2.4 / 5 GHz 1000mW WLAN Booster
WBT-1000/1000A
Quick Installation Guide
Table of Contents
WBT-1000 ....................................................................................................... 4
Package Contents ....................................................................................... 4
Specications ............................................................................................. 4
Features .................................................................................................... 5
Hardware Installation .................................................................................. 5
WBT-1000A ..................................................................................................... 7
Package Contents ....................................................................................... 7
Specications ............................................................................................. 7
Features .................................................................................................... 8
Hardware Installation .................................................................................. 8
Preparations ...................................................................................................10
Troubleshooting ..............................................................................................11
Copyright
Copyright © 2009 by PLANET Technology Corp. All rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specically disclaims any warranties,
merchantability or tness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, PLANET reserves the
right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
FCC Regulation
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Revision
Quick Installation Guide for PLANET 2.4 / 5 GHz WLAN Booster
Model: WBT-1000/1000A
Rev: 2.0 (June, 2009)
Part No. EMQ-WBT1000v2
4
WBT-1000
Package Contents
The following items should be included:
Outdoor Wireless Amplier Unit x 1
l
DC Injector Unit x 1
l
l
Mounting Kit x 1
l
30 cm male RP-SMA to male N type cable x 1
l
Quick Installation Guide x 1
l
Power Adapter x 1
If any of the above items are damaged or missing, please contact your dealer
immediately.
Specications
Operating Range
Operating Mode
Connector Type
RF Input power
Transmit Gain
Output Power
Receiver Gain
Noise Figure
Frequency Response
DC Power Input
Operating Temp.
Operating Humidity
Material
Lightning Protection
DC Surge Protection
LED
Outdoor Unit (cm)
DC Injector (cm)
Weight
2400~2500 MHz
Bi-directional, half-duplex, auto-switching via carrier
sensing
N-type, female (50 ohm)
0~15dbm
Warning: Input power more than 15 dBm may
breakdown the power amplier.
18dB
1W (30 dBm)
15 dB
3.5dB
± 1 dB over operating range
9V DC, 2.0 A
-20 to +70˚C
Up to 95% relative humidity
Cast Aluminum
Direct DC ground at antenna connector
At DC input from transmission cable
DC Power (Yellow), Transmit Active (Green)
10.8 cm (L) x 6.8 cm (W) x 3.0 cm (H)
10.2cm (L) x 3.6cm (W) x 2.6cm (H)
345g (Booster) / 96g (DC Injector)
Features
High Gain, High Value and High Performance/ Auto Gain Signal Booster
l
l
Amplify and AP’s radio signal to 30dBm
l
Make broadband wireless application in possible coverage
l
Increase AP’s receiving sensitivity up to -100dB
l
Increasing radio communication range by providing transmit gain as well as lownoise receive gain.
l
Aluminum case construction/weather-proof/ Lightning protection
l
Strength radio signal to increase the effective range and coverage area for Wi-Fi
communication.
l
Simply attach the DC Injector with 2.4GHz radio signal input plus the DC power
feed to the outdoor unit and N type antenna.
l
The outdoor booster increase range by providing transmit gain as well as low
noise receive gain.
The benet for signal booster can save lots of wiring costs and easy to build
l
wireless infrastructure for home or business use
Hardware Installation
5
6
Step 1: Connect AP Radio to DC injector with 30 cm male RP-SAM to male N type
Note
cable.
Step 2: Connect DC Injector and Outdoor Booster Unit with optimum length
extend cable (<50 meters).
Step 3: Connect the Outdoor Booster Unit and the Antenna with RF cable (<50
cm).
Step 4: Plug in the power adapter to the DC Injector Unit.
Step 5: Adjust antenna for best signal reception.
1. Make sure the TX power of the AP Radio follow the required RF
power input.
2. Please connect antenna before power on, also do not disassemble antenna while operating, otherwise, it will cause the
device damage.
WBT-1000A
Package Contents
The following items should be included:
Outdoor Wireless Amplier Unit x 1
l
l
DC Injector Unit x 1
l
Mounting Kit x 1
l
30 cm male RP-SMA to male N type cable x 1
l
Quick Installation Guide x 1
l
Power Adapter x 1
If any of the above items are damaged or missing, please contact your dealer
immediately.
