PLANET POE-E201 User Manual

1. Introduction

Note

10/100/1000Base-T

Ethernet+DC

10/100/1000Base-T

OUT

IEEE 802.3at

Power over Gigabit Ethernet Extender

PoE OUT

LNK/ACT

PoE IN

OUT IN

26.50 22.50

1.1 Package Contents

Thank you for purchasing PLANET POE-E201 IEEE

802.3at Power over Gigabit Ethernet Extender, your Power over Gigabit Ethernet Extender package shall contains following contents:

Check the contents of your package for following parts:

 IEEE 802.3at Power over Gigabit Ethernet Extender x 1

 User's Manual x 1

If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.

1.3 TechnicalSpecication

Model POE-E201

Interfaces

1 x 10/100/1000Base-T Ethernet with

LAN IN

LAN OUT

Power over Ethernet

PoE Standard

PoE Power Supply Type

PoE Power Output 52V DC, 510mA, Max. 26 Watts

Power Pin Assignment

Maximum Distance

IEEE 802.3at / 802.3af PoE “Data + DC” in Auto MDI/MDI-X, Auto-negotiation RJ-45 connector

1 x 10/100/1000Base-T Ethernet with IEEE 802.3at / 802.3af PoE “Data + DC” out Auto MDI/MDI-X, Auto-negotiation RJ-45 connector

IEEE 802.3af Power over Ethernet IEEE 802.3at High Power over Ethernet

Mid-Span / Type B

4/5(+), 7/8(-)

4 units, daisy-chain installation with 500m support

10Base-T: 4-Pair UTP Cat. 5 up to 100m (328ft) 100Base-TX: 4-Pair UTP Cat. 5 up to

Network Cable

100m (328ft) 1000Base-T: 4-Pair UTP Cat. 5e, 6, up to 100m (328ft) EIA/TIA-568 100-ohm STP (100m, 328ft)

Standards Conformance

Regulation Compliance

FCC Part 15 Class A, CE

IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet

Standard Compliance

IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3af Power over Ethernet IEEE 802.3at High Power over Ethernet IEEE 802.3x Flow Control

Environment

Temperature: -10 ~ 60 Degree C

Operating

Relative Humidity: 5 ~ 95% (non-condensing)

Temperature: -40 ~ 85 Degree C

Storage

Relative Humidity: 5 ~ 95% (non-condensing)

Distance will often be shorter due to power delivery voltage-drop on the wire. The maximum distances will vary on the quality of the UTP cable and environment.

2.2 Ports Connection

Connect the PoE IN port from following

802.3at / 802.3af PSE device through a

IN Port

CAT-5/5e/6 UTP cable:

• PoE Injector • PoE Injector Hub

• PoE Ethernet Switch • Previous POE-E201

Connect the PoE OUT port to following

802.3at / 802.3af PD device through a

OUT Port

CAT-5/5e/6 UTP cable:

• PoE IP Camera • PoE VoIP Phone

• PoE Wireless AP • PoE Splitter

• Next POE-E201

2.3 LEDDenition:

LED Color Function

Lights to indicate the port is

PoE IN

LNK/ ACT

PoE OUT

Green

providing 52-56V (802.3at) / 48V (802.3af) DC in-line power.

Lights to indicate the port is link up. Blink: indicate that the extender is actively sending or receiving data over IN port.

Lights to indicate the port is providing 52-56V (802.3at) / 48V (802.3af) DC in-line power.

- 1 -

1.2 Key Features

 IEEE 802.3at / 802.3af Power over Ethernet compliant

 Complies with IEEE 802.3 / 802.3u / 802.3ab

10/100/1000Base-T

 Extends the range of PoE an additional 100 meters

(328ft.)

 Auto-detect and protect of PoE equipment from being

damaged by incorrect installation

 Multiple units, daisy-chain installation support

 Forwards both Ethernet data and PoE power to

remote device

 No external power cable installation required

 Compact size, Wall-mountable design

 Plug-and-Play installation

- 2 -

Hardware Specication

- 3 -

2. Hardware Description

- 5 -

- 7 -

3. Hardware Installation

Data Rate 10/100/1000Mbps

Switch Architecture

Switch Throughput

Maximum Frame Size

Flow Control

Store-and-Forward

10Mbps: 14880pps@64Bytes 100Mbps: 148810pps@64Bytes 1000Mbps: 1488000pps@64Bytes

1552Bytes

Back pressure for Half-Duplex IEEE 802.3x Pause Frame for Full-Duplex

• 1 x PoE IN (Green)

LED Indicators

• 1 x LAN Data (Green)

• 1 x PoE OUT (Green)

Protection

Dimension (W x D x H)

ESD (Ethernet): 2KV (TBD) Surge (EFT for power): 2KV (TBD)

94 x 70 x 26 mm

Weight 197g

Power Requirement

Power Consumption

IEEE 802.3at compliant with voltage within 52V-56V DC

3.2 Watts (system maximum)

Mechanical Metal / Wall Mountable

2.1 Product Outlook

This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same device and automatically distinguishes the speed of incoming connection.

This section describes the hardware features of POE-E201. Before connecting any network device to the POE-E201, read this chapter carefully.

3.1 Before Installation

Before your installation, it is recommended to check your network environment. If there is any far away IEEE 802.3at / 802.3af devices need to power on, the POE-E201 can provide you a way to supply power for this Ethernet device conveniently and easily.

