of CISPR 32.
In a residential environment this device may cause radio interference.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy savings, please remove the DC plug or slide
the hardware-based Power Switch to the OFF position to disconnect the device from the power circuit. Without removing the DC
plug from or switching off the device, the device will still consume power from the power source. In view of Saving the Energy
and reducing the unnecessary power consumption, it is strongly suggested to power off or to remove the DC plug from the
device if this device is not intended to be active.
– 7 – – 8 –
2011-E10760-000
Loading...