Planet WDAP-702AC, WBS-502AC Quick Installation Manual
Quick Installation Guide
WDAP-702AC
1200Mbps Dual Band 802.11ac
Outdoor Wireless AP
1. Package Contents
IMPORTANT SAFETY PRECAUTIONS:
1. LIVES MAY BE AT RISK! Please be aware of the
electrical wires around. Carefully read the section
"OUTDOOR INSTALLATION WARNING" in the manual
before installation.
2. Users MUST complete grounding wired with the device;
otherwise, a sudden lightning could cause fatal damage
to the device. EMD (Lightning) DAMAGE IS NOT
COVERED UNDER WARRANTY.
3. Users MUST use the “PoE Injector and Power Cord”
shipped in the box with the device. Use of other options
will cause damage to the device.
Thank you for choosing PLANET Outdoor Wireless AP. Before installing,
please verify the contents inside the package box. The device mentioned
herein is the brief name of the "Outdoor Wireless AP/CPE".
WDAP-702AC Quick Guide
Mounting Ring x 1
Screw Set x 1
PoE Injector & Power Cord
2.4GHz Antenna x 2
5GHz Antenna x 2
If there is any item missing or damaged, please contact the
seller immediately.
Note
– 1 – – 2 –
3. Hardware Installation
Step 1:
(1) Remove the bottom cover.
(2) Connect one end of the Ethernet cable into the LAN (Passive PoE)
port of the device and the other end to the PoE port on the PoE
Injector.
(3) Connect the power cord with the PoE Injector and plug the other
end into an electrical outlet.
(4) Connect the second Ethernet cable into the LAN port of the PoE
Injector and the other end to the Ethernet port on the computer.
2. Physical Introduction
Hardware Description
2.4GHz
5GHz
LEDsGrounding Terminal
Reset Button
LAN1 (Passive PoE)
RP-SMA Connector
LAN2
Power
LAN 2
LAN 1
Step 2: Place the bottom cover back into the device and attach the
antennas onto the antenna connectors of the device to finish
the installation.
Step 3: Pole Mounting
(1) Thread the open end of the mounting ring through the tab on the
pole mounting bracket on the back of the device.
(2) Lock and tighten the mounting ring to secure the mounting bracket
to the pole to finish the installation.
1
1
1
2
3
3
2
2
4
To PC
– 3 – – 4 –
Step 4: Wall Mounting
(1) Mark the locations on the surface for the two mounting holes. Use
the appropriate drill bit to drill two holes with a diameter of 8.1mm
and depth of 26mm.
(2) Hammer the anchors into the holes until they are aligned to the
wall.
(3) Screw the screws into the anchors.
(4) Place the device against the wall with the mounting screw heads to
finish the installation.
1
2
3
4
4. Web Login
A computer with wired Ethernet connection is required for the first-time
configuration of the device.
1. Click the “Start” button located in the lower-left corner of your
computer.
2. Click “Control Panel”.
3. Double-click the “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double-click “Local Area Connection”.
6. Select “Internet Protocol Version 4 (TCP/IPv4)” and click
“Properties”.
7. Select “Use the following IP address” and then click the “OK”
button twice to save the configuration. For example, you may choose
from 192.168.1.1 to 192.168.1.254 excluding the default IP address
of the device (192.168.1.253).
– 5 – – 6 –
Default IP Address: 192.168.1.253
Default User Name: admin
Default Password: admin
Default 2.4GHz SSID: PLANET_1-2.4GHz
Default 5GHz SSID: PLANET_1-5GHz
Step 1: The Web management allows you to access and manage the
device easily. Launch the Web browser and enter the default IP
address “http://192.168.1.253”.
Step 2: When the login window appears, please enter the User Name
and the Password. The default User Name and Password are
both “admin”. Then click the Login button to continue.
Step 3: After you enter into the Web User Interface, click Wireless on
the left hand side of the screen to configure the wireless
connection. Once the basic configuration of the device is done,
go to the Changes page to save and apply the changes.
Further Information:
The above steps introduce the simple installations and configurations of
the device. For further configurations, please refer to the user manual,
which can be downloaded from the website.
For security reasons, it is recommended to change the password at the
first login and memorize it.
– 7 – – 8 –
WDAP-702AC:
http://www.planet.com.tw/en/support/download.php?ty
pe1=4&model=48986&type=3
If you have further questions, please contact the local dealer or
distributor where you purchased this product.
2011-E10690-000
Loading...