Planet SGSW-24040, SGSW-24040P4, SGSW-24240, SGSW-24240R, SGSW-24040HP User Manual

User’s Manual of SGSW-24040 / 24240 Series

SGSW-24040 / SGSW -24040R

24-Port 10/100/1000Mbps

User’s Manual

Layer 2 Managed Stackable Switch

SGSW-24040P / SGSW-24040P4

24G PoE Layer2 Managed Stackable Switch

SGSW-24240 / SGSW -24240R

24-Port 100/1000 SFP Fiber
Layer2 Managed Stackable Switch

SGSW-24040HP

24G High PoE Layer2 Managed Stackable Switch

1

User’s Manual of SGSW-24040 / 24240 Series

Trademarks

Copyright © PLANET Technology Corp. 2012.
Contents subject to which revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no
warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for
a particular purpose. PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability
for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes
no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to
this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at whose own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be
required to take adequate measures.

Energy Saving Note of the Device

This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from the power circuit.
Without removing power cable, the device will still consuming power from the power source. In the view of Saving the Energy
and reduce the unnecessary power consuming, it is strongly suggested to remove the power connection for the device if this
device is not intended to be active.

WEEE Warning

To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.

UL Warning

The PLANET SGSW-24040P / 24040P4 have IEEE 802.3af PoE function and comply with UL safety, in order to comply
with UL specification, please refer to UL’s PoE rule as below table:

Clause Title Marking or Instruction Details

PoE Installation
Instruction

PoE Provide
Maximum Power

Description of “The PoE is intended to be connected to
not exposed (outside plant) network” or equivalent
installation instructions.
Statement of PoE is capable of providing maximum power
in installation instructions. See Enclosure User’s Manual
for detail.

2

User’s Manual of SGSW-24040 / 24240 Series

This equipment is only to be connected to PoE networks without routing to outside plant.

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the

rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in

an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe

operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due

to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect

that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given

to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

Revision

PLANET 24-Port 10/100/1000Mbps with 4 Shared SFP / 24 100/1000 SFP Slots with 8 Shared TP Managed Stackable Switch

User's Manual

FOR MODELS: SGSW-24040 / SGSW-24240 Series

REVISION: 1.7 (AUGUST.2012)

Part No: EM-SGSW-24040_24240 Series (2080-A93070-005)

3

User’s Manual of SGSW-24040 / 24240 Series

TABLE OF CONETNTS

1. INTRODUTION ....................................................................................................................20

1.1 Packet Contents .........................................................................................................................................20

1.2 Product Description.....................................................................................................................................1

1.3 How to Use This Manual..............................................................................................................................2

1.4 Product Features..........................................................................................................................................3

1.5 Product Specification ..................................................................................................................................6

2. INSTALLATION ...................................................................................................................14

2.1 Hardware Description................................................................................................................................14

2.1.1 Switch Front Panel ..............................................................................................................................................14

2.1.2 LED Indications ...................................................................................................................................................16

2.1.3 Switch Rear Panel ...............................................................................................................................................20

2.2 Install the Switch........................................................................................................................................23

2.2.1 Desktop Installation .............................................................................................................................................23

2.2.2 Rack Mounting.....................................................................................................................................................24

2.2.3 Installing the SFP transceiver ..............................................................................................................................25

2.2.4 Connecting DC Power Supply .............................................................................................................................27

2.3 Stack Installation........................................................................................................................................29

2.3.1 Connecting Stacking cable ..................................................................................................................................30

2.3.2 Management Stacking .........................................................................................................................................30

3. SWITCH MANAGEMENT.................................................................................................... 33

3.1 Requirements..............................................................................................................................................33

3.2 Management Access Overview.................................................................................................................34

3.3 Administration Console.............................................................................................................................34

3.4 Web Management.......................................................................................................................................36

3.5 SNMP-Based Network Management.........................................................................................................38

4. WEB CONFIGURATION...................................................................................................... 39

4.1 Main Web Page...........................................................................................................................................42

4.2 System.........................................................................................................................................................44

4

User’s Manual of SGSW-24040 / 24240 Series

4.2.1 System Information..............................................................................................................................................45

4.2.2 IP Configuration...................................................................................................................................................46

4.2.3 IPv6 Configuration ...............................................................................................................................................47

4.2.4 Users Configuration .............................................................................................................................................48

4.2.5 Users Privilege Levels .........................................................................................................................................51

4.2.6 NTP Configuration ...............................................................................................................................................53

4.2.7 UPnP Configuration.............................................................................................................................................54

4.2.8 DHCP Relay ........................................................................................................................................................55

4.2.9 DHCP Relay Statistics .........................................................................................................................................57

4.2.10 CPU Load ..........................................................................................................................................................59

4.2.11 System Log........................................................................................................................................................60

4.2.12 Detailed Log ......................................................................................................................................................61

4.2.13 Remote Syslog ..................................................................................................................................................62

4.2.14 SMTP Configure ................................................................................................................................................63

4.2.15 Web Firmware Upgrade.....................................................................................................................................64

4.2.16 TFTP Firmware Upgrade ...................................................................................................................................65

4.2.17 Configuration Backup ........................................................................................................................................66

4.2.18 Configuration Upload.........................................................................................................................................68

4.2.19 Factory Default ..................................................................................................................................................69

4.2.20 System Reboot ..................................................................................................................................................70

4.3 Simple Network Management Protocol....................................................................................................71

4.3.1 SNMP Overview ..................................................................................................................................................71

4.3.2 SNMP System Configuration ...............................................................................................................................72

4.3.3 SNMP System Information Configuration ............................................................................................................73

4.3.4 SNMP Trap Configuration....................................................................................................................................74

4.3.5 SNMPv3 Configuration ........................................................................................................................................76

4.3.5.1 SNMPv3 Communities Configuration ........................................................................................................76

4.3.5.2 SNMPv3 Users Configuration....................................................................................................................77

4.3.5.3 SNMPv3 Groups Configuration .................................................................................................................79

4.3.5.4 SNMPv3 Views Configuration....................................................................................................................80

4.3.5.5 SNMPv3 Accesses Configuration..............................................................................................................81

4.4 Port Management .......................................................................................................................................83

4.4.1 Port Configuration................................................................................................................................................83

4.4.2 Port Statistics Overview.......................................................................................................................................85

4.4.3 Port Statistics Detail.............................................................................................................................................86

4.4.4 SFP Module Information ......................................................................................................................................88

4.4.5 Port Mirroring Configuration.................................................................................................................................90

4.5 Link Aggregation........................................................................................................................................93

4.5.1 Static Aggregation Configuration .........................................................................................................................95

5

User’s Manual of SGSW-24040 / 24240 Series

4.5.2 LACP Configuration.............................................................................................................................................97

4.5.3 LACP System Status ...........................................................................................................................................98

4.5.4 LACP Port Status.................................................................................................................................................99

4.5.5 LACP Port Statistics...........................................................................................................................................101

4.6 VLAN..........................................................................................................................................................102

4.6.1 VLAN Overview .................................................................................................................................................102

4.6.2 IEEE 802.1Q VLAN ...........................................................................................................................................102

4.6.3 VLAN Basic Information.....................................................................................................................................106

4.6.4 VLAN Port Configuration ...................................................................................................................................107

4.6.5 VLAN Membership Configuration ...................................................................................................................... 111

4.6.6 VLAN Membership Status for User Static .......................................................................................................... 112

4.6.7 VLAN Port Status for User Static .......................................................................................................................113

4.6.8 Port Isolation Configuration ...............................................................................................................................115

4.6.9 Private VLAN Membership Configuration .......................................................................................................... 117

4.6.10 VLAN setting example: .................................................................................................................................... 119

4.6.10.1 Two separate 802.1Q VLAN.................................................................................................................. 119

4.6.10.2 VLAN Trunking between two 802.1Q aware switch............................................................................... 123

4.6.10.3 Port Isolate ............................................................................................................................................124

4.7 Spanning Tree Protocol...........................................................................................................................127

4.7.1 Theory ...............................................................................................................................................................127

4.7.2 STP Bridge Configuration ..................................................................................................................................133

4.7.3 Bridge Status .....................................................................................................................................................135

4.7.4 CIST Port Configuration.....................................................................................................................................136

4.7.5 MSTI Priorities ...................................................................................................................................................139

4.7.6 MSTI Configuration............................................................................................................................................140

4.7.7 MSTI Ports Configuration ..................................................................................................................................141

4.7.8 Port Status......................................................................................................................................................... 144

4.7.9 Port Statistics.....................................................................................................................................................145

4.8 Multicast....................................................................................................................................................147

4.8.1 IGMP Snooping .................................................................................................................................................147

4.8.2 IGMP Snooping Configuration ...........................................................................................................................151

4.8.3 IGMP Port Related Configuration ......................................................................................................................152

4.8.4 VLAN Configuration...........................................................................................................................................153

4.8.5 Port Group Filtering ...........................................................................................................................................154

4.8.6 IGMP Snooping Status ......................................................................................................................................155

4.8.7 MVR Configuration ............................................................................................................................................157

4.8.8 MVR Status........................................................................................................................................................159

4.9 Quality of Service.....................................................................................................................................161

6

User’s Manual of SGSW-24040 / 24240 Series

4.9.1 Understand QOS ...............................................................................................................................................161

4.9.2 QCL Configuration Wizard................................................................................................................................. 162

4.9.2.1 Set up Policy Rules .................................................................................................................................163

4.9.2.2 Set up Typical Network Application Rules ...............................................................................................164

4.9.2.3 Set up ToS Precedence Mapping ............................................................................................................ 166

4.9.2.4 Set up VLAN Tag Priority Mapping ..........................................................................................................168

4.9.3 QoS Control List Configuration ..........................................................................................................................169

4.9.3.1 QoS Control Entry Configuration .............................................................................................................170

4.9.4 Port QoS Configuration......................................................................................................................................171

4.9.5 Bandwidth Control .............................................................................................................................................173

4.9.6 Storm Control Configuration ..............................................................................................................................175

4.9.7 QoS Statistics ....................................................................................................................................................176

4.9.8 DSCP Remarking ..............................................................................................................................................177

4.9.9 Voice VLAN Configuration .................................................................................................................................179

4.9.10 Voice VLAN OUI Table.....................................................................................................................................182

4.10 Access Control Lists..............................................................................................................................183

4.10.1 Access Control List Status ...............................................................................................................................183

4.10.2 Access Control List Configuration....................................................................................................................184

4.10.3 ACE Configuration ...........................................................................................................................................186

4.10.4 ACL Ports Configuration ..................................................................................................................................194

4.10.5 ACL Rate Limiter Configuration .......................................................................................................................197

4.11 Authentication.........................................................................................................................................198

4.11.1 Understanding IEEE 802.1X Port-Based Authentication..................................................................................199

4.11.2 Authentication Configuration ............................................................................................................................202

4.11.3 Network Access Server Configuration..............................................................................................................203

4.11.4 Network Access Overview ...............................................................................................................................214

4.11.5 Network Access Statistics ................................................................................................................................215

4.11.6 Authentication Server Configuration.................................................................................................................222

4.11.7 RADIUS Overview ...........................................................................................................................................225

4.11.8 RADIUS Details ...............................................................................................................................................227

4.11.9 Windows Platform RADIUS Server Configuration............................................................................................233

4.11.10 802.1X Client Configuration ...........................................................................................................................238

4.12 Security ...................................................................................................................................................241

4.12.1 Port Limit Control.............................................................................................................................................241

4.12.2 Access Management .......................................................................................................................................245

4.12.3 Access Management Statistics ........................................................................................................................246

4.12.4 HTTPs .............................................................................................................................................................247

4.12.5 SSH ................................................................................................................................................................. 247

4.12.6 Port Security Status.........................................................................................................................................248

7

User’s Manual of SGSW-24040 / 24240 Series

4.12.7 Port Security Detail..........................................................................................................................................251

4.12.8 DHCP Snooping ..............................................................................................................................................252

4.12.9 DHCP Snooping Statistics ...............................................................................................................................253

4.12.10 IP Source Guard Configuration......................................................................................................................255

4.12.11 IP Source Guard Static Table .........................................................................................................................257

4.12.12 ARP Inspection ..............................................................................................................................................258

4.12.13 ARP Inspection Static Table ...........................................................................................................................259

4.13 Address Table.........................................................................................................................................261

4.13.1 MAC Address Table Configuration ...................................................................................................................261

4.13.2 Static MAC Table Configuration ....................................................................................................................... 262

4.13.3 MAC Address Table Status ..............................................................................................................................263

4.13.4 MAC Table Learning ........................................................................................................................................264

4.13.5 Dynamic ARP Inspection Table ........................................................................................................................266

4.13.6 Dynamic IP Source Guard Table......................................................................................................................267

4.14 LLDP........................................................................................................................................................269

4.14.1 Link Layer Discovery Protocol .........................................................................................................................269

4.14.2 LLDP Configuration .........................................................................................................................................269

4.14.3 LLDPMED Configuration .................................................................................................................................273

4.14.4 LLDP-MED Neighbor.......................................................................................................................................279

4.14.5 Neighbor ..........................................................................................................................................................282

4.14.6 Port Statistics...................................................................................................................................................284

4.15 Network Diagnostics..............................................................................................................................286

4.15.1 Ping .................................................................................................................................................................287

4.15.2 IPv6 Ping .........................................................................................................................................................288

4.15.3 Remote IP Ping Test ........................................................................................................................................289

4.15.4 Cable Diagnostics............................................................................................................................................290

4.16 Power over Ethernet (SGSW-24040P / SGSW-24040P4 / SGSW-24040HP) ......................................292

4.16.1 Power over Ethernet Powered Device.............................................................................................................293

4.16.2 Power Configuration ........................................................................................................................................293

4.16.3 Port Configuration............................................................................................................................................296

4.16.4 PoE Status.......................................................................................................................................................299

4.16.5 PoE Schedule..................................................................................................................................................301

4.16.6 LLDP Neighbor Power Over Ethernet..............................................................................................................302

4.17 Stack........................................................................................................................................................304

4.17.1 Stack................................................................................................................................................................306

4.17.1.1 Switch IDs...........................................................................................................................................306

4.17.1.2 Master Election ...................................................................................................................................307

4.17.1.3 Stack Redundancy..............................................................................................................................307

8

User’s Manual of SGSW-24040 / 24240 Series

4.17.1.4 Shortest Path Forwarding ...................................................................................................................308

4.17.2 Stack Configuration .........................................................................................................................................309

4.17.3 Stack Information.............................................................................................................................................312

4.17.4 Stack Port State Ovewview ..............................................................................................................................313

4.17.5 Stack Example.................................................................................................................................................313

5. COMMAND LINE INTERFACE..........................................................................................317

5.1 Accessing the CLI ....................................................................................................................................317

Logon to the Console ..........................................................................................................................................317

Configure IP address...........................................................................................................................................318

5.2 Telnet Login ..............................................................................................................................................320

6. Command Line Mode.......................................................................................................321

6.1 System Command....................................................................................................................................322

System Configuration ..........................................................................................................................................322

System Name......................................................................................................................................................322

System Contact ...................................................................................................................................................323

System Location..................................................................................................................................................323

System Timezone................................................................................................................................................324

System Prompt....................................................................................................................................................324

System Reboot....................................................................................................................................................325

System Restore Default.......................................................................................................................................325

System Load .......................................................................................................................................................326

System Log .........................................................................................................................................................326

6.2 Stack..........................................................................................................................................................328

Stack List.............................................................................................................................................................328

Stack Master Priority ...........................................................................................................................................328

Stack Master Reelect...........................................................................................................................................329

Stack Select.........................................................................................................................................................329

Stack SID Swap...................................................................................................................................................329

Stack SID Delete .................................................................................................................................................330

Stack SID Assign .................................................................................................................................................330

6.3 IP Command..............................................................................................................................................332

IP Configuration...................................................................................................................................................332

IP DHCP..............................................................................................................................................................332

IP Setup...............................................................................................................................................................333

IP Ping.................................................................................................................................................................334

IP DNS ................................................................................................................................................................334

9

User’s Manual of SGSW-24040 / 24240 Series

IP DNS Proxy ......................................................................................................................................................335

IPv6 AUTOCINFIG ..............................................................................................................................................335

IPv6 Setup...........................................................................................................................................................336

IPv6 Ping .............................................................................................................................................................336

IP NTP Configuration...........................................................................................................................................337

IP NTP Mode....................................................................................................................................................... 338

IP NTP Server Add ..............................................................................................................................................338

IP NTP Server IPv6 Add ......................................................................................................................................339

IP NTP Server Delete..........................................................................................................................................339

6.4 Port Management Command...................................................................................................................340

Port Configuration ...............................................................................................................................................340

Port Mode............................................................................................................................................................340

Port Flow Control.................................................................................................................................................341

Port State.............................................................................................................................................................342

Port Maximum Frame..........................................................................................................................................342

Port Power...........................................................................................................................................................343

Port SFP..............................................................................................................................................................343

Port Excessive.....................................................................................................................................................344

Port Statistics.......................................................................................................................................................344

Port VeriPHY .......................................................................................................................................................345

6.5 MAC Address Table Command...............................................................................................................346

MAC Configuration ..............................................................................................................................................346

MAC Add .............................................................................................................................................................347

MAC Delete .........................................................................................................................................................347

MAC Lookup........................................................................................................................................................348

MAC Age Time ....................................................................................................................................................348

MAC Learning .....................................................................................................................................................349

MAC Dump..........................................................................................................................................................349

MAC Statistics .....................................................................................................................................................350

MAC Flush...........................................................................................................................................................351

6.6 VLAN Configuration Command ..............................................................................................................352

VLAN Configuration.............................................................................................................................................352

VLAV PVID ..........................................................................................................................................................352

VLAN Frame Type...............................................................................................................................................353

VLAN Ingress Filter .............................................................................................................................................353

VLAN Mode .........................................................................................................................................................354

VLAN Link Type...................................................................................................................................................354

VLAN Q-in-Q Mode .............................................................................................................................................355

VLAN Ethernet Type............................................................................................................................................356

10

User’s Manual of SGSW-24040 / 24240 Series

VLAN Add............................................................................................................................................................356

VLAN Delete........................................................................................................................................................357

VLAN Lookup ......................................................................................................................................................357

VLAN Status........................................................................................................................................................358

6.7 Private VLAN Configuration Command.................................................................................................360

PVLAN Configuration ..........................................................................................................................................360

PVLAN Add .........................................................................................................................................................361

PVLAN Delete .....................................................................................................................................................361

PVLAN Lookup....................................................................................................................................................362

PVLAN Isolate .....................................................................................................................................................362

6.8 Security Command...................................................................................................................................364

Security Switch User Configuration .....................................................................................................................364

Security Switch User Add ....................................................................................................................................364

Security Switch User Delete................................................................................................................................365

Security Switch Privilege Level Configuration .....................................................................................................365

Security Switch Privilege Level Group.................................................................................................................366

Security Switch Privilege Level Current...............................................................................................................367

Security Switch Auth Configuration .....................................................................................................................367

Security Switch Auth Method...............................................................................................................................368

Security Switch SSH Configuration .....................................................................................................................369

Security Switch SSH Mode..................................................................................................................................369

Security Switch HTTPs Configuration .................................................................................................................370

Security Switch HTTPs Mode..............................................................................................................................370

Security Switch HTTPs Redirect .........................................................................................................................371

Security Switch Access Configuration .................................................................................................................371

Security Switch Access Mode..............................................................................................................................372

Security Switch Access Add ................................................................................................................................372

Security Switch Access IPv6 Add ........................................................................................................................373

Security Switch Access Delete ............................................................................................................................374

Security Switch Access Lookup ...........................................................................................................................374

Security Switch Access Clear .............................................................................................................................. 374

Security Switch Access Statistics ........................................................................................................................375

Security Switch SNMP Configuration ..................................................................................................................375

Security Switch SNMP Mode...............................................................................................................................377

Security Switch SNMP Version............................................................................................................................378

Security Switch SNMP Read Community............................................................................................................378

Security Switch SNMP Write Community ............................................................................................................379

Security Switch SNMP Trap Mode.......................................................................................................................379

Security Switch SNMP Trap Version....................................................................................................................380

11

User’s Manual of SGSW-24040 / 24240 Series

Security Switch SNMP Trap Community .............................................................................................................380

Security Switch SNMP Trap Destination..............................................................................................................381

Security Switch SNMP Trap IPv6 Destination .....................................................................................................381

Security Switch SNMP Trap Authentication Failure .............................................................................................382

Security Switch SNMP Trap Link-up....................................................................................................................382

Security Switch SNMP Trap Inform Mode ...........................................................................................................383

Security Switch SNMP Trap Inform Timeout........................................................................................................384

Security Switch SNMP Trap Inform Retry Times .................................................................................................384

Security Switch SNMP Trap Probe Security Engine ID .......................................................................................385

Security Switch SNMP Trap Security Engine ID..................................................................................................385

Security Switch SNMP Trap Security Name........................................................................................................386

Security Switch SNMP Engine ID........................................................................................................................386

Security Switch SNMP Community Add ..............................................................................................................386

Security Switch SNMP Community Delete ..........................................................................................................387

Security Switch SNMP Community Lookup.........................................................................................................387

Security Switch SNMP User Add......................................................................................................................... 388

Security Switch SNMP User Delete.....................................................................................................................389

Security Switch SNMP User Changekey.............................................................................................................389

Security Switch SNMP User Lookup ...................................................................................................................389

Security Switch SNMP Group Add.......................................................................................................................390

Security Switch SNMP Group Delete ..................................................................................................................391

Security Switch SNMP Group Lookup.................................................................................................................391

Security Switch SNMP View Add .........................................................................................................................392

Security Switch SNMP View Delete.....................................................................................................................392

Security Switch SNMP View Lookup ...................................................................................................................392

Security Switch SNMP Access Add .....................................................................................................................393

Security Switch SNMP Access Delete.................................................................................................................394

Security Switch SNMP Access Lookup................................................................................................................394

Security Network Psec Switch.............................................................................................................................395

Security Network Psec Port.................................................................................................................................396

Security Network Limit Configuration ..................................................................................................................397

Security Network Limit Mode...............................................................................................................................398

Security Network Limit Aging...............................................................................................................................398

Security Network Limit Agetime...........................................................................................................................399

Security Network Limit Port .................................................................................................................................399

Security Network Limit Limit ................................................................................................................................400

Security Network Limit Action..............................................................................................................................401

Security Network Limit Reopen ...........................................................................................................................401

Security Network NAS Configuration...................................................................................................................402

Security Network NAS Mode ...............................................................................................................................402

12

User’s Manual of SGSW-24040 / 24240 Series

Security Network NAS State................................................................................................................................403

Security Network NAS Reauthentication .............................................................................................................404

Security Network NAS ReauthPeriod ..................................................................................................................404

Security Network NAS EapolTimeout..................................................................................................................405

Security Network NAS Agetime...........................................................................................................................405

Security Network NAS Holdtime..........................................................................................................................406

Security Network NAS RADIUS_QoS .................................................................................................................406

Security Network NAS RADIUS_VLAN ............................................................................................................... 407

Security Network NAS Guest_VLAN ...................................................................................................................408

Security Network NAS Authenticate ....................................................................................................................408

Security Network NAS Statistics..........................................................................................................................409

Security Network ACL Configuration ...................................................................................................................410

Security Network ACL Action...............................................................................................................................411

Security Network ACL Policy ...............................................................................................................................412

Security Network ACL Rate .................................................................................................................................413

Security Network ACL Add ..................................................................................................................................413

Security Network ACL Delete ..............................................................................................................................415

Security Network ACL Lookup .............................................................................................................................415

Security Network ACL Clear ................................................................................................................................415

Security Network ACL Status...............................................................................................................................416

Security Network DHCP Relay Configuration......................................................................................................416

Security Network DHCP Relay Mode .................................................................................................................. 417

Security Network DHCP Relay Server.................................................................................................................418

Security Network DHCP Relay Information Mode ...............................................................................................418

Security Network DHCP Relay Information Policy...............................................................................................419

Security Network DHCP Relay Statistics.............................................................................................................419

Security Network DHCP Snooping Configuration................................................................................................420

Security Network DHCP Snooping Mode ............................................................................................................421

Security Network DHCP Snooping Port Mode.....................................................................................................421

Security Network DHCP Snooping Statistics .......................................................................................................422

Security Network IP Source Guard Configuration ...............................................................................................423

Security Network IP Source Guard Mode............................................................................................................424

Security Network IP Source Guard Port Mode ....................................................................................................425

Security Network IP Source Guard Limit .............................................................................................................425

Security Network IP Source Guard Entry ............................................................................................................426

Security Network IP Source Guard Status...........................................................................................................426

Security Network ARP Inspection Configuration..................................................................................................427

Security Network ARP Inspection Mode..............................................................................................................427

Security Network ARP Inspection Port Mode ......................................................................................................428

Security Network ARP Inspection Entry...............................................................................................................428

13

User’s Manual of SGSW-24040 / 24240 Series

Security Network ARP Inspection Status .............................................................................................................429

Security AAA Configuration .................................................................................................................................429

Security AAA Timeout..........................................................................................................................................430

Security AAA Deadtime .......................................................................................................................................431

Security AAA RADIUS.........................................................................................................................................431

Security AAA ACCT_RADIUS..............................................................................................................................432

Security AAA TACACS+ ......................................................................................................................................433

Security AAA Statistics.........................................................................................................................................433

6.9 Spanning Tree Protocol Command ........................................................................................................435

STP Configuration ...............................................................................................................................................435

STP Version ........................................................................................................................................................435

STP Tx Hold ........................................................................................................................................................436

STP MaxHops .....................................................................................................................................................436

STP MaxAge .......................................................................................................................................................437

STP FwdDelay ....................................................................................................................................................437

STP CName ........................................................................................................................................................438

STP BPDU Filter..................................................................................................................................................438

STP BPDU Guard................................................................................................................................................439

STP Recovery .....................................................................................................................................................439

STP Status ..........................................................................................................................................................440

STP MSTI Priority................................................................................................................................................441

STP MSTI Map....................................................................................................................................................441

STP MSTI Add.....................................................................................................................................................442

STP Port Configuration........................................................................................................................................442

STP Port Mode....................................................................................................................................................443

STP Port Edge ....................................................................................................................................................443

STP Port AutoEdge .............................................................................................................................................444

STP Port P2P ......................................................................................................................................................444

STP Port RestrictedRole .....................................................................................................................................445

STP Port RestrictedTcn .......................................................................................................................................445

STP Port bpduGuard...........................................................................................................................................446

STP Port Statistic.................................................................................................................................................446

STP Port Mcheck.................................................................................................................................................447

STP MSTI Port Configuration ..............................................................................................................................447

STP MSTI Port Cost............................................................................................................................................448

STP MSTI Port Priority ........................................................................................................................................449

6.10 Multicast Configuration Command ......................................................................................................450

IGMP Configuration.............................................................................................................................................450

IGMP Mode .........................................................................................................................................................450

14

User’s Manual of SGSW-24040 / 24240 Series

IGMP Leave Proxy ..............................................................................................................................................451

IGMP State ..........................................................................................................................................................451

IGMP Querier ......................................................................................................................................................452

IGMP Fastleave...................................................................................................................................................452

IGMP Throttling ...................................................................................................................................................453

IGMP Filtering .....................................................................................................................................................453

IGMP Router .......................................................................................................................................................454

IGMP Flooding ....................................................................................................................................................455

IGMP Groups.......................................................................................................................................................455

IGMP Status ........................................................................................................................................................455

6.11 Link Aggregation Command .................................................................................................................457

Aggregation Configuration...................................................................................................................................457

Aggregation Add..................................................................................................................................................457

Aggregation Delete..............................................................................................................................................458

Aggregation Lookup ............................................................................................................................................458

Aggregation Mode ...............................................................................................................................................459

6.12 Link Aggregation Control Protocol Command....................................................................................460

LACP Configuration.............................................................................................................................................460

LACP Mode .........................................................................................................................................................461

LACP Key............................................................................................................................................................461

LACP Role...........................................................................................................................................................462

LACP Status ........................................................................................................................................................462

LACP Statistics....................................................................................................................................................463

6.13 LLDP Command......................................................................................................................................464

LLDP Configuration .............................................................................................................................................464

LLDP Mode .........................................................................................................................................................464

LLDP Optional TLV..............................................................................................................................................465

LLDP Interval.......................................................................................................................................................466

LLDP Hold ...........................................................................................................................................................466

LLDP Delay .........................................................................................................................................................467

LLDP Reinit .........................................................................................................................................................467

LLDP Statistics ....................................................................................................................................................468

LLDP Info ............................................................................................................................................................469

LLDP CDP Aware ................................................................................................................................................469

6.14 LLDPMED Command .............................................................................................................................470

LLDPMED Configuration .....................................................................................................................................470

LLDPMED Civic...................................................................................................................................................470

LLDPMED ECS ...................................................................................................................................................471

15

User’s Manual of SGSW-24040 / 24240 Series

LLDPMED Policy Delete......................................................................................................................................472

LLDPMED Policy Add..........................................................................................................................................472

LLDPMED Port Policy .........................................................................................................................................473

LLDPMED Coordinates .......................................................................................................................................474

LLDPMED Datum................................................................................................................................................474

LLDPMED Fast ...................................................................................................................................................475

LLDPMED Info ....................................................................................................................................................475

LLDPMED Debuge_med_transmit_var ...............................................................................................................475

6.15 Power over Ethernet Command............................................................................................................476

PoE Configuration ...............................................................................................................................................476

PoE Mode............................................................................................................................................................477

PoE Priority .........................................................................................................................................................477

PoE Mamagement Mode.....................................................................................................................................478

PoE Maximum Power..........................................................................................................................................479

PoE Allocated Power...........................................................................................................................................479

PoE Power Supply ..............................................................................................................................................480

PoE Status...........................................................................................................................................................480

6.16 Quality of Service Command ................................................................................................................481

QoS Configuration...............................................................................................................................................481

QoS Classes .......................................................................................................................................................481

QoS Default.........................................................................................................................................................482

QoS Tag Priority ..................................................................................................................................................482

QoS QCL Port .....................................................................................................................................................483

QoS QCL Add......................................................................................................................................................483

QoS QCL Delete..................................................................................................................................................484

QoS QCL Lookup ................................................................................................................................................485

QoS Mode ...........................................................................................................................................................485

QoS Weight .........................................................................................................................................................485

QoS Rate Limiter.................................................................................................................................................486

QoS Shaper.........................................................................................................................................................486

QoS Storm Unicast..............................................................................................................................................487

QoS Strom Multicast............................................................................................................................................487

QoS Strom Broadcast..........................................................................................................................................488

QoS DSCP Remarking ........................................................................................................................................489

QoS DSCP Queue Mapping................................................................................................................................489

6.17 Mirror Command ....................................................................................................................................490

Mirror Configuration.............................................................................................................................................490

Mirror Port ...........................................................................................................................................................490

Mirror SID ............................................................................................................................................................491

16

User’s Manual of SGSW-24040 / 24240 Series

Mirror Mode .........................................................................................................................................................491

6.18 Configuration Command.......................................................................................................................493

Configuration Save..............................................................................................................................................493

Configuration Load ..............................................................................................................................................493

6.19 Firmware Command...............................................................................................................................494

Firmware Load ....................................................................................................................................................494

Firmware IPv6 Load ............................................................................................................................................494

6.20 UPnP Command .....................................................................................................................................495

UPnP Configuration.............................................................................................................................................495

UPnP Mode .........................................................................................................................................................495

UPnP TTL............................................................................................................................................................496

UPnP Advertising Duration ..................................................................................................................................496

6.21 MVR Command.......................................................................................................................................497

MVR Configuration ..............................................................................................................................................497

MVR Group .........................................................................................................................................................498

MVR Status .........................................................................................................................................................498

MVR Mode ..........................................................................................................................................................498

MVR Port Mode...................................................................................................................................................499

MVR Multicast VLAN...........................................................................................................................................499

MVR Port Type....................................................................................................................................................500

MVR Immediate Leave ........................................................................................................................................500

6.22 Voice VLAN Command...........................................................................................................................502

Voice VLAN Configuration...................................................................................................................................502

Voice VLAN Mode ...............................................................................................................................................503

Voice VLAN ID.....................................................................................................................................................504

Voice VLAN Agetime ...........................................................................................................................................504

Voice VLAN Traffic Class.....................................................................................................................................505

Voice VLAN OUI Add...........................................................................................................................................505

Voice VLAN OUI Delete.......................................................................................................................................506

Voice VLAN OUI Clear ........................................................................................................................................506

Voice VLAN OUI Lookup.....................................................................................................................................507

Voice VLAN Port Mode........................................................................................................................................507

Voice VLAN Security ...........................................................................................................................................508

6.23 SMTP Command.....................................................................................................................................509

SMTP Configuration ............................................................................................................................................509

SMTP Mode ........................................................................................................................................................509

SMTP Server.......................................................................................................................................................509

17

User’s Manual of SGSW-24040 / 24240 Series

SMTP Auth ..........................................................................................................................................................510

SMTP Auth_user .................................................................................................................................................510

SMTP Auth_pass................................................................................................................................................. 511

SMTP Mailfrom.................................................................................................................................................... 511

SMTP Mailsubject................................................................................................................................................511

SMTP Mailto1......................................................................................................................................................512

SMTP Mailto2......................................................................................................................................................512

6.24 Show Command .....................................................................................................................................513

Show ACL Configuration .....................................................................................................................................513

Show Link Aggregation Configuration .................................................................................................................513

Show IGMP Configuration ...................................................................................................................................513

Show IP Configuration.........................................................................................................................................513

Show LACP Configuration...................................................................................................................................514

Show LLDP Configuration ...................................................................................................................................514

Show MAC Configuration ....................................................................................................................................514

Show Mirror Configuration...................................................................................................................................514

Show PoE Configuration .....................................................................................................................................514

Show Port Configuration......................................................................................................................................515

Show Private VLAN Configuration.......................................................................................................................515

Show QoS Configuration .....................................................................................................................................515

Show SNMP Configuration..................................................................................................................................515

Show Stack Configuration ...................................................................................................................................516

Show System Configuration ................................................................................................................................516

Show VLAN Configuration...................................................................................................................................516

Show STP Configuration .....................................................................................................................................516

7. SWITCH OPERATION .......................................................................................................517

7.1 Address Table...........................................................................................................................................517

7.2 Learning ....................................................................................................................................................517

7.3 Forwarding & Filtering.............................................................................................................................517

7.4 Store-and-Forward...................................................................................................................................517

7.5 Auto-Negotiation ......................................................................................................................................518

8. POWER OVER ETHERNET OVERVIEW..........................................................................519

What is PoE?...................................................................................................................................................519

The PoE Provision Process...........................................................................................................................521

18

User’s Manual of SGSW-24040 / 24240 Series

Stages of powering up a PoE link...............................................................................................................................521

Line Detection.............................................................................................................................................................521

Classification ..............................................................................................................................................................522

Start-up.......................................................................................................................................................................522

Operation....................................................................................................................................................................522

Power Disconnection Scenarios .................................................................................................................................522

9. TROUBLE SHOOTING...................................................................................................... 524

APPENDEX A........................................................................................................................526

A.1 Switch's RJ-45 Pin Assignments ...........................................................................................................526

A.2 10/100Mbps, 10/100Base-TX...................................................................................................................526

APPENDEX B : GLOSSARY................................................................................................. 528

19

User’s Manual of SGSW-24040 / 24240 Series

1. INTRODUTION

The PLANET Layer 2 Managed Gigabit Switch series –SGSW Stackable, SGSW PoE and SGSW Fiber switch are all multiple

ports Gigabit Ethernet Switched with SFP fiber optical connective ability and robust layer 2 features; the description of these

models as below:

SGSW-24040 :
SGSW-24040R :
SGSW-24040P
SGSW-24040P4
SGSW-24240
SGSW-24240R
SGSW-24040HP

Terms of “Managed Switch” means the Switches mentioned titled in the cover page of this User’s manual, i.e. SGSW- series

Managed Switch.