Specications
Operating Range
Operating Mode
Connector Type
Input power
Output Power
Receiver Gain
Noise Figure
Frequency Response
DC Power input
Operating Temp.
Operating Humidity
Material
Lightning Protection
DC Surge Protection
LED
Outdoor Unit (cm)
DC Injector (cm)
Weight
5150 ~ 5850 MHz
Bi-directional, half-duplex, auto-switching via carrier
sensing
N-type, female (50 ohm)
0~15dbm
Warning: Input power more than 15 dBm may
breakdown the power amplier.
1W (30 dBm)
15 dB typical
5 dB typical
± 1 dB over operating range
9V DC, 2.0 A
-20 to +70°C
Up to 95% relative humidity
Cast Aluminum
Direct DC ground at antenna connector
At DC input from transmission cable
Transmit Active (Green)
11.5cm (L) x 6.5cm (W) x 4.8cm (H)
10.2cm (L) x 3.6cm (W) x 2.6cm (H)
345g (Booster) / 96g (DC Injector)
7
8
Features
Note
High Gain, High Value and High Performance/Auto Gain Signal Booster
l
l
Amplify and AP’s radio signal to 30dBm or more
l
Make broadband wireless application in possible coverage
l
Increase AP’s receiving sensitivity up to -100dB
l
Increasing radio communication range by providing transmit gain as well as lownoise receive gain.
l
Aluminum case construction/weather-proof/Lightning protection
l
Strength radio signal to increase the effective range and coverage area for Wi-Fi
communication.
l
Simply attach the DC Injector with 5GHz radio signal input plus the DC power
feed to the outdoor unit and N type antenna.
l
The outdoor booster increase range by providing transmit gain as well as low
noise receive gain.
The benet for signal booster can save lots of wiring costs and easy to build
l
wireless infrastructure for home or business use
Hardware Installation
For WBT-1000A Booster Unit, Please face the LED Indicator down
when installation.
Step 1: Connect AP Radio to DC injector with 30 cm male RP-SAM to male N type
Note
cable.
Step 2: Connect DC Injector and Outdoor Booster Unit with optimum length
extend cable (<50 meters).
Step 3: Connect the Outdoor Booster Unit and the Antenna with RF cable (<50
cm).
Step 4: Plug in the power adapter to the DC Injector Unit.
Step 5: Adjust antenna for best signal reception.
1. Make sure the TX power of the AP Radio follow the required RF
power input.
2. Please connect antenna before power on, also do not disassemble antenna while operating, otherwise, it will cause the
device damage.
9
10
Preparations
Note
Note
Note
In order to obtain the best performance of booster and system, user must
calculate the transmission power to meet the booster technical requirement and
FCC regulations. Please follow the calculation below:
1. Convert power of the radio device from milliwatt to dBm.
10 * Log (milliwatt)
2. Estimate the attenuation of cable (please refer to manufacturer’s specications)
It is suggested that the cable loss between booster and DC injector
should not exceed 10 dBm.
General Cable Attenuation List
LMR400 LMR600 LMR900
dB loss per meter
Suggested max. cable length (m)
3. Calculate the actual power of booster in the pole as follow:
Radio Device Power (dBm) – Cable Loss (dBm) – Misc. Loss = Input Signal Level
(dBm)
0.221 0.144 0.098
45.24 69.44 102.04
Misc. Loss means loss of connector, adapter and DC injector and
estimates to be around 2 dB.
4. When the input signal level exceeds the Receiver Input Power of booster, the
booster can’t identify the input signal. Under this circumstance, user should
lower the input signal level to t the requirement such as using an attenuation
pad or a higher loss cable and vice versa.
Troubleshooting
If there is no signal output, please check the following item:
1. Check whether the LED indicator on the DC injector is on. If not, it means there
is problem with the power component.
(1) Check if the power cord is correctly connected with the power adapter and
the power outlet.
(2) Check if there is electricity on power outlet.
2. Check if the radio device is working properly.
3. Check if the connection between booster and DC injector is correct, or whether
the connector is loose or not.
4. Verify if the transmit power which calculated before is correct.
5. If none of the above measures could solve the issue, please contact the supplier
for further support.
11
This page is intentionally left blank
Loading...