PLANET VF-102-KIT User Manual

Download

VF-102-KIT

Optical Fiber Transmission System

User’s Manual

Trademarks

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. The information in this manual is subject to change without notice. All other trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or

tness for a particular purpose.

PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.

Information in this User’s Manual is subject to change without notice and does not represent a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s Manual, at any time without notice.

If you nd information in this manual that is incorrect,

misleading, or incomplete, we would appreciate your comments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

WEEE Warning

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end

users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

Video over Optical Fiber Media Converter User’s Manual

For Models: VF-102-T / VF-102-R

Rev 1.0 (AUGUST 2009)

Part No.: 2350-AA3700-000

Table Of Contents

1. INTRODUCTION ................................................................6

1.1 CHECK LIST ...............................................................6

1.2 INTRODUCTION TO VIDEO OVER FIBER CONVERTER .... 6

1.3 KEY FEATURES ...........................................................7

1.4 PRODUCT SPECIFICATION ...........................................8

2. HARDWARE DESCRIPTION ...............................................

2.1 Front Panel .............................................................. 10

2.1.1 Ports connection .............................................. 10

2.1.2 LED Indicators ................................................ 10

2.2 Rear Panel ............................................................... 11

3 INSTALL THE CONVERTER ...............................................

3.1 Limitation ................................................................ 12

3.2 Stand-alone Installation ............................................ 12

3.3 Chassis Installation and Rack Mounting ...................... 13

3.4 Optional - DIN-Rail mounting ....................................

4 POWER INFORMATION ....................................................

1. INTRODUCTION

1.1 CHECK LIST

Check the contents of your package for following parts:

VF-102-T – Video over Fiber Media Converter / Transmitter x 1

VF-102-R – Video over Fiber Media Converter / Receiver x 1

5V / 2A Power Adapter x 2

User’s Manual x 1

If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.

1.2 INTRODUCTION TO VIDEO OVER FIBER

CONVERTER

This Video over Fiber Converter kit consists of a Video Transmitter, VF-102-T, and a Video Receiver, VF-102-R. It

is a digital ber-optic transmission system which provides

customer a cost-effective solution for transmission of 1 channel uncompressed digital video and 1 reverse RS-422/485 async-

data over one single ber cable. It is adjustment free device

while providing high quality and real-time video. The plug-andplay design makes the installation more convenient and easier. The system can be widely used in Intelligent Transportation

Systems (ITS), Trafc Surveillance, security monitoring,

automation control, intelligent residential districts and so on.

Typical Applications

Intelligent Transportation Systems (ITS)

Toll Collection

Trafc Surveillance

Air Trafc Management (ATM)

Rail Signaling

Perimeter Alarms and Area Monitors

Telemedicine and Teleconference

Industrial Surveillance

Intelligent Building

1.3 KEY FEATURES

Video + Data over ber transmission

8 bit Video Signal digital sampling

PAL, NTSC, SECAM compatible

20km max. distance

Data Type: RS-422 / RS-485

Standalone or work with PLANET MC-700/1500/1500R media

converter chassis

Compact in size, wall-mount design, easy installation

1.4 PRODUCT SPECIFICATION

Model VF-102-T VF-102-R

Video Characteristic

Video Channel 1 channel Bi-direction

Signal Mode NTSC / PAL

Video Connector BNC

Video Input/Output Impedance

Video Input/Output Voltage

Video Bandwidth 6.5MHz

Video Digital Bit Width 8/10 bit

Differential Gain (DG) <1.3% (Typical Value)

Differential Phase (DP) <1.3° (Typical Value)

SNR Weighted 63dB (Typical Value)

Data Interface

Data Channel 1 channel

Physical Protocol RS-422 / RS-485

Operation Mode Simplex

Data Connector

Data Rate DC-115.2Kbps

Data Distance RS-485: 0-1200m

Bit Error Rate (BER) < 10

Optical Interface

Optical Connector FC

Fiber Type Single-mode, single ber

Distance (Max.) 20km for single mode

75ohm / unbalanced interface

1.0 Vpp / Typical peak-peak value

3 Pin terminal block with screw clamps

-9

Optical Wavelength

Launch Power (dBm)

Receive Sensitivity (dBm)

Max Loss Budget 18dB

Max. Input Power (dBm)

Cable 9/125μm single-mode cable

Hardware Specication

LED Indicators

Dimension (W x D x H)

Weight 215g

Power Requirement 5V DC / 2A

Power Consumption 4.8Watts (maximum)

Mechanical Metal

Compatible Converter Chassis

Standards Conformance

Regulation Compliance FCC Part 15 Class A, CE

Environment

Operating

Storage

TX: 1310nm RX: 1550nm

Max. : -7 Min. -14

-32dBm

• One Power

• One for Video

- Green, Link

• One for Fiber Optic

- Green, Link

94 x 70 x 26 mm

MC-700 / MC-1500 / MC-1500R

Temperature: -10 ~ 60 Degree C Relative Humidity: 0 ~ 95% (non-condensing)

Temperature: -40 ~ 85 Degree C Relative Humidity: 5 ~ 95% (non-condensing)

TX: 1550nm RX: 1310nm

2. HARDWARE DESCRIPTION

PWR

GND

LNK

VF-102

Videoover Fiber Converter

OPTIC

VIDEO

RS422/485

2.1 Front Panel

The units’ front panel provides a simple interface monitoring the

converter. There are FC ber optical interface and VIDEO socket

in the front panel. For the VF-102-T / VF-102-R which reverse data connector, the RS485/422 DATA port may be connected to the user’s interface end.