24-Port 10/100/1000Base-T with 4 Shared SFP Managed Stackable Switch

24-Port 10/100/1000Base-T with 4 Shared SFP Managed Stackable Switch / Redundant Power

24-Port 10/100/1000Base-T PoE Managed Stackable Switch / 220W / IEEE 802.3af

24-Port 10/100/1000Base-T PoE Managed Stackable Switch / 380W / IEEE 802.3af

24-Port 100/1000Base-X with 8 Shared TP Managed Stackable Switch

24-Port 100/1000Base-X with 8 Shared TP Managed Stackable Switch / Redundant Power

24-Port 10/100/1000 Base-T PoE Managed Stackable Switch / 360W / IEEE 802.3af/at

1.1 Packet Contents

Open the box of the Managed Switch and carefully unpack it. The box should contain the following items:

Check the contents of your package for following parts:

 The Managed Switch

x1

 User’s manual CD
 Quick installation guide
 19” Rack mount accessory kit
 Power cord
 Rubber feet
 RS-232 DB9 male Console cable
 CB-STX50 – 50cm stack cable

If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the

original packing material, and use them against to repack the product in case there is a need to return it to us for repair.

x1

x1

x1

x1

X4

x1

x1

20

User’s Manual of SGSW-24040 / 24240 Series

1.2 Product Description

Cost-effective IPv6 Managed Gigabit Switch solution for SMB

Nowadays, lots of electronic products or mobile devices can browse the Internet, which means the need of IP Address

increases. However, the current IPv4 network infrastructure is not capable enough to provide IP Address to each single

users/Clients. The situation forces the ISP to build up the IPv6 (Internet Protocol version 6) network infrastructure speedily.
To fulfill the demand, PLANET releases the IPv6 management Gigabit Ethernet Switch, SGSW- series Managed Switch. It

supports both IPv4 and IPv6 management functions. It can work with original network structure (IPv4) and also support the

new network structure (IPv6) in the future. With easy and friendly management interfaces and plenty of management

functions included, the SGSW- series Managed Switch is the best choice for ISP to build the IPv6 FTTx edge service and for

SMB to connect with IPv6 network.

High-Performance / Cost-effective / Telecom class Gigabit solution for Enterprise backbone and Data Center
Networking

The PLANET Managed Switch is a L2/L4 Managed Gigabit Switch. Since Gigabit network interface had become the basic

equipment and requirement of Enterprise and Network Servers, with 48Gbps switching fabric, the Managed Switch can

handle extremely large amounts of data in a secure topology linking to a backbone or high capacity servers. The powerful

QoS and Network Security features make it to meets the needs of effective data traffic control for both Campus and Enterprise,

such VoIP, video streaming and multicast application.

High Performance

The Managed Switch provides 24 10/100/1000Mbps Gigabit Ethernet ports with 4 shared Gigabit SFP slots. It boasts a high

performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as

48Gbps, which greatly simplifies the tasks of upgrading the LAN for catering to increase bandwidth demands.

Robust Layer 2 Features

The Managed Switch can be programmed for basic switch management functions such as port speed configuration, Port

aggregation, VLAN, Spanning Tree protocol, QoS, bandwidth control and IGMP Snooping. The Managed Switch provides

802.1Q Tagged VLAN, Q-in-Q VLAN trunning and private VLAN, the VLAN groups allowed on the Managed Switch will be

maximally up to 255. Via supporting port aggregation, the Managed Switch allows the operation of a high-speed trunk

combining multiple ports, up to eight groups of maximum to 8-ports for trunking, and it supports fail-over as well.

Excellent Traffic Control

The Managed Switch is loaded with powerful traffic management and QoS features to enhance services offered by telecoms.

The functionality includes QoS features such as wire-speed Layer 4 traffic classifiers and bandwidth limiting that are particular

useful for multi-tenant unit, multi business unit, Telco, or Network Service Provide applications. It also empowers the

enterprises to take full advantages of the limited network resources and guarantees the best performance at VoIP and Video

conferencing transmission.

1

User’s Manual of SGSW-24040 / 24240 Series

Efficient Management

For efficient management, the series of Managed Switch is equipped with console, WEB and SNMP management interfaces.

With its built-in Web-based management, it offers an easy-to-use, platform-independent management and configuration

facility. The Managed Switch supports standard Simple Network Management Protocol (SNMP) and can be managed via any

standard-based management software. For text-based management, it can also be accessed via Telnet and the console port.

Powerful Security

The Managed Switch offers comprehensive Access Control List (ACL) for enforcing security to the edge. Its protection

mechanisms also comprise of port-based 802.1x and MAC-based user and device authentication. The port-security is

effective in limit the numbers of clients pass through, so that network administrators can now construct highly secured

corporate networks with time and effort considerably less than before.

Flexibility and Extension solution

The 4 mini-GBIC slots are compatible with 1000Base-SX/LX and WDM SFP(Small Factor Pluggable) fiber-optic modules. The

distance can be extended from 550 meters (Multi-Mode fiber) up to above 10/20/30 /40/50/70/120 kilometers (Single-Mode

fiber or WDM fiber). They are well suited for using within the enterprise data centers and distributions.

Reliability Stacking Management

The SGSW Series Managed Switch provides a switch stacking function to manage up to 16 switches using a single IP

address. That helps network managers to easily configure switches via one single IP address instead of connecting and

setting each unit one by one. Through its high bandwidth tunnel and stacking technology, it gives enterprise, service provider

and telcom flexible control over port density, uplinks and switch stack performance. Up to 384 Gigabit Ethernet ports can be

managed by a stacking group and you can add ports and functionality as needed. The stacking technology also enables the

advantages of chassis-based switches to be integrated into SGSW Series Managed Switch, but without the expensive

up-front cost.

AC / DC Power Redundant to ensure continuous operation

The SGSW-24040R / SGSW-24240R Managed Switch equip with one 100~240V AC power supply unit and one DC -48V

power supply unit on its standard package, it provides redundant power supply installation. A redundant power system is also

provided to enhance the reliability with either 100~240V AC power supply unit or DC -48V power supply unit. The continuous

power systems are specifically designed to handle the demands of high tech facilities requiring the highest power integrity

available.

Advanced Features and Centralized Power Management for Enterprise and Campus PoE Networking (PoE Model)

The PLANET SGSW-24040P series PoE Switch provides 24 10/100/1000Mbps Power-over-Ethernet (PoE, IEEE 802.3af

compliant) ports which optimize the installation and power management of network devices such as wireless access points

(AP), Voice over IP (VoIP) phones, and security video cameras. The PoE capabilities also help to reduce deployment costs for

network devices like the wireless AP as a result of freeing from restrictions of power outlet locations. Power and data

switching are integrated into one unit and delivered over a single cable. It thus eliminates cost for additional AC wiring and

1

User’s Manual of SGSW-24040 / 24240 Series

reduces installation time.

IEEE 802.3at Power over Ethernet Pre-Standard Compliant (SGSW-24040HP only)

Till today, the IEEE 802.3af Power over Ethernet Standard has become popular yet the PoE demand still grows for increasing

network-powered applications. With many critical applications appears, the IEEE 802.3af PoE standard may not afford the

trend of higher power demand. Hence, the IEEE 802.3at Power over Ethernet pre-standard is defined to allow delivery of

maximum up to 30 Watts input power to per PoE device. The IEEE 802.3at Power over Ethernet pre-standard is an ideal

solution to fulfill the high power requirements directly via the RJ-45 Port interface. Compliant with IEEE 802.3at, the

SGSW-24040HP possesses stronger power capability than the existing 802.3af PoE Switch.

The below table lists the major hardware difference between the series model:

Model

(SGSW Series)

Copper 8 24

Interface

Fiber 24, 100FX compatible 4, 100FX compatible

Redundant Power

PoE Mode - af af af / at

PoE Budget

Stack Capability Hardware stacking, up to 16 units

24240 24240R 24040 24040R 24040P 24040P4 24040HP

-

-48V DC

-

(-30V~-60V)

-

-48V DC

-

(-30V~-60V)

220W 380W 360W

1.3 How to Use This Manual

This User Manual is structured as follows:

Section 2, INSTALLATION

The section explains the functions of the Switch and how to physically install the Managed Switch.

Section 3, SWITCH MANAGEMENT

The section contains the information about the software function of the Managed Switch.

Section 4, WEB CONFIGURATION

The section explains how to manage the Managed Switch by Web interface.

Section 5, COMMAND LINE INTERFACE

The section describes how to use the Command Line interface (CLI).

Section 6, CLI CONFIGURATION

The section explains how to manage the Managed Switch by Command Line interface.

Section 7, SWITCH OPERATION

The chapter explains how to does the switch operation of the Managed Switch.

Section 8, POWER OVER ETHERNET OVERVIEW

The chapter introduce the IEEE 802.3af PoE standard and PoE provision of the Managed Switch.

Section 9, TROUBSHOOTING

The chapter explains how to trouble shooting of the Managed Switch.

Appendix A

The section contains cable information of the Managed Switch.