The POE-E201 is installed between the PSE (Power Source Equipment) and the PD (Powered Device); it is powered by PSE and forwards the Ethernet data and remaining PoE power to the PD. The POE-E201 doesn’t require an external power supply and it can be installed

easily just plug and play; that means the operator does not need to congure the POE-E201. The POE-E201 injects power to the PDs without affecting the data

transmission performance. It offers a cost effective and quick solution to extend power and data an additional 100m.

- 4 -

- 6 -

- 8 -

Note

1. To provide you better PoE power and data

Note

PoE IP Camera

POE-E201

802.3at PoE Extender

802.3at PoE Injector

PoE PoE

Power

Data

Power

Data

Power

100M100M

200M

Power Line (AC)

Power Line (DC)

1000Base-T UTP

PoE

1000Base-T UTP with PoE

Note

POE-E201

802.3at PoE Ethernet Switch/Injector Hub

UPS

PoE

100M

PoE

100M

Outdoor IR IP Camera

non-PoE IP Camera

802.3at PoE Splitter

PoE

100M

PoE

100M

Power Output

300m 200m 100m 0m Distance

(20W)

400m

(16W)

500m

(12W) (24W) (30W)

POE-E201

802.3at PoE Extender

POE-E201

802.3at PoE Extender

POE-E201

PoE

100M

POE-E201

PoE

100M

POE-E201

PoE IP Camera

POE-E201

Power Line (AC)

Power Line (DC)

1000Base-T UTP

PoE

1000Base-T UTP with PoE

Note

extension quality, we strongly recommend that you use “Solid UTP Cable” when installing POE-E201.

2. The POE-E201 can be installed with third-party device if the device complied with IEEE 802.3at / 802.3af standard.

3.2 Connect POE-E201 to the Power Source Equipment (PSE)

There are 2 RJ-45 ports in the PoE Extender, of which the “IN” port functions as "PoE (Data and Power) input" and the “OUT” port on the other side functions as "PoE (Data and Power) output".

Step 1: Connect a standard Cat.5/5e/6 UTP cable from

Power Source Equipment (PSE), such as

PoE Switch, PoE Injector hub and single port PoE injector, to the “IN” port of POE-E201.

Step 2: The PSE delivers both Ethernet Data and PoE

power over UTP cable to the POE-E201 and the “PoE IN” LED will be steady on.

1. The POE IN LED turn on steady green means POE-E201 is being powered successfully with PoE class 0.

2. If POE IN LED does not turn on, please check the remote PSE or the cable with a PC or a network device to see if the cable is correct. Or with an IEEE 802.3at / 802.3af device such as

the target PD to check the power injection is

correct either.

3.4 Multiple PoE Extender Installation

The POE-E201 PoE Extender supports multiple units, daisy-chain installation. They can be employed in series for even longer distances based on remote PoE IP Camera or PoE Wireless Access Point power requirement.

Step 1: Connect the additional Cat.5/5e/6 cable from

the “OUT” port of the rst POE-E201, the other end of the UTP cable be used to connect to the “IN” port of remote / next POE-E201.

Step 2: The “PoE OUT” LED indicator of the rst

POE-E201 will be steady to shows it is providing power to next PoE Extender.

Step 3: The “PoE IN” LED on the next POE-E201 will

steady on.

3.3 Connect POE-E201 to the Powered Device (PD)

Step 3: Connect the additional Cat.5/5e/6 cable

that will be used to connect to the remote Powered Device (PD) to the “OUT” port of POE-E201.

Step 4: The "OUT" port is also the power injectors

which transmit DC Voltage to the Cat.5/5e/6 cable and transfer data and power simultaneously between the PSE and PD.

Step 5: Once POE-E201 detects the existence of an

IEEE 802.3at / 802.3af device, the “PoE OUT” LED indicator will be steady, ON to shows it is providing power.

1. If the connected device is not fully complying

2. According to IEEE 802.3at / 802.3af standard,

with IEEE 802.3at / 802.3af standard or in-line power device, the PoE OUT LED indicator of POE-E201 will not be steady on.

the POE-E201 will not inject power to the cable

if not connecting to a standard IEEE 802.3at /

802.3af device.

- 9 -

- 10 -

- 11 -

Step 4: Connect the additional Cat.5/5e/6 cable to the

remote PoE powered device to the “OUT” port of next or third POE-E201.

1. Per POE-E201 will take 3.2 Watts maximum for the system itself, please check the total power consumption of your IEEE 802.3at / 802.3af PD and the POE-E201 before you make the daisy-chain connection. If the overall power consumption is overloaded, the local PSE could shutdown the whole power system.

2. Per POE-E201 cable segment is limited in 100 meters Cat.5/5e/6 UTP wire from its IN/OUT port to the other data end, use of any other non standard cable or over distance could results in unstable connection.

- 12 - - 13 - - 14 -

3.5 Optional - DIN-Rail Mounting

There are two DIN-Rail holes on the left side of the POE-E201 that allows the Extender can be easily installed with DIN-Rail mounting. The PLANET optional DIN-Rail mounting Kit – RKE-DIN can be order separately. When need to replace the wall mount application with DIN-Rail application on the POE-E201,

please refer to following gures to screw the DIN-Rail on

the Extender. To hang the POE-E201, follow the below steps:

Step 1: screw the DIN-Rail on the POE-E201.

Step 2: Lightly press the button of DIN-Rail into the

track.

Step 3: Check the DIN-Rail is tightly on the track

You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.