PLANET POE-173 User Manual

Download

Page 1

1. Package Contents

Note

Thank you for purchasing PLANET Single-Port 10/100/1000Mbps Ultra PoE Injector, POE-173.

Model LAN Port Speed PoE Standard

Ultra PoE, backward

POE-173 10/100/1000Mbps

compatible with IEEE 802.3at/af standard

The term “Ultra PoE Injector” in the following section of this User’s Manual means the POE-173.

The box of the Single-Port 10/100/1000Mbps Ultra PoE Injector should contain the following items:

The Single-Port 10/100/1000Mbps Ultra PoE

Injector x 1

 User’s Manual x 1

 AC Power Cord x 1

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

PoE

Budget

60 watts

PD (Powered Device) such as IP phones, network cameras or wireless

Note

access points is a PoE-enabled terminal by PSE and thus it consumes energy.

3. Product Specications

Product POE-173

Hardware Specications

LAN 1 x RJ45 STP, “Data” Input Port

Interface

PoE

AC Connector

Ultra PoE

Network Cable

(60W)

802.3af / at PoE (15W / 30W)

LED Indicator

Data Rate 10/100/1000Mbps

Dimensions (W x D x H)

Weight 177g

Unit Output Voltage DC 50V, 1.2A

1 x RJ45 STP, “Data + Power” Output Port

1 x AC input power socket, IEC-320 C6

4-pair UTP Cat. 5, 5e, 6 up to 100m (328ft)

2-pair UTP Cat. 3, 4, 5, up to 100m (328ft)

System: Power x 1 (Green) PoE Port: Active, PoE ready / In Use x 1 (Green)

115 x 62.5 x 31 mm

4. Product Outlook

Figure 1: An overview of Ultra PoE Injector.

Figure 1: POE-173 Outlook

LED Indicators

LED Color Function

POWER Green

ACTIVE Green

It indicates that the Ultra PoE Injector has power.

It indicates the port is providing 50V DC in-line power.

The Ultra PoE Injector and POE-171S can be installed in pair. However, the use of the third-party device is allowed if the device complies with IEEE 802.3at Power over Ethernet Plus and a maximum of 30 watts of output capability.

Since the ultra PoE injector PoE port supports 50V DC PoE power output, please check and assure the Powered Device’s (PD) acceptable DC power range is 50V DC; otherwise, it will damage the Powered Device (PD).

Ultra PoE Injector Installation

Due to the backward capability of IEEE 802.3at/ af PoE standard, the Ultra PoE Injector can directly connect with any IEEE 802.3at/af end-nodes such as PTZ (Pan, Tilt & Zoom) speed dome network cameras, color touch-screen voice over IP (VoIP) telephones, and multi-channel wireless LAN access points. The screen in Figure 2 is shown below.

- 1 -

2. Product Features

 Interface

2 x RJ45 interface

1-Port Data + Power output

 1-Port Data input

 1 x AC 100-240V input power socket

 Power over Ethernet

 Ultra Power over Ethernet PSE

 Up to 60 watts of power on 4-pair UTP cable

 Backward compatible with IEEE 802.3at/af PD

device

Auto-detection of PoE IEEE 802.3at/af equip-

ment and devices to check whether there’s any damage done via incorrect installation

 Remote power feeding up to 100m

 Hardware

 All-in-one compact size design

 Internal power supply

 LED indicators for Power LED and Active LED

(PoE ready / In-use)

PSE (Power Sourcing Equipment) is a device (switch, or hub for instance) that will provide power in a PoE setup. The maximum allowed continuous output power per such device in IEEE 802.3af is

15.4 watts, in IEEE 802.3at is 30 watts and Ultra PoE is 60 watts.

- 3 -

Power Requirements

Power Consumption 60 watts max.

Operating Temperature 0 ~ 50 degrees C

Storage Temperature -10 ~ 70 degrees C

Operating Humidity

Storage Humidity

Power over Ethernet

PoE Standard

PoE Power Supply Type End-Span + Mid-Span

Power Pin Assignment

PoE Power Output

Standards Conformance

Standards Compliance

Regulation Compliance FCC Part 15 Class B, CE

100-240V AC @50/60Hz,

1.5A max.

5 ~ 95%, Relative Humidity, non-condensing

Ultra PoE over 4-pairs UTP cable, IEEE 802.3at High Power over Ethernet End-Span / Mid-Span PSE

Pair 1 End-Span: 1/2(+), 3/6(-) Pair 2 Mid-Span: 4/5(+), 7/8(-)

DC 50V / 60-watt PoE via 4-pairs DC 50V / 30-watt PoE via 2-pairs

IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3at Power over Ethernet Plus IEEE 802.3af Power over Ethernet

- 5 -

5. Hardware Installation

The following section describes the hardware features of Ultra PoE Injector. Before connecting any network device to the Ultra PoE Injector, read this chapter carefully.

5-1. Before Installation

The POE-173 is backward compatible with IEEE

802.3af PoE and IEEE 802.3at high power PoE standard. It is equipped with an AC power cord with 100-240V AC input and injects DC 50V power into the pin of the twisted pair cable (pair 1/2 [+], 3/6 [-] and pair 4/5[+], 7/8[-]) for 60-watt Ultra PoE injection.

Before connecting the POE-173 to your powered device (PD), please check to ensure that your powered device (PD) can accept 60-watt PoE power through pin 1/2 (+) & 3/6 (-) and pin 4/5 (+) & 7/8 (-). Otherwise, it will damage your powered device (PD).

Please also note: DO NOT connect POE-173 POE port to your non-POE network equipment Ethernet interface. Otherwise, it will damage your network equipment.

If there is difculty in nding a power socket for

AC-DC Adapter of your non-PoE network device, the Ultra PoE Injector and POE-171S (Ultra PoE Splitter) can provide you with DC power for this Ethernet device conveniently and easily.

- 7 -

100 meters

Switch

Data

Power

POE-173

Ultra PoE Injector

1000BASE-T UTP

PoE

1000BASE-T UTP with PoE

Figure 2: Connection to IEEE 802.3at / 802.3af Powered

Devices

1. Connect the AC power cord to “AC slot” of Ultra PoE Injector; the “POWER” LED will be on steadily.

2. Connect a standard network cable from Switch / workstation to “LAN” port of Ultra PoE Injector.

3. Connect the long cable to the port (PoE) of the remote PoE PD device.

4. Connect with IEEE 802.3at/af devices.

Once Ultra PoE Injector detects the existence of an IEEE 802.3at / 802.3af device, the ACTIVE LED indicator will be on steadily to show it is providing power.

Data

Power

PoE

PoE PTZ

IP Camera

Power Line (AC)

- 2 -

- 4 -

- 6 -

- 8 -

Page 2

Note

If the connected device is not fully complying with IEEE 802.3at / 802.3af Power over Ethernet or in-line power device, the LED indicator of Ultra PoE Injector will not be on steadily.

The Ultra PoE Injector and PoE Extender Installation

Below are steps showing how to install the PLANET Ultra PoE Injector (POE-173) and 802.3at PoE+ Extender (POE-E201) to extend the distance of networking.

The Ultra PoE Injector and Splitter Installation

Below are steps showing how to install the PLANET Ultra PoE Injector (POE-173) and Ultra PoE Splitter (POE-171S) in pair.

100 meters

Switch

Data

Power

POE-173

Ultra PoE Injector

PoE

Power

Data

PoE

POE-171S

Ultra PoE Splitter

1000BASE-T UTP

1000BASE-T UTP with PoE

Power 12V/19V/24V

Figure 3: Topology of the Connection of POE-173 and

POE-171S

- 9 -

Data

Power

Laptop

Power Line (AC)

Power Line (DC)

Data

Power

POE-173

Data +

Power

PoE PoE

802.3at PoE Extender

1000BASE-T UTP

PoE

1000BASE-T UTP with PoE

Data

100 meters100 meters

200 meters

Power

PoE IP Camera

Power Line (AC)

Figure 4: Topology of the Connection of POE-173 and

POE-E201

1. Connect the AC power cord to “AC slot” of Ultra PoE Injector; the “POWER” LED will be on steadily.

2. Connect a standard network cable from “POE” port of Ultra PoE Injector to the “IN” port of POE-E201.

3. The Ultra PoE Injector delivers both Ethernet Data and PoE power over UTP cable to the POE-E201 and the “ACTIVE” LED of Ultra PoE Injector and “PoE IN” LED of POE-E201 will light up continuously.

- 11 -

1. Connect the AC power cord to “AC slot” of Ultra PoE Injector; the “POWER” LED will be on steadily.

2. Connect a standard network cable from “POE” port of Ultra PoE Injector to “PoE In” port of POE-171S. The “ACTIVE” LED of Ultra PoE Injector and POE In-use LED of POE-171S will light up continuously.

3. Connect a standard network cable from Switch / workstation to “LAN” port of Ultra PoE Injector.

4. Connect the UTP cable in the package from “Ethernet” port of POE-171S to the RJ45 port of remote device.

5. Adjust proper DC power output and connect DC plug from “DC OUT” of POE-171S to remote device.

6. Power on the remote device and its power LED indicator will remain on.

Please make sure the POE-171S output voltage is correct before applying power to remote device. The POE-171S provides DC12V/19V/24V power output.

4. Connect the additional standard network cable to the remote Powered Device (PD) via the “OUT” port of POE-E201.

5. The “OUT” port is also the power injectors which transmits DC voltage to the standard network cable and transfer data and power simultaneously between the Ultra PoE Injector and PD.

6. Once POE-E201 detects the existence of an IEEE

802.3at / 802.3af device, the “PoE OUT” LED indicator will be on steadily to show it is providing power.

1. If the connected device is not fully complying with IEEE 802.3at /

802.3af standard or in-line power device, the PoE OUT LED indicator of POE-E201 will not be on steadily.

2. According to IEEE 802.3at / 802.3af standard, the POE-E201 will not inject power to the cable if not connected to a standard IEEE 802.3at / 802.3af device.

Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQ resource at the PLANET

Web site rst to check if it could solve your issue. If

you need more support information, please contact PLANET switch support team.

PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=2

Switch support team mail address : support_switch@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

EC Declaration of Conformity

For the following equipment:

*Type of Product : Single-Port 10/100/1000Mbps Ultra PoE Injector (60 Watts)

*Model Number : POE-173

* Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.).

is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC). For the evaluation regarding the EMC, the following standards were applied:

EN55022 (2006 + A1:2007 + A2:2010) EN 61000-3-2 (2006 + A1:2009 + A2:2009) EN 61000-3-3 (2008) EN55024 (2010) IEC 61000-4-2 (2008) IEC 61000-4-3 (2006+A1: 2007 + A2:2010) IEC 61000-4-4 (2004 + A1:2010) IEC 61000-4-5 (2005) IEC 61000-4-6 (2008) IEC 61000-4-8 (2009)

IEC 61000-4-11 (2004)

Responsible for marking this declaration if the:

 Manufacturer  Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Ta ipei City 231, Taiwan

Person responsible for making this declaration

Name, Surname Kent Kang

Position / Title : Product Manager

Taiwan 24thMay, 2013

Place Date Legal Signature

PLANET TECHNOLOGY CORPORATION

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-22 19-9518 Fax:886-2-2219-9528

e-mail: sales@planet.com.tw http://www.planet.com.tw

(R.O.C.)

- 10 -

- 12 - - 13 -