2

User’s Manual of SGSW-24040 / 24240 Series

1.4 Product Features

 Physical Port

SGSW-24040 / SGSW-24040R

 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45
 4 100/1000Base-X SFP slots, shared with Port-21 to Port-24
 RS-232 DB9 console interface for Switch basic management and setup
 2 High-performance 5GbE Stacking interface

SGSW-24040P / SGSW-24040P4 / SGSW-24040HP

 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 with IEEE 802.3af PoE Injector (SGSW-24040P / 24040P4)
 24-Port 10/100/1000Base-T Gigabit Ethernet RJ-45 with IEEE 802.3af / 802.3at PoE Injector (SGSW-24040HP)
 4 100/1000Base-X SFP slots, shared with Port-21 to Port-24
 RS-232 DB9 console interface for Switch basic management and setup
 2 High-performance 5GbE Stacking interface

SGSW-24240 / SGSW-24240R

 24 100/1000Base-X mini-GBIC/SFP slots
 8-Port 10/100/1000Base-T Gigabit Ethernet RJ-45, shared with Port-1 to Port-8
 RS-232 DB9 console interface for Switch basic management and setup
 2 High-performance 5GbE Stacking interface

 Layer 2 Features

■ Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.3x PAUSE frame flow control (Full-Duplex)

■ High performance of Store-and-Forward architecture, broadcast storm control and runt/CRC filtering eliminates

erroneous packets to optimize the network bandwidth

■ Storm Control support:

 Broadcast / Multicast / Unknown-Unicast

■ Support VLAN

 IEEE 802.1Q Tagged VLAN

 Up to 255 VLANs groups, out of 4094 VLAN IDs

 Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)

 Private VLAN Edge (PVE)

 Voice VLAN

■ Support Spanning Tree Protocol

 STP, IEEE 802.1D Spanning Tree Protocol

 RSTP, IEEE 802.1w Rapid Spanning Tree Protocol

 MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN

 BPDU Guard

■ Support Link Aggregation

3

User’s Manual of SGSW-24040 / 24240 Series

 802.3ad Link Aggregation Control Protocol (LACP)

 Cisco ether-channel (Static Trunk)

 Maximum 12 trunk groups, up to 16 ports per trunk group

 Up to 16Gbps bandwidth(Duplex Mode)

■ Provide Port Mirror (many-to-1)

■ Port Mirroring to monitor the incoming or outgoing traffic on a particular port

 Quality of Service

■ Ingress Shaper and Egress Rate Limit per port bandwidth control

■ 4 priority queues on all switch ports

■ Traffic classification:

- IEEE 802.1p CoS

- TOS / DSCP / IP Precedence of IPv4/IPv6 packets

- IP TCP/UDP port number

- Typical network application

■ Strict priority and Weighted Round Robin (WRR) CoS policies

■ Supports QoS and In/Out bandwidth control on each port

■ Traffic-policing policies on the switch port

■ QoS Control List Wizard makes QoS creation and configuration easier and more quickly

■ DSCP remarking

 Multicast

■ Supports IGMP Snooping v1, v2 and v3

■ Querier mode support

■ IGMP Snooping port filtering

■ Multicast VLAN Registration (MVR) support

 Security

■ IEEE 802.1x Port-Based / MAC-Based network access authentication

■ Built-in RADIUS client to co-operate with the RADIUS servers

■ TACACS+ login users access authentication

■ RADIUS / TACACS+ users access authentication

■ IP-Based Access Control List (ACL)

■ MAC-Based Access Control List

■ Source MAC / IP address binding

■ DHCP Snooping to filter un-trusted DHCP messages

■ Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding

■ IP Source Guard prevents IP spoofing attacks

■ Auto DoS rule to defend DoS attack

■ IP address access management to prevent unauthorized intruder

4

 Management

■ Switch Management Interfaces

- Console / Telnet Command Line Interface

- Web switch management

- SNMP v1, v2c, and v3 switch management

- SSH / SSL secure access

■ Four RMON groups (history, statistics, alarms, and events)

■ IPv6 IP Address / NTP / DNS management

■ Built-in Trivial File Transfer Protocol (TFTP) client

■ BOOTP and DHCP for IP address assignment

■ Firmware upload/download via HTTP / TFTP

■ DHCP Relay

■ User Privilege levels control

■ NTP (Network Time Protocol)

■ Link Layer Discovery Protocol (LLDP) Protocol

User’s Manual of SGSW-24040 / 24240 Series

■ Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues

■ Reset button for system reboot or reset to factory default

■ PLANET Smart Discovery Utility for deploy management

■ ICMPv6

 Stacking

■ Hardware stack up to 16 units and 384 ports

■ Stacking architecture supports Chain and Ring mode

■ Mirror across stack

■ Link Aggregation groups spanning multiple switches in a stack

■ Hardware learning with MAC table synchronization across stack

 Redundant Power System (SGSW-24040R / 24240R)

■ 100~240V AC / 48V DC Dual power redundant

■ Active-active redundant power failure protection

■ Backup of catastrophic power failure on one supply

■ Fault tolerance and resilience.

5

 Power over Ethernet (SGSW-24040P / 24040P4 / 24040HP Only)

■ Complies with IEEE 802.3af Power over Ethernet End-Span PSE

■ Complies with IEEE 802.3at high-power Power over Ethernet End-Span PSE (SGSW-24040HP only)

■ Up to 24 ports for IEEE 802.3af devices powered

■ Up to 24 ports for IEEE 802.3at devices powered (SGSW-24040HP only)

■ Support PoE Power up to 15.4 watts for each PoE ports

■ Support PoE Power up to 30.8 watts for each PoE ports (SGSW-24040HP only)

■ Auto detect powered device (PD)

■ Circuit protection prevent power interference between ports

■ Remote power feeding up to 100m

■ PoE Management

■ Total PoE power budget control

■ Pert port PoE function enable/disable

■ PoE Port Power feeding priority

■ Per PoE port power limit

■ PD classification detection

1.5 Product Specification

 SGSW Stackable Copper models

Product SGSW-24040 SGSW-24040R

Hardware Specification

Copper Ports
SFP/mini-GBIC Slots
Console Port
Stacking Ports
Switch Fabric
Address Table
Share data Buffer
Switch Processing Scheme

Flow Control

24 10/ 100/1000Base-T RJ-45 Auto-MDI/MDI-X ports

4 SFP interfaces, shared with Port-21 to Port-24

1 x RS-232 DB9 serial port (115200, 8, N, 1)

2 5GbE / Cross-HDMI interface

68Gbps / non-blocking

8K entries, automatic source address learning and ageing

1392 kilobytes

Store-and-Forward

IEEE 802.3x Pause Frame for Full-Duplex

Back pressure for Half-Duplex

Jumbo Frame

Reset Button

Dimension (W x D x H)
Weight

10Kbytes

< 5 seconds: System reboot

> 10 seconds: Factory Default

440 x 200 x 44.5 mm, 1U high

SGSW-24040: 3.0kg

User’s Manual of SGSW-24040 / 24240 Series

SGSW-24040R: 3.1kg

LED
Power Consumption
Power Requirement – AC

Power Requirement – DC

Stacking Numbers
Stacking Bandwidth
Stack ID Display
ESD Protection

Layer 2 Function

Basic Management Interfaces
Secure Management Interface

Port configuration

Power, Link/Act and speed per Gigabit port

Max. 30.2 watts / 102.98 BTU

AC 100~240V, 50/60Hz AC 100~240V, 50/60Hz

-48V DC @ 0.6A

---

Range: -30 ~ -60V

16

10Gbps Full-Duplex

7-Segment LED Display (1~9, A~F,0)

6KV DC

Console, Telnet, Web Browser, SNMPv1, v2c and v3

SSH, SSL, SNMP v3

Port disable/enable.

Auto-negotiation 10/100/1000Mbps full and half duplex mode selection.

Flow Control disable / enable.

Port Status

VLAN

Port trunking

QoS

IGMP Snooping

Bandwidth control on each port.

Power saving mode control

Display each port’s speed duplex mode, link status, Flow control status.

Auto negotiation status, trunk status.

802.1Q Tagged Based VLAN ,up to 255 VLAN groups

Q-in-Q

Private VLAN

Voice VLAN

IEEE 802.3ad LACP / Static Trunk

Support 12 groups of 16-Port trunk support

Traffic classification based, Strict priority and WRR

4-level priority for switching

- Port Number

- 802.1p priority

- DS/TOS field in IP Packet

IGMP (v1/v2) Snooping, up to 255 multicast Groups

IGMP Querier mode support

Access Control List

SNMP MIBs

IP-Based ACL / MAC-Based ACL

Up to 256 entries

RFC-1213 MIB-II

IF-MIB

7

Standards Conformance

User’s Manual of SGSW-24040 / 24240 Series

RFC-1493 Bridge MIB

RFC-1643 Ethernet MIB

RFC-2863 Interface MIB

RFC-2665 Ether-Like MIB

RFC-2737 Entity MIB

RFC-2618 RADIUS Client MIB

RFC-2933 IGMP-STD-MIB

RFC3411 SNMP-Frameworks-MIB

IEEE 802.1X PAE

LLDP

MAU-MIB

Regulation Compliance

Standards Compliance

FCC Part 15 Class A, CE

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX/100Base-FX

IEEE 802.3z Gigabit SX/LX

IEEE 802.3ab Gigabit 1000T

IEEE 802.3x Flow Control and Back pressure

IEEE 802.3ad Port trunk with LACP

IEEE 802.1D Spanning Tree protocol

IEEE 802.1w Rapid Spanning Tree protocol

IEEE 802.1s Multiple Spanning Tree

IEEE 802.1p Class of service

IEEE 802.1Q VLAN Tagging

IEEE 802.1x Port Authentication Network Control

IEEE 802.1ab Link Layer Discovery Protocol (LLDP)

 SGSW Stackable Fiber models

Product SGSW-24240 SGSW-24240R

Hardware Specification

Copper Ports
SFP/mini-GBIC Slots
Console Port
Stacking Ports
Switch Fabric
Address Table

8 10/ 100/1000Base-T RJ-45 Auto-MDI/MDI-X ports, shared with Port-1~Port-8

24 100/1000Base-X Dual Speed SFP interfaces

1 x RS-232 DB9 serial port (115200, 8, N, 1)

2 5GbE / Cross-HDMI interface

68Gbps / non-blocking

8K entries, automatic source address learning and ageing

8

User’s Manual of SGSW-24040 / 24240 Series

Share data Buffer
Switch Processing Scheme

Flow Control

Jumbo Frame

Reset Button

Dimension (W x D x H)

Weight

LED
Power Consumption
Power Requirement – AC

Power Requirement – DC

1392 kilobytes

Store-and-Forward

IEEE 802.3x Pause Frame for Full-Duplex

Back pressure for Half-Duplex

10Kbytes

< 5 seconds: System reboot

> 10 seconds: Factory Default

440 x 200 x 44.5 mm, 1U high

SGSW-24040: 3.0kg

SGSW-24040R: 3.1kg

Power, Link/Act and speed per Gigabit port

Max. 30.2 watts / 102.98 BTU

AC 100~240V, 50/60Hz AC 100~240V, 50/60Hz

-48V DC @ 0.6A

--­Range: -30 ~ -60V

Stacking Numbers
Stacking Bandwidth
Stack ID Display
ESD Protection

Layer 2 Function

Basic Management Interfaces
Secure Management Interface

Port configuration

Port Status

16

10Gbps Full-Duplex

7-Segment LED Display (1~9, A~F,0)

6KV DC

Console, Telnet, Web Browser, SNMPv1, v2c and v3

SSH, SSL, SNMP v3

Port disable/enable.

Auto-negotiation 10/100/1000Mbps full and half duplex mode selection.

Flow Control disable / enable.

Bandwidth control on each port.

Power saving mode control

Display each port’s speed duplex mode, link status, Flow control status.

Auto negotiation status, trunk status.

802.1Q Tagged Based VLAN ,up to 255 VLAN groups

VLAN

Port trunking

QoS

Q-in-Q

Private VLAN

Voice VLAN

IEEE 802.3ad LACP / Static Trunk

Support 12 groups of 16-Port trunk support

Traffic classification based, Strict priority and WRR

4-level priority for switching

9

User’s Manual of SGSW-24040 / 24240 Series

- Port Number

- 802.1p priority

IGMP Snooping

Access Control List

SNMP MIBs

- DS/TOS field in IP Packet

IGMP (v1/v2) Snooping, up to 255 multicast Groups

IGMP Querier mode support

IP-Based ACL / MAC-Based ACL

Up to 256 entries

RFC-1213 MIB-II

IF-MIB

RFC-1493 Bridge MIB

RFC-1643 Ethernet MIB

RFC-2863 Interface MIB

RFC-2665 Ether-Like MIB

RFC-2737 Entity MIB

RFC-2618 RADIUS Client MIB

RFC-2933 IGMP-STD-MIB

RFC3411 SNMP-Frameworks-MIB

IEEE 802.1X PAE

Standards Conformance

Regulation Compliance

Standards Compliance

LLDP

MAU-MIB

FCC Part 15 Class A, CE

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX/100Base-FX

IEEE 802.3z Gigabit SX/LX

IEEE 802.3ab Gigabit 1000T

IEEE 802.3x Flow Control and Back pressure

IEEE 802.3ad Port trunk with LACP

IEEE 802.1D Spanning Tree protocol

IEEE 802.1w Rapid Spanning Tree protocol

IEEE 802.1s Multiple Spanning Tree

IEEE 802.1p Class of service

IEEE 802.1Q VLAN Tagging

IEEE 802.1x Port Authentication Network Control

IEEE 802.1ab Link Layer Discovery Protocol (LLDP)

10

 SGSW Stackable PoE models

Product SGSW-24040P SGSW-24040P4 SGSW-24040HP

Hardware Specification

Copper Ports
SFP/mini-GBIC Slots
Console Port
Stacking Ports
Switch Fabric
Address Table
Share data Buffer
Switch Processing Scheme

Flow Control

Jumbo Frame

Reset Button

Dimension (W x D x H)
Weight

24 10/ 100/1000Base-T RJ-45 Auto-MDI/MDI-X ports

4 SFP interfaces, shared with Port-21 to Port-24

1 x RS-232 DB9 serial port (115200, 8, N, 1)

2 5GbE / Cross-HDMI interface

68Gbps / non-blocking

8K entries, automatic source address learning and ageing

1392 kilobytes

Store-and-Forward

IEEE 802.3x Pause Frame for Full-Duplex

Back pressure for Half-Duplex

10Kbytes

< 5 seconds: System reboot

> 10 seconds: Factory Default

440 x 300 x 44.5 mm, 1U high

4.5kg

LED

Power Consumption

Power Requirement – AC
Stacking Numbers
Stacking Bandwidth
Stack ID Display
ESD Protection

Power over Ethernet

PoE Standard
PoE Power Supply Type

PoE Power Output

Power Pin Assignment
PoE Power Budget

Power, Link/Act and speed per Gigabit port

Max. 290 watts /

989 BTU

AC 100~240V, 50/60Hz AC 100~240V, 50/60Hz AC 100~240V, 50/60Hz

16

10Gbps Full-Duplex

7-Segment LED Display (1~9, A~F,0)

6KV DC

IEEE 802.3af PoE / PSE IEEE 802.3af/at PoE / PSE

End-Span

Per Port 48V DC.

Max. 15.4 watts

1/2(+), 3/6(-)

220 Watts 380 Watts 360 Watts

Max. 430.2 watts /

1467 BTU

Max. 432 watts /

1473 BTU

Per Port 52V DC.

Max. 30.8 watts

PoE Ability

Number of PD @

24 24 24

7Watts

User’s Manual of SGSW-24040 / 24240 Series

Number of PD @

15.4Watts
Number of PD @

30.8Watts

Layer 2 Function

Basic Management Interfaces
Secure Management Interface

Port configuration

Port Status

VLAN

14 24 23

- - 11

Console, Telnet, Web Browser, SNMPv1, v2c and v3

SSH, SSL, SNMP v3

Port disable/enable.

Auto-negotiation 10/100/1000Mbps full and half duplex mode selection.

Flow Control disable / enable.

Bandwidth control on each port.

Power saving mode control

Display each port’s speed duplex mode, link status, Flow control status.

Auto negotiation status, trunk status.

802.1Q Tagged Based VLAN ,up to 255 VLAN groups

Q-in-Q

Private VLAN

Port trunking

QoS

IGMP Snooping

Access Control List

Voice VLAN

IEEE 802.3ad LACP / Static Trunk

Support 12 groups of 16-Port trunk support

Traffic classification based, Strict priority and WRR

4-level priority for switching

- Port Number

- 802.1p priority

- DS/TOS field in IP Packet

IGMP (v1/v2) Snooping, up to 255 multicast Groups

IGMP Querier mode support

IP-Based ACL / MAC-Based ACL

Up to 256 entries

RFC-1213 MIB-II

IF-MIB

RFC-1493 Bridge MIB

RFC-1643 Ethernet MIB

SNMP MIBs

RFC-2863 Interface MIB

RFC-2665 Ether-Like MIB

RFC-2737 Entity MIB

RFC-2618 RADIUS Client MIB

RFC-2933 IGMP-STD-MIB

12

Standards Conformance

User’s Manual of SGSW-24040 / 24240 Series

RFC3411 SNMP-Frameworks-MIB

IEEE 802.1X PAE

LLDP

MAU-MIB

Regulation Compliance

Standards Compliance

FCC Part 15 Class A, CE

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX/100Base-FX

IEEE 802.3z Gigabit SX/LX

IEEE 802.3ab Gigabit 1000T

IEEE 802.3x Flow Control and Back pressure

IEEE 802.3ad Port trunk with LACP

IEEE 802.1d Spanning tree protocol

IEEE 802.1w Rapid spanning tree protocol

IEEE 802.1s Multiple spanning tree protocol

IEEE 802.1p Class of service

IEEE 802.1Q VLAN Tagging

IEEE 802.1x Port Authentication Network Control

IEEE 802.1ab LLDP

RFC 768 UDP

RFC 793 TFTP

RFC 791 IP

RFC 792 ICMP

RFC 2068 HTTP

RFC 1112 IGMP version 1

RFC 2236 IGMP version 2

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet (Pre-Standard)

Note: The PoE networks of this equipment is to be connected without routing to the outside plant.

13

User’s Manual of SGSW-24040 / 24240 Series

2. INSTALLATION

This section describes the hardware features and installation of the Managed Switch on the desktop or rack mount. For easier

management and control of the Managed Switch, familiarize yourself with its display indicators, and ports. Front panel

illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Managed Switch, please

read this chapter completely.

2.1 Hardware Description

2.1.1 Switch Front Panel

The unit front panel provides a simple interface monitoring the switch. Figure 2-1 to 2-4 show the front panel of the Managed

Switches.

SGSW-24040 / SGSW-24040R Front Panel

Figure 2-1 SGSW-24040 / SGSW-24040R front panel.

SGSW-24040P / SGSW-24040P4 Front Panel

Figure 2-2 SGSW-24040P / SGSW-24040P4 front panel.

SGSW-24240 / SGSW-24240R Front Panel

Figure 2-3 SGSW-24240 / SGSW-24240R front panel.

SGSW-24040HP Front Panel

Figure 2-4 SGSW-24040HP front panel.

14

User’s Manual of SGSW-24040 / 24240 Series

■ Gigabit TP interface

10/100/1000Base-T Copper, RJ-45 Twist-Pair: Up to 100 meters.

■ Gigabit SFP slots

1000Base-SX/LX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver module: From 550 meters (Multi-mode fiber),

up to 10/30/50/70/120 kilometers (Single-mode fiber).

■ Console Port

The console port is a DB9, RS-232 male serial port connector. It is an interface for connecting a terminal directly. Through

the console port, it provides rich diagnostic information includes IP Address setting, factory reset, port management, link

status and system setting. Users can use the attached RS-232 cable in the package and connect to the console port on the

device. After the connection, users an run any terminal emulation program (Hyper Terminal, ProComm Plus, Telix, Winterm

and so on) to enter the startup screen of the device.

■ Reset button

At the left of front panel, the reset button is designed for reboot the Managed Switch without turn off and on the power. The

following is the summary table of Reset button functions:

Reset Button Pressed and Released Function

< 5 sec: System reboot Reboot the Managed Switch

Reset the Managed Switch to Factory Default configuration.

The Managed Switch will then reboot and load the default

settings as below:

> 5 sec: Factory Default

■ Stack ID

Each SGSW Managed Stackable Switch on a stack must have a unique “Stack ID”. There are 16 degrees (0~9, A~F) in the

rotary switch. The Stack ID is configured via Web or CLI management interface. Use the Stack ID to identify the location of

the real device.

。 Default Username: admin
。 Default Password: admin
。 Default IP address: 192.168.0.100
。 Subnet mask: 255.255.255.0
。 Default Gateway: 192.168.0.254

Stack ID is not equals to the Master Priority that configured in the management interface.

■ Master LED

If master switch is fail or disconnected to the switch by stack port, the switch with least switch ID will become master.

15

User’s Manual of SGSW-24040 / 24240 Series

2.1.2 LED Indications

The front panel LEDs indicates instant status of port links, data activity and system power; helps monitor and troubleshoot when

needed. Figure 2-5 & Figure 2-7 shows the LED indications of these Managed Switches.

SGSW-24040 / SGSW-24040R LED indication

Figure 2-5 SGSW-24040 / SGSW-24040R LED panel

■ System

LED Color Function

PWR Green

Master Green

STX1 Green

STX2 Green

■ 10/100/1000Base-T interfaces

LED Color Function

1000

Green

LNK/ACT

Lights to indicate that the Switch is powered on.
Blink to indicate the System is running under booting procedure.

Lights to indicate that the Switch is the Master of the stack group.

Lights to indicate the stacking link through that port is successfully established.

Lights to indicate the stacking link through that port is successfully established.

Lights:

Blink:

Off:

To indicate the link through that port is successfully established with speed

1000Mbps

To indicate that the switch is actively sending or receiving data over that port.

If L10/100 NK/ACT LED light-> indicate that the port is operating at 10Mbps or

10/100

LNK/ACT

Orange

Lights:

Blink:

Off:

100Mbps

If LNK/ACT LED Off -> indicate that the port is link down

To indicate the link through that port is successfully established with speed

10Mbps or 100Mbps

To indicate that the switch is actively sending or receiving data over that port.

If 1000 LNK/ACT LED light-> indicate that the port is operating at 1000Mbps

If 1000 LNK/ACT LED Off -> indicate that the port is link down

16

■ 1000Base-SX/LX SFP interfaces (Shared Port-21~Port-24)

LED Color Function

User’s Manual of SGSW-24040 / 24240 Series

Lights:

1000

Green

LNK

Off:

To indicate the link through that SFP port is successfully established with

speed 1000Mbps

To indicate that the SFP port is link down

SGSW-24040P / SGSW-24040P4 / SGSW-24040HP LED indicati on

Figure 2-6 SGSW-24040P / SGSW-24040P4 LED panel

■ System

LED Color Function

PWR Green

Master Green

STX1 Green

STX2 Green

■ Alert

LED Color Function

PWR Alert Green Lights to indicate that the power supply failure
FAN1 Alert Green Lights to indicate that the FAN1 failure
FAN2 Alert Green Lights to indicate that the FAN2 failure
FAN3 Alert Green Lights to indicate that the FAN3 failure

Lights to indicate that the Switch is powered on.
Blink to indicate the System is running under booting procedure.

Lights to indicate that the Switch is the Master of the stack group

Lights to indicate the stacking link through that port is successfully established.

Lights to indicate the stacking link through that port is successfully established.

17

■ 10/100/1000Base-T interfaces

LED Color Function

User’s Manual of SGSW-24040 / 24240 Series

Lights:

10/100/1000

Green

LNK/ACT

PoE In-Use Orange

■ 1000Base-SX/LX SFP interfaces (Shared Port-21~Port-24)

LED Color Function

1000

Green

LNK

Blink:

Off:

Lights:

Off:

Lights:

Off:

To indicate the link through that port is successfully established with speed

10Mbps or 100Mbps or 1000Mbps

To indicate that the switch is actively sending or receiving data over that port.

If L10/100 NK/ACT LED light-> indicate that the port is operating at 10Mbps or

100Mbps

If LNK/ACT LED Off -> indicate that the port is link down

To indicate the port is providing 48VDC in-line power

To indicate the connected device is not a PoE Powered Device (PD)

To indicate the link through that SFP port is successfully established with

speed 1000Mbps

To indicate that the SFP port is link down

SGSW-24240 / SGSW-24240R LED indication

Figure 2-7 SGSW-24240 / SGSW-24240R LED panel

■ System

LED Color Function

Lights to indicate that the Switch is powered on.

PWR Green

Blink to indicate the System is running under booting procedure.

Master Green

Lights to indicate that the Switch is the Master of the stack group

18

User’s Manual of SGSW-24040 / 24240 Series

STX1 Green

STX2 Green

■ 10/100/1000Base-T interfaces (Shared Port-1~Port-8)

LED Color Function

1000

Green

LNK/ACT

10/100

Orange

LNK/ACT

Lights to indicate the stacking link through that port is successfully established.

Lights to indicate the stacking link through that port is successfully established.

Lights:

Blink:

Off:

Lights:

Blink:

Off:

To indicate the link through that port is successfully established with speed

1000Mbps

To indicate that the switch is actively sending or receiving data over that port.

If L10/100 NK/ACT LED light-> indicate that the port is operating at 10Mbps or

100Mbps

If LNK/ACT LED Off -> indicate that the port is link down

To indicate the link through that port is successfully established with speed

10Mbps or 100Mbps

To indicate that the switch is actively sending or receiving data over that port.

If 1000 LNK/ACT LED light-> indicate that the port is operating at 1000Mbps

■ 100 / 1000Base-X SFP interfaces

LED Color Function

Lights:

1000

Green

LNK

100

Orange

LNK/ACT

■ 7-Segment LED Display

Off:

Lights:

Blink:

Off:

If 1000 LNK/ACT LED Off -> indicate that the port is link down

To indicate the link through that SFP port is successfully established with

speed 1000Mbps

To indicate that the SFP port is link down

To indicate the link through that port is successfully established with speed

100Mbps

To indicate that the switch is actively sending or receiving data over that port.

If 1000 LNK/ACT LED light-> indicate that the port is operating at 1000Mbps

If 1000 LNK/ACT LED Off -> indicate that the port is link down

Stack ID (1~9, A ~F, 0): To indicate the Switch ID of each SGSW Managed Switch. Switch IDs are used to uniquely identify

the Managed Switches within a stack. The Switch ID of each Managed Switch is shown on the display on the front of the

Managed Switch and is used widely in the web pages as well as in the CLI commands of the Stack group.

Stack ID 1 2 3 4 5 6 7 8 9 A. B. C. D. E. F. 0
Switch ID 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

19

User’s Manual of SGSW-24040 / 24240 Series

2.1.3 Switch Rear Panel

The rear panel of the Managed Switch indicates an AC inlet power socket, which accepts input power from 100 to 240V AC,

50-60Hz. Figure 2-8 & Figure 2-12 shows the rear panel of these Managed Switches

SGSW-24040 Rear Panel

Figure 2-8 Rear panel of SGSW-24040

SGSW-24040R Rear Panel

Figure 2-9 Rear panel of SGSW-24040R

SGSW-24040P / SGSW-24040P4 / SGSW-24040HP Rear Panel

Figure 2-10 Rear panel of SGSW-24040P / SGSW-24040P4 / SGSW-24040HP

SGSW-24240 Rear Panel

Figure 2-11 Rear panel of SGSW-24240

SGSW-24240R Rear Panel

Figure 2-12 Rear panel of SGSW-24240R

■ AC Power Receptacle

For compatibility with electric service in most areas of the world, the Managed Switch’s power supply automatically adjusts

to line power in the range 100-240VAC and 50/60 Hz.

Plug the female end of the power cord firmly into the receptalbe on the rear panel of the Managed Switch. Plug the other

end of the power cord into an electric service outlet then the power will be ready.

20

User’s Manual of SGSW-24040 / 24240 Series

The device is a power-required device, it means, it will not work till it is powered. If your networks should

active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will

Po

wer Notice:

■ DC Power Connector

The rear panel of the SGSW-24040R contains a power switch and a DC power connector, which accepts DC power input

voltage from -30V to -60V DC. Connect the power cable to the Managed Switch at the input terminal block. The size of the

two screws in the terminal block is M3.5.

prevent you from network data loss or network downtime.

In some area, installing a surge suppression device may also help to protect your Managed Switch from

being damaged by unregulated surge or current to the Switch or the power adapter.

Figure 2-13 Rear Panel of SGSW-24040R

Before connect the DC power cable to the input terminal block of SGSW-24040R, ensure that the power

Warning:

■ Stack ports

SGSW-24040 / 24040R Series

There are two High-Performance stack ports on the rear panel. One is STX1 / Cascade Down and the other is STX2 /
Cascade UP.
 When stacked, the STX1 / Cascade Down port should connect to the other switch’s STX2 / Cascade UP port and the

STX2 / Cascade UP port should connect to other switch’s STX1 / Cascade Down out.

 You can just use attached PLANET CB-STX50 or longer stack cable CB-STX200 connector to stack.

 The CB-STX50 and CB-STX200 are Cross-Overed HDMI cables; only attached PLANET stack cable can be used.

 Plug-and-play connection.

switch in the “OFF” position and the DC power is OFF

21

User’s Manual of SGSW-24040 / 24240 Series

Figure 2-14 SGSW-24040 /24040R Series Stack Ports

22

User’s Manual of SGSW-24040 / 24240 Series

2.2 Install the Switch

This section describes how to install your Managed Switch and make connections to the Managed Switch. Please read the

following topics and perform the procedures in the order being presented. To install your Managed Switch on a desktop or shelf,

simply complete the following steps.

2.2.1 Desktop Installation

To install the Managed Switch on desktop or shelf, please follows these steps:

Step1: Attach the rubber feet to the recessed areas on the bottom of the Managed Switch.
Step2: Place the Managed Switch on the desktop or the shelf near an AC power source, as shown in Figure 2-15.

Figure 2-15 Place the Managed Switch on the desktop

Step3: Keep enough ventilation space between the Managed Switch and the surrounding objects.

When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1,

Section 4, and Specification.

Step4: Connect the Managed Switch to network devices.

Connect one end of a standard network cable to the 10/100/1000 RJ-45 ports on the front of the Managed Switch

Connect the other end of the cable to the network devices such as printer servers, workstations or routers…etc.

Connection to the Managed Switch requires UTP Category 5 network cabling with RJ-45 tips. For more

information, please see the Cabling Specification in Appendix A.

23

User’s Manual of SGSW-24040 / 24240 Series

Step5: Supply power to the Managed Switch.

Connect one end of the power cable to the Managed Switch.

Connect the power plug of the power cable to a standard wall outlet.

When the Managed Switch receives power, the Power LED should remain solid Green.

2.2.2 Rack Mounting

To install the Managed Switch in a 19-inch standard rack, please follows the instructions described below.

Step1: Place the Managed Switch on a hard flat surface, with the front panel positioned towards the front side.
Step2: Attach the rack-mount bracket to each side of the Managed Switch with supplied screws attached to the package.

Figure 2-16 shows how to attach brackets to one side of the Managed Switch.

Figure 2-16 Attach brackets to the Managed Switch.

You must use the screws supplied with the mounting brackets. Damage caused to the parts by

using incorrect screws would invalidate the warranty.

Step3: Secure the brackets tightly.
Step4: Follow the same steps to attach the second bracket to the opposite side.
Step5: After the brackets are attached to the Managed Switch, use suitable screws to securely attach the brackets to the rack,

as shown in Figure 2-17.

24

User’s Manual of SGSW-24040 / 24240 Series

Figure 2-17 Mounting SGSW-24040 in a Rack

Step6: Proceeds with the steps 4 and steps 5 of session 2.2.1 Desktop Installation to connect the network cabling and supply

power to the Managed Switch.

2.2.3 Installing the SFP transceiver

The sections describe how to insert an SFP transceiver into an SFP slot.

The SFP transceivers are hot-pluggable and hot-swappable. You can plug-in and out the transceiver to/from any SFP port

without having to power down the Managed Switch. As the Figure 2-18 appears.

Figure 2-18 Plug-in the SFP transceiver

25

User’s Manual of SGSW-24040 / 24240 Series

 Approv

PLANET Managed Switch supports both Single mode and Multi-mode SFP transceiver. The following list of approved PLANET

SFP transceivers is correct at the time of publication:

■ MGB-SX SFP (1000BASE-SX SFP transceiver / Multi-mode / 850nm / 220m~550m)

■ MGB-LX SFP (1000BASE-LX SFP transceiver / Single mode / 1310nm / 10km)

■ MGB-L30 SFP (1000BASE-LX SFP transceiver / Single mode / 1310nm / 30km)

■ MGB-L50 SFP (1000BASE-LX SFP transceiver / Single mode / 1310nm / 50km)

■ MGB-LA10 SFP (1000BASE-LX SFP transceiver / WDM Single mode / TX: 1310nm, RX: 1550nm/ 10km)

■ MGB-LB10 SFP (1000BASE-LX SFP transceiver / WDM Single mode / TX: 1550nm, RX: 1310nm / 10km)

Before connect the other Managed Switches, workstation or Media Converter.

1. Make sure both side of the SFP transceiver are with the same media type, for example: 1000Base-SX to 1000Base-SX,

ed PLANET SFP Transceivers

It recommends using PLANET SFPs on the Managed Switch. If you insert a SFP transceiver that is

not supported, the Managed Switch will not recognize it.

1000Bas-LX to 1000Base-LX.

2. Check the fiber-optic cable type match the SFP transceiver model.

 To connect to 1000Base-SX SFP transceiver, use the Multi-mode fiber cable- with one side must be male duplex LC

connector type.

 To connect to 1000Base-LX SFP transceiver, use the Single-mode fiber cable-with one side must be male duplex LC

connector type.

 Connect the fiber cable

1. Attach the duplex LC connector on the network cable into the SFP transceiver.

2. Connect the other end of the cable to a device – switches with SFP installed, fiber NIC on a workstation or a Media

Converter..

3. Check the LNK/ACT LED of the SFP slot on the front of the Managed Switch. Ensure that the SFP transceiver is operating

correctly.

4. Check the Link mode of the SFP port if the link failed. Co works with some fiber-NICs or Media Converters, set the Link

mode to “1000 Force” is needed.

 Remove the transceiver module

1. Make sure there is no network activity by consult or check with the network administrator. Or through the management

interface of the switch/converter (if available) to disable the port in advance.

2. Remove the Fiber Optic Cable gently.

3. Turn the handle of the MGB module to horizontal.

4. Pull out the module gently through the handle.

26

User’s Manual of SGSW-24040 / 24240 Series

Figure 2-19 Pull out the SFP transceiver

Never pull out the module without pull the handle or the push bolts on the module. Direct pull

out the module with violent could damage the module and SFP module slot of the Managed

Switch.

2.2.4 Connecting DC Power Supply – SGSW-24040R / 24240R

The SGSW-24040R supports -48VDC power input, connect the power cable to the switch at the input terminal block.

1. The size of the two screws in the terminal block is M3.5.

2. The terminals are marked “-48V”, “FG“.

3. Loosen the two screws so you can slide the DC cable beneath it. Insert the DC cable into the connector first, and screw it

down tight.

4. Connect the power cable to the DC power supply. After power up or reset, the Managed Switch performs a cold start

procedure.

Figure 2-20 -48VDC connector

27

User’s Manual of SGSW-24040 / 24240 Series

Warning:

Before connect the DC power cable to the input terminal block of Managed Switch, ensure that the

power switch in the “OFF” position and the DC power is OFF

28

User’s Manual of SGSW-24040 / 24240 Series

2.3 Stack Installation

SGSW-24040 / 24240 Series

The SGSW-24040 / 24240 series Managed Switch provides a switch stacking function to manage up to 16 switches using a

single IP address. And up to 384 Gigabit Ethernet ports can be managed by a stacking group and you can add ports and

functionality as needed. You can add SGSW-24040 / 24240 series switches as needed to support more network clients,

knowing that your switching fabric will scale to meet increasing traffic demands.

Two types of stack topologies are supported by the SGSW-24040 / 24240 series:

 Chain topology (same as a disconnected ring)
 Ring topology

Please find the following picture for sample connection.

Figure 2-21 Chain Stack topology

Figure 2-22 Ring Stack topology

29

User’s Manual of SGSW-24040 / 24240 Series

2.3.1 Connecting Stacking cable

Before attempting to connect stacking ports, verify that you have the required stack cables. The following cables are used to

connect stacked switches:

 CB-STX50: 50cm, Short stack cable –used to connect adjacent SGSW switches.
 CB-STX200: 200cm, Long / Redundant stack cable – used to connect the top and bottom SGSW switches of a stack.

There are two high-performance HDMI-like Stack ports on the rear panel for proprietary management stack. Only attached

PLANET CB-STX50 and CB-STX200 cross-overed HDMI cable can be used.

STEP-1: Plug one end of the cable in the “STX1 / Cascade Down” port and the other end to the ”STX2 / Cascade UP” port of

next device.

STEP-2: Repeat the step for every device in the stack cluster, then ending at last switch.

Figure 2-23 Stacking connection

STEP-3: If you wish to implement stack redundancy, use the long stack cable –CB-STX200 to connect the stack port marked

“STX1 / Cascade Down” on the bottom switch to the port marked “STX2 / Cascade Up” on the top switch of the stack.

The stack port is for management and data packets to be transmitted between other SGSW stackable

switches, the stack ports can’t be configured with Layer 2 features via management interface.

STEP-4: Power up the stack switches.

2.3.2 Management Stacking

The stack operation of the SGSW Managed Switch supports Plug and Play Stacking connection and auto stack configuration.

STEP-5: Once the stack start operation, the Stack master be automatically elected without any configure. The Stack master is

30

User’s Manual of SGSW-24040 / 24240 Series

indicated by a lit green “Master” LED on the front panel. As the Figure 2-24 appears.

Master LED

Figure 2-24 Stack Master with “Master” LED lit

Stack ID

STEP-6: When a SGSW Switch is added to the stack, a Switch ID is automatically assigned to the SGSW Switch. The

automatic SID assignment can be modified by choosing a different Switch ID on the Stack Configuration page. This

method allows Switch IDs to be assigned so that it is easier for the user to remember the ID of each switch.

STEP-7: Connect the RS-232 serial cable to the console port on the front of the stack master, then loin the SGSW Switch to

start the switch management. Or you can use the PLANET Smart Discovery Utility to displayt the IP address of the
stack and Web login the stack with this IP address. The default IP address of the SGSW Switch is 192.168.0.100.

Figure 2-25 Use PLANET Smart Discovery Utility to display the IP address of stack master

31

User’s Manual of SGSW-24040 / 24240 Series

1. The stack switch with least priority ID or MAC Address number will become Master. Only Master

switch’s management interface (console, telnet, web and SNMP) is accessible.

It’s allow to build a stack of up to 16 PLANET SGSW Switches. If there is the space limitation or power issue and you wish to

stack all the switches in different racks, use long stack cables “CB-STX200” to connect two stacks.

2m stack cable CB-STX200 2m stack cable CB-STX200

F

igure 2-26 Separated Stack connection

CB-STX50

32

User’s Manual of SGSW-24040 / 24240 Series

3. SWITCH MANAGEMENT

This chapter explains the methods that you can use to configure management access to the Managed Switch. It describes the

types of management applications and the communication and management protocols that deliver data between your

management device (workstation or personal computer) and the system. It also contains information about port connection

options.

This chapter covers the following topics:

 Requirements

 Management Access Overview

 Administration Console Access

 Web Management Access

 SNMP Access

 Standards, Protocols, and Related Reading

3.1 Requirements

 Workstations of subscribers running Windows 98/ME, NT4.0, 2000/XP, MAC OS9 or later, Linux, UNIX or other

platform compatible with TCP/IP protocols.

 Workstation installed with Ethernet NIC (Network Interface Card)
 Serial Port connect (Terminal)

 Above PC with COM Port (DB9 / RS-232) or USB-to-RS-232 converter

 Ethernet Port connect

 Network cables - Use standard network (UTP) cables with RJ45 connectors.

 Above Workstation installed with WEB Browser and JAVA runtime environment Plug-in

It is recommended to use Internet Explore 7.0 or above to access Managed Switch.

33

User’s Manual of SGSW-24040 / 24240 Series

3.2 Management Access Overview

The Managed Switch gives you the flexibility to access and manage it using any or all of the following methods:

 An administration console
 Web browser interface
 An external SNMP-based network management application

The administration console and Web browser interface support are embedded in the Managed Switch software and are

available for immediate use. Each of these management methods has their own advantages. Table 3-1 compares the three

management methods.

Method Advantages Disadvantages

Console

Web Browser

SNMP Agent

 No IP address or subnet needed

 Text-based

 Telnet functionality and HyperTerminal

built into Windows

95/98/NT/2000/ME/XP operating

systems

 Secure

 Ideal for configuring the switch remotely

 Compatible with all popular browsers

 Can be accessed from any location

 Most visually appealing

 Communicates with switch functions at

the MIB level

 Based on open standards

 Must be near switch or use dial-up connection

 Not convenient for remote users

 Modem connection may prove to be unreliable

or slow

 Security can be compromised (hackers need

only know the IP address and subnet mask)

 May encounter lag times on poor connections

 Requires SNMP manager software

 Least visually appealing of all three methods

 Some settings require calculations

 Security can be compromised (hackers need

only know the community name)

Table 3-1 Management Methods Comparison

3.3 Administration Console

The administration console is an internal, character-oriented, and command line user interface for performing system

administration such as displaying statistics or changing option settings. Using this method, you can view the administration

console from a terminal, personal computer, Apple Macintosh, or workstation connected to the switch's console (serial) port.

There are two ways to use this management method: via direct access or modem port access. The following sections describe

these methods. For more information about using the console, refer to Chapter 5 Command Line Interface Console
Management.

34

User’s Manual of SGSW-24040 / 24240 Series

Figure 3-1 Console management

Direct Access

Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a

terminal-emulation program (such as HyperTerminal) to the Managed Switch console (serial) port.
When using this management method, a straight DB9 RS-232 cable is required to connect the switch to the PC. After

making this connection, configure the terminal-emulation program to use the following parameters:

The default parameters are:

 115200 bps
 8 data bits
 No parity
 1 stop bit

Figure 3-2 Terminal parameter settings

You can change these settings, if desired, after you log on. This management method is often preferred because you can

remain connected and monitor the system during system reboots. Also, certain error messages are sent to the serial port,

regardless of the interface through which the associated action was initiated. A Macintosh or PC attachment can use any

terminal-emulation program for connecting to the terminal serial port. A workstation attachment under UNIX can use an emulator

such as TIP.

35

User’s Manual of SGSW-24040 / 24240 Series

3.4 Web Management

The Managed Switch offers management features that allow users to manage the Managed Switch from anywhere on the

network through a standard browser such as Microsoft Internet Explorer. After you set up your IP address for the switch, you can

access the Managed Switch's Web interface applications directly in your Web browser by entering the IP address of the

Managed Switch.

Figure 3-3 Web management

You can then use your Web browser to list and manage the Managed Switch configuration parameters from one central location,

just as if you were directly connected to the Managed Switch's console port. Web Management requires either Microsoft

Internet Explorer 6.0 or later, Safari or Mozilla Firefox 1.5 or later.

Figure 3-4 Web main screen of Managed Switch

36

User’s Manual of SGSW-24040 / 24240 Series

37

User’s Manual of SGSW-24040 / 24240 Series

3.5 SNMP-Based Network Management

You can use an external SNMP-based application to configure and manage the Managed Switch, such as SNMPc Network

Manager, HP Openview Network Node Management (NNM) or What’s Up Gold. This management method requires the SNMP

agent on the switch and the SNMP Network Management Station to use the same community string. This management
method, in fact, uses two community strings: the get community string and the set community string. If the SNMP Net-work

management Station only knows the set community string, it can read and write to the MIBs. However, if it only knows the get

community string, it can only read MIBs. The default gets and sets community strings for the Managed Switch are public.

Figure 3-5 SNMP management

38

User’s Manual of SGSW-24040 / 24240 Series

4. WEB CONFIGURATION

This section introduces the configuration and functions of the Web-Based management.

About Web-based Management

The Managed Switch offers management features that allow users to manage the Managed Switch from anywhere on the

network through a standard browser such as Microsoft Internet Explorer.

The Web-Based Management supports Internet Explorer 7.0. It is based on Java Applets with an aim to reduce network

bandwidth consumption, enhance access speed and present an easy viewing screen.

By default, IE7.0 or later version does not allow Java Applets to open sockets. The user has to

explicitly modify the browser setting to enable Java Applets to use network ports.

The Managed Switch can be configured through an Ethernet connection, make sure the manager PC must be set on same the

IP subnet address with the Managed Switch.

For example, the default IP address of the SGSW Managed Switch is 192.168.0.100, then the manager PC should be set at

192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.

If you have changed the default IP address of the Managed Switch to 192.168.1.1 with subnet mask 255.255.255.0 via console,

then the manager PC should be set at 192.168.1.x (where x is a number between 2 and 254) to do the relative configuration on

manager PC.

Figure 4-1-1 Web Management

39

User’s Manual of SGSW-24040 / 24240 Series

 Logging on the switch

1. Use Internet Explorer 7.0 or above Web browser. Enter the factory-default IP address to access the Web interface. The

factory-default IP Address as following:

http://192.168.0.100

2. When the following login screen appears, please enter the default username "admin" with password “admin” (or the

username/password you have changed via console) to login the main screen of Managed Switch. The login screen in

Figure 4-1-2 appears.

Figure 4-1-2 Login screen

Default User name: admin
Default Password: admin

After entering the username and password, the main screen appears as Figure 4-1-3.

40

User’s Manual of SGSW-24040 / 24240 Series

Figure 4-1-3 Default main page

Now, you can use the Web management interface to continue the switch management or manage the Managed Switch by Web

interface. The Switch Menu on the left of the web page let you access all the commands and statistics the Managed Switch

provides.

1. It is recommended to use Internet Explore 7.0 or above to access Managed Switch.

2. The changed IP address take effect immediately after click on the Save button, you need to

use the new IP address to access the Web interface.

3. For security reason, please change and memorize the new password after this first setup.

4. Only accept command in lowercase letter under web interface.

41

User’s Manual of SGSW-24040 / 24240 Series

4.1 Main Web Page

The SGSW Managed Switch provides a Web-based browser interface for configuring and managing it. This interface allows you

to access the Managed Switch using the Web browser of your choice. This chapter describes how to use the Managed Switch’s

Web browser interface to configure and manage it.

Main Functions Menu

Copper Port Link Status

SFP Port Link Status

Stack Port Link Status

Main Screen

igure 4-1-4 Main Page

F

Panel Display

The web agent displays an image of the Managed Switch’s ports. The Mode can be set to display different information for the

ports, including Link up or Link down. Clicking on the image of a port opens the Port Statistics page.

The port states are illustrated as follows:

Help Button

State Disabled Down Link

RJ-45 Ports

SFP Ports

Stack Ports

Main Menu

Using the onboard web agent, you can define system parameters, manage and control the Managed Switch, and all its ports, or

monitor network conditions. Via the Web-Management, the administrator can setup the Managed Switch by select the functions

those listed in the Main Function. The screen in Figure 4-1-5 appears.

42