Single-Port 10/100/1000Mbps
Ultra PoE Injector (60 Watts)
POE-171
Single-Port 10/100/1000Mbps
Ultra PoE Splitter (12V/19V/24V)
POE-171S
User’s Manual
Version 1.0
Trademarks
Copyright © PLANET Technology Corp. 2013.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will
work properly in all environments and applications, and makes
no warranty and representation, either implied or expressed,
with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual
is accurate; PLANET disclaims liability for any inaccuracies or
omissions that may have occurred.
Information in this User’s Manual is subject to change without
notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies
that may be contained in this User’s Manual. PLANET makes no
commitment to update or keep current the information in this
User’s Manual, and reserves the right to make improvements to
this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice. If you nd information in
this manual that is incorrect, misleading, or incomplete, we
would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause
harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode
operation.
For energy saving, please remove the power cable to disconnect
the device from the power circuit.
Without removing power cable, the device will still consuming
power from the power source. In view of Saving the Energy
and reducing the unnecessary power consumption, it is strongly
suggested to remove the power connection for the device if this
device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances in
electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the
crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste; WEEE should be collected separately.
Revision
PLANET Single-Port 10/100/1000Mbps Ultra PoE Injector User’s
Manual
For Model: POE-171 and POE-171S
Revision: 1.1 (August, 2013)
Part No.: 2350-AF0430-001
Table of Contents
1. Package Contents ............................................................. 5
2. Product Features............................................................... 6
3. Product Specications ....................................................... 8
4. Product Outlook .............................................................. 12
5. Hardware Installation ...................................................... 14
5.1 Before Installation ..................................................... 14
5.2 The POE-171 Installation ........................................... 14
5.3 The POE-171 and POE-171S Installation ..................... 16
5.4 The POE-171 and POE-E201 Installation ..................... 17
6. Customer Support .......................................................... 19
1. Package Contents
Thank you for purchasing PLANET Single-Port 10/100/1000Mbps
POE-171 or POE-171S.
Model LAN Port Speed PoE Standard PoE Budget
POE-171 10/100/1000Mbps IEEE 802.3at/af 60 watts
Model LAN Port Speed PoE Standard DC Out
POE-171S 10/100/1000Mbps IEEE 802.3at/af 12V/19V/24V
Please unpack the box of the POE-171 or POE-171S carefully,
and the box should contain the following items:
[POE-171]
The Single-Port 10/100/1000Mbps ultra PoE injector x 1 l
User’s manual x 1 l
65W power adaptor x 1 l
[POE-171S]
The Single-Port 10/100/1000Mbps ultra PoE splitter x 1 l
User’s manual x 1 l
DC plug cable x 2 l
15cm RJ45 cable x 1 l
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair.
5
2. Product Features
[POE-171]
Interface
2-Port RJ-45 interfaces l
1-Port Data + Power output
1-Port Data input
1 DC 52~56V input power socket l
Power over Ethernet
Ultra Power over Ethernet End-Span / Mid-Span PSE l
IEEE 802.3at PoE compliant l
Backward compatible with IEEE 802.3af PD device l
Supports PoE Power up to 60 watts for PoE port l
Auto-detection of PoE IEEE 802.3at/af equipment and l
devices from being damaged by incorrect installation
Remote power feeding up to 100m l
[POE-171S]
Interface
2-Port RJ-45 interfaces l
1-Port Data + Power input
1-Port Data output
1-Port DC output power socket l
1 DC 12V/19V/24V DIP switch l
Power over Ethernet
Complies with ultra Power over Ethernet End-Span/Mid- l
Span PSE
IEEE 802.3at PoE compliant l
6
Splits the 56V DC power over RJ-45 Ethernet cable into DC l
Note
12V/19V/24V output
Distance up to 100 meters l
IEEE802.3af Injector devices compatible l
Hardware
Metal case l
LED indicators for Power LED and PoE In-use LED l
Standard Compliance
IEEE 802.3 10Base-T l
IEEE 802.3u 100Base-TX l
IEEE 802.3ab 1000Base-T l
IEEE 802.3at High Power over Ethernet l
IEEE 802.3af Power over Ethernet l
FCC Part 15 Class A, CE l
PSE (Power Sourcing Equipment) is a device
(switch, or hub for instance) that will provides
power in a PoE setup. Maximum allowed continuous output power per such device in IEEE
802.3af is 15.4W, and in IEEE 802.3at is 30W.
PD (Powered Device) is a PoE-enabled terminal
by PSE and thus consumes energy, such as PoE
IP Phones, PoE IP cameras, PoE wireless access
points, etc.
7
3.Product Specications
Product POE-171
Hardware Specications
LAN Ethernet 1 x RJ-45 STP, “Data” Input Port
Interface
Network
Cable
LED Indicator
Data Rate 10/100/1000Mbps
Dimensions (W x D x H) 94 x 70.3 x 26.2 mm
Weight 237g
Unit Output Voltage DC 56V, 1.16 A
Power Requirements 100-240V AC, 50/60Hz, 1.5A
Power Consumption 60 Watts max.
Number of devices can be
powered
Operating Temperature 0 ~ 50 degrees C
Storage Temperature -10 ~ 70 degrees C
Operating Humidity
Ethernet+DC
(PoE)
Power 1 x DC 56V Input socket
Ultra PoE (60W)
802.3af/at PoE
(15W / 30W)
1 x RJ-45 STP, Data + Power”
Output Port
4-Pair UTP Cat. 3, 4, 5, up to
100m (328ft)
2-Pair UTP Cat. 3, 4, 5, up to
100m (328ft)
System: Power x 1 (Green)
PoE Port: PoE In-use x 2 (Green)
1
5 ~ 90%, Relative Humidity,
non-condensing
8
Storage Humidity
Power over Ethernet
PoE Standard
PoE Power Output Budget DC 56V / 60 Watts
PoE Power Supply Type End-Span + Mid-Span
Power Pin Assignment
Standards Conformance
Standards Compliance
Regulation Compliance FCC Part 15 Class A, CE
5 ~ 90%, Relative Humidity,
non-condensing
Ultra PoE over 4-pair UTP,
IEEE 802.3at High Power over
Ethernet End-Span / Mid-Span
PSE
Pair 1 End-Span: 1/2(-), 3/6(+)
Pair 2 Mid-Span: 4/5(+), 7/8(-)
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast
Ethernet
IEEE 802.3ab 1000Base-T Gigabit
Ethernet
IEEE 802.3at High Power over
Ethernet
IEEE 802.3af Power over Ethernet
9
Product POE-171S
Hardware Specications
Ethernet
Interface
Network
Cable
LED Indicator
Data Rate 10/100/1000Mbps
Dimensions (W x D x H) 94 x 70.3 x 26.2 mm
Weight 300g
Unit Output Current
(at 56V Input)
Power Consumption 54 watts max.
Number of devices can be
powered
Operating Temperature 0 ~ 50 degrees C
Storage Temperature -10 ~ 70 degrees C
Operating Humidity
PoE In
Power socket 1 x DC out power socket
Ultra PoE (60W)
802.3af/at PoE
(15W / 30W)
1 x RJ-45 STP, Ethernet data
output port
1 x RJ-45 STP, PoE power input
port
4-Pair UTP Cat. 3, 4, 5, up to
100m (328ft)
2-Pair UTP Cat. 3, 4, 5, up to
100m (328ft)
System: Power x 1 (Green)
PoE In-use x 2 (Green)
4.2A@12V DC
2.6A@19V DC
2.1A@24V DC
1
5 ~ 90%, Relative Humidity,
non-condensing
10
Storage Humidity
Power over Ethernet
PoE Standard
PoE Power Output Budget DC 56V / 50 Watts
PoE Power Supply Type End-Span / Mid-Span
Power Pin Assignment 1/2(-), 3/6(+) / 4/5(+), 7/8(-)
Standards Conformance
Standards Compliance
Regulation Compliance FCC Part 15 Class A, CE
5 ~ 90%, Relative Humidity,
non-condensing
IEEE 802.3at High Power over
Ethernet End-Span / Mid-Span PD
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast
Ethernet
IEEE 802.3ab 1000Base-T Gigabit
Ethernet
IEEE 802.3at High Power over
Ethernet
IEEE 802.3af Power over Ethernet
11
4. Product Outlook
Ethernet + DC
POE-171
60W PoE Injector
PWR
802.3at End-Span
802.3at Mid-Span
60W Ul tra
Power over Etherne t
Inject or
PoE In-use
52~56V DC IN
10/100/1000Base-T
Ethernet
PWR
End-Span PoE Input
Mid-Span PoE Input
PoE In
DC Out Ethernet
12V 19V 24V
POE-171S
60W PoE Splitter
60W Ul tra
Power over Etherne t
Splitt er
Incorrect voltage might cause device damage
CAUTION
Disconnect “PoE In” cable
before changing Voltage
Note
PoE In
Figure 1: shows overview of POE-171.
Figure 1: POE-171 Outlook
Figure 2: shows overview of POE-171S.
Figure 2: POE-171S Outlook
12
POE-171 LED Indicators
LED Color Function
PWR Green
802.3at
End-Span
802.3at
Mid-Span
POE-171S LED Indicators
LED Color Function
PWR Green
End-Span
PoE Input
Mid-Span
PoE Input
Lights to indicate the ultra PoE injector has
power.
Lights to indicate the ultra PoE injector is
Green
working in End-Span mode and offers up
to 30 watts of power.
Lights to indicate the ultra PoE injector is
Green
working in Mid-Span mode and offers up to
30 watts of power.
Lights to indicate the ultra PoE splitter has
power.
Lights to indicate the ultra PoE splitter is
Green
working in End-span mode
Lights to indicate the ultra