Planet POE-E304 User Manual

1. Package Contents

Thank you for purchasing PLANET 1-port IEEE 802.3bt PoE++ to 4-port IEEE 802.3af/at Gigabit PoE Extender, POE-E304. “Gigabit PoE Extender” mentioned in this manual refers to the POE-E304.

Open the box of the Gigabit PoE Extender and carefully unpack it. The box should contain the following items:

Gigabit PoE Extender x 1

User’s Manual x 1 Rubber Feet x 4

 Automatic address learning and address aging

 Case and Installation

 No external power cable installation required

 Made of metal, desktop size design

 Wall-mountable, Plug-and-Play installation

 0 ~ 50 degrees C operating Temperature

PSE (power sourcing equipment) is a device (switch or hub for instance) that will provide power in a PoE setup. The maximum allowed continuous output power per such device in IEEE 802.3af is 15.4 watts and in IEEE 802.3at is 30 watts.

Note

PD (powered device) such as IP phone, network camera or wireless access point is a PoE-enabled terminal that consumes energy supplied by PSE.

Power

PoE In: IEEE 802.3bt or 4-pair 802.3at PoE+

Requirements

External DC: 50~56V DC

Power Consumption

0.9 watts/3.1BTU (System on) 74 watts/252.4BTU (Full loading with PoE function)

10BASE-T: 4-pair UTP Cat5 up to 100m (328ft)

Network Cable

100BASE-TX: 4-pair UTP Cat5 up to 100m (328ft) 1000BASE-T: 4-pair UTP Cat5e, 6, up to 100m (328ft) EIA/TIA-568 100-ohm STP (100m, 328ft)

Power over Ethernet

PoE In Port

PoE Standard

Per PoE Out Port

compliant with voltage within 50-56V DC

IEEE 802.3bt Power over Ethernet Plus Plus endspan and mid-span PD class 4 PD

IEEE 802.3at Power over Ethernet Plus end-span PSE IEEE 802.3af Power over Ethernet end-span PSE

4. Hardware Introduction

4.1 Three-View Diagram

The three-view diagram of the Gigabit PoE Extender consists of one auto-sensing 10/100/1000BASE-T 802.3bt PoE In port, and four autosensing 10/100/1000BASE-T 802.3af/802.3at PoE Out ports. The LED Indicators are also located on the port of Gigabit PoE Extender front panel.

50-56V

168

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

- 1 -

2. Product Features

 Physical Port

 5 10/100/1000BASE-T Gigabit RJ45 interfaces

- 1-port data + power input

- 4-port data + power output

 Power over Ethernet

 1-port data + power input

- Complies with IEEE 802.3bt PoE++ PD

- Supports PoE input power up to 95 watts

 4-port data + power output

- Complies with IEEE 802.3af/IEEE 802.3at PoE+/end-span PSE

- Up to 4 IEEE 802.3af/802.3at devices powered

- Supports PoE power up to 32 watts for each PoE port

- Auto detects powered device (PD)

 Extends the range of PoE to an additional 100 meters (328ft.)

 Forwards both Ethernet data and PoE power to remote device

 Layer 2 Features

 Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/

MDI-X

 Integrates address look-up engine, supporting 2K absolute MAC

addresses

 9K jumbo packet support

 Features Store-and-Forward mode with wire-speed ltering and

forwarding rates

 IEEE 802.3x ow control for full duplex operation and backpressure

for half duplex operation

3.ProductSpecications

Model POE-E304

Hardware Specications

PoE In Port

1 x 10/100/1000BASE-T Ethernet with IEEE 802.3bt PoE++ “Data + DC” in, auto MDI/MDI-X, auto-

Network Connector

Data Rate 10/100/1000Mbps

Switch Architecture

MAC Address Table

Data Buer 1Mbits

Switch Fabric 10Gbps

Switch Throughput

Jumbo Frame 9K

Flow Control

LED Indicators

Protection

Enclosure Metal

Installation Desktop/Wall mountable

Dimensions (W x D x H)

Weight 403g

negotiation RJ45 connector

PoE Out Port

4 x 10/100/1000BASE-T Ethernet with IEEE

802.3af/802.3at PoE “Data + DC” out, auto MDI/ MDI-X, auto-negotiation RJ45 connector

- 3 -

Store-and-Forward

7.44Mpps @ 64 bytes

IEEE 802.3x pause frame for full duplex Back pressure for half duplex

PoE In Port 10/100/1000 LNK/ACT (green) PoE Out Port 1 to Port 4 10/100/1000 LNK/ACT (green) PoE-in-Use (orange) PWR (orange)

ESD: Contact 4KV, Air 6KV

Surge: 4KV

168 x 93 x 32mm

PoE In Port

PoE Power

50~56V DC, max. 95 watts input

Per PoE Out Port

50~55V DC, max. 32 watts output

PoE In Port

Power Pin Assignment

1/2 (-), 3/6 (+); 4/5 (+), 7/8 (-)

Per PoE Out Port

1/2 (-), 3/6 (+), end-span (Type A)

PoE Power Budget

65 watts (max.) @ IEEE 802.3bt PoE++ Type 4 PSE input 32 watts (max.) @ IEEE 802.3at PoE+ PSE input

Standard Conformance

Regulatory Compliance

FCC Part 15 Class A, CE

IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet

Standard Compliance

IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus IEEE 802.3bt Power over Ethernet Plus Plus IEEE 802.3x Flow Control

Environment

Operating

Storage

Temperature: 0 ~ 50 degrees C Relative Humidity: 5 ~ 95% (non-condensing)

Temperature: -10 ~ 70 degrees C Relative Humidity: 5 ~ 95% (non-condensing)

The maximum distance that data and power can transmit

Note

depends on the quality of the UTP cable and environment.

- 5 -

PoE-in-Use

10/100/1000

POE-E304

LNK ACT

PoE Out

122

- 7 -

4.2 Ports Connection

Connect the PoE IN port from the following 802.3bt PoE++ PSE devices through a Cat5/5e/6 UTP cable:

PoE IN Port

 802.3bt PoE++/UPOE/PoH injector  802.3bt PoE++/UPOE/PoH injector hub  802.3bt PoE++/UPOE/PoH Ethernet switch

Connect the PoE OUT port to the following 802.3at/af PD devices through a Cat5/5e/6 UTP cable:

PoE OUT Port

 PoE IP camera  PoE VoIP phone  PoE wireless AP  PoE splitter

4.3 LED Indicators

 802.3bt PoE IN Port

LED Color Function

Lights to indicate the link through that

10/100/1000 LNK/ACT

Green

port is successfully established at 10/100/1000Mbps.

Blinks to indicate that the port is actively

sending or receiving data.

5PWR41 2

PoE In

- 2 -

- 4 -

- 6 -

- 8 -

 802.3af/at PoE Out Ports

PoE In

PoE Out

LED Color Function

Lights to indicate the link through that

10/100/1000

LNK/ACT

Green

port is successfully established at 10/100/1000Mbps.

Blinks to indicate that the port is actively

sending or receiving data.

PoE-in-Use Orange

Lights to to indicate the port is providing

55V DC in-line power output.

 Power

LED Color Function

PWR Orange Lights to indicate the device is powered on.

5.3 Connecting POE-E304 to PD

Step 1: Connect the additional Cat5e/6 cable that will be used to

connect to the remote PD to the “PoE Out” port of the Gigabit PoE Extender.

UTP

PoE

5PWR41 2

PoE In

IEEE 802.3bt PoE Switch

PoE Wireless AP

PoE Camera

UTP

PoE

PoE-in-Use

10/100/1000 LNK ACT

POE-E304

PoE Out

UTP

PoE

5. Hardware Installation

5.1 Before Installation

The POE-E304 is installed between the PSE and the PD; it is powered by PSE and forwards the Ethernet data and remaining PoE power or an external power supply to the PD. It can be installed easily by just Plug

and Play without aecting the data transmission performance.

1. To provide you with better PoE power and data extension quality, we strongly recommend that you use “Solid UTP Cable” when installing the POE-E304.

Note

5.2 Connecting POE-E304 to PSE

This section describes how to install Gigabit PoE Extender and make connection to it. Please read the following descriptions and perform the procedures in the order being presented.

There are 5 RJ45 ports in the Gigabit PoE Extender, of which the “PoE

IN” port functions as "PoE (Data and Power) input" and the four ”PoE Out” ports function as "PoE (Data and Power) output".

Step 1: Connect a standard Cat5e/6 UTP cable from PSE, such as

Step 2: The PSE delivers both Ethernet data and PoE power over UTP

Note

Caution

2. The POE-E304 can be installed with a third-party device if the device complies with IEEE 802.3af/at standard.

- 9 -

PoE++ switch, PoE++ injector hub and single port PoE++ injector, to the “PoE IN” port of the Gigabit PoE Extender.

UTP

PoE

5PWR41 2

POE-E304

PoE-in-Use

10/100/1000 LNK ACT

cable to the Gigabit PoE Extender.

1. When the PoE-in-Use LED turns steady orange, it means the Gigabit PoE OUT is supplying power successfully from PSE.

2. If the PoE-in-use LED is not lit, please check the remote PSE or the cable connecting to a PC or a network device to see if the cable is correct.

Never connect any non-standard PoE PSE to the Gigabit PoE Extender or else it will damage the device permanently.

IEEE 802.3bt PoE Switch

Step 2: The "PoE Out" port is also the power injector which transmits

DC voltage to the Cat5e/6 cable and transfer data and power simultaneously between the PSE and PD.

Step 3: Once the Gigabit PoE Extender detects the existence of an

IEEE 802.3af/at device, the “PoE-in-Use” LED indicator will be lit steadily, showing it is providing power.

1. If the connected device is not fully complying with IEEE

802.3af/at standard or in-line power device, the PoE-inUse LED indicator of the Gigabit PoE Extender will not be lit steadily.

Note

2. According to IEEE 802.3af/at standard, the Gigabit PoE Extender will not inject power to the cable if not connected to a standard IEEE 802.3af/at device.

- 11 -

5.4 PoE Power Distribution

The POE-E304 can obtain a maximum of 95-watt PoE power from IEEE 802.3bt PoE++ input port and supplies a maximum of 65-watt PoE power budget to four PoE output ports, extending both the reach of Gigabit Ethernet Data and IEEE 802.3af/802.3at PoE over the standard 100m (328 ft.) Cat 5/5e/6 UTP cable to up to 200m at the same time.

1 In 2 Out

IEEE 802.3at (25W)

PoE PTZ IP Camera

Power

Data

IEEE 802.3at (25W)

Ultra PoE (60W)

1 In 4 Out

IEEE 802.3af (12W)

PoE Dome IP Camera

Power

Data

Ultra PoE (60W)

IEEE 802.3af (12W)

6. Power Over Ethernet Budget

The following table lists how many PoE devices can be powered by POE-E304:

Power Source

IEEE 802.3at PoE+ PSE

IEEE 802.3bt PoE PSE

External Power Adapter – 56V DC, 74W

1. The PoE Output Budget means the 4-port PD aggregated power output. The aggregated power consumption will be below 65 watts if with IEEE

802.3bt PoE++ PSE.

Note

2. If the PoE output, whose power source is IEEE

802.3at PoE+, is more than 25 watts, the device will be shut down.

PoE Output

Budget*

25 watts max.

65 watts max.

Max. Number of PDs

supported

Class 4 PD@25-watt 1 unit

Class 3 PD@15-watt 1 unit

Class 2 PD@7-watt 3 units

Class 4 PD@25-watt 2 units

Class 3 PD@15-watt 4 units

Class 2 PD@7-watt 4 units

Class 4 PD@25-watt 2 units

Class 3 PD@15-watt 4 units

Class 2 PD@7-watt 4 units

7. Customer Support

Thank you for purchasing PLANET products. You can browse our online

FAQ resource at PLANET web site rst to check if it could solve your

issue. If you need more support information, please contact PLANET support team.

PLANET online FAQs: https://www.planet.com.tw/en/support/faq.php?method=category&c1=2

PLANET support team mail address: support@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

- 10 -

- 12 - - 13 - - 14 -