2.1.1 Ports connection

Video Connection:

Async-data Connection:

Fiber Connection:

Connecting the video signal to or from the

product through a 75Ω coax cable with BNC

plug.

● Connect the output data port (eg. TX+ and

TX-) of other control device to the RX+ and RX- of the RX.

● Connect the input data port (eg. RX+ and

RX-) of other under controlled device to the TX+ and TX- of the TX.

● GND in both TX and RX should be

connected directly to user’s equipment.

Connect the ber-optic cable pigtail (with

FC/PC or ST/PC optical connector) to the product’s FIBER port.

2.1.2 LED Indicators

The rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system. There are “POWER”, “VIDEO”, “LINK” 3 LEDs in the front panel of TX/RX. Each LED lightens means:

LED Color Function

Power Notice

POWER Green Power supply OK

VIDEO Green Lighted when video in

LNK Green Lighted when laser in

2.2 Rear Panel

The rear panel of the converter indicates one DC jack, which accepts input power with 5V DC 2A.

1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.

2. In some area, installing a surge suppression device may also help to protect your converter from being damaged by unregulated surge or current to the converter or the power adapter.

3 INSTALL THE CONVERTER

This section describes how to install your VF-102 Media Converter and make connections to the converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of PLANET VF-

102 Media Converter do not need software conguration. To

install your VF-102 on a desktop or shelf, simply complete the following steps.

3.1 Limitation

The Converter does not require any software conguration.

Users can immediately use any feature of this product simply by attached the cables and plug power on. There is some key

limitation on the video over ber converter. Please check the

following items:

The device is used for Point-to-Point connection only (trans-

mitter to receiver) and allows video and data work on the

same optical ber patch cord.

The BNC connector and supports 75 ohm cable. The distance

will change by the quality of coaxial cables.

3.2 Stand-alone Installation

To install a VF-102-T / VF-102-R stand-alone, on a desktop or shelf, simply complete the following steps:

Step 1: Turn off the power of the analog camera / monitor to

which the VF-102-T / VF-102-R will be attached.

Step 2: VF-102-T (Transmitter): Connect coaxial cable from

analog camera to Video BNC port of the VF-102-T.

Step 3: Attach FC single mode ber cable from the VF-102-T to

VF-102-R in the remote side.

Step 4: VF-102-R (Receiver): Connect coaxial cable from

Speed Dome

DVR / Monitor

Control Keyboard

Fiber-optic

Audio Line / Video Line

A/V

Serial Line (RS-485)

|O|O|

A/V

|O|O|

A/V

|O|O|

A/VA/V

Up to 20km

Coax

VF-102-T

Transmitter

VF-102-R

Receiver

monitor / DVR to Video BNC port of the VF-102-R.

Step 5: Connect the 5VDC power adapter to the VF-102-T / VF-

102-R and verify that the Power LED lights up.

Step 6: Turn on the power of the analog camera / monitor; the

VIDEO LED (Green) should light when all cables are attached.

Figure 3-1 VF-102-T / VF-102-R stand alone installation

3.3 Chassis Installation and Rack Mounting

To install the Video over ber Converter in a 10-inch or 19-inch Converter Chassis with standard rack, follow the

instructions described below.

Step 1: Place your Converter Chassis on a hard at surface,

with the front panel positioned towards your front side.

Step 2: Carefully slide in the VF module until it is fully and

rmly tted into the slot of the converter chassis.

Figure 3-2 Insert a video over ber converter into an available slot

Step 3: Attach a rack-mount bracket to each side of the

Control Keyboard

|O|O|

VF-102-T

VF-102-R

DVR / Monitor

Media Converter Chassis

Camera

Speed Dome

100

A/V

|O|O|

A/V

Coax

Fiber-optic

Audio Line / Video Line

A/V

Serial Line (RS-485)

|O|O|

Converter Chassis with supplied screws attached to the package.

Step 4: After the brackets are attached to the Converter

Chassis, use suitable screws to securely attach the brackets to the rack.

Step 5: Proceed with the steps 4 and steps 5 of session 3.2

Stand-alone Installation to connect the video and

ber cabling and supply power to your Converter

Chassis.

3.4 Optional - DIN-Rail mounting

There are two DIN-Rail holes on the left side of the VF-102-T/ VF-102R that allows the converter can be easily installed with DIN-Rail mounting. The PLANET optional DIN-Rail mounting Kit – RKE-DIN can be order separately. When need to replace the wall mount application with DIN-Rail application on the VF-102-T

/ VF-102-R, please refer to following gures to screw the DIN-

Rail on the converter. To hang the VF-102-T / VF-102-R, follow the below steps:

Step 1: screw the DIN-Rail on the VF-102-T / VF-102-R.

Step 2: Lightly press the button of DIN-Rail into the track.

Step 3: Check the DIN-Rail is tightly on the track.

You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would violate your warranty.

4 POWER INFORMATION

The power jack of VF-102-T / VF-102-R is with 2.5mm in the central post and required +5VDC power input. It will conform to the bundled AC-DC adapter and Planet’s Media Chassis. Should you have the issue to make the power connection, please contact your local sales representative.

Please keep the AC-DC adapter as spare parts when your VF102 is installed to a Media Chassis.

2.5mm DC Receptacle 2.5mm +5V for each slot

DC receptacle is 2.5mm wide that conforms to and matches the Video over Fiber Converter 2.5mm DC jack’s central post. Do not install any improper unit, model of the Video over Fiber Converter.

PLANET VF-102-KIT User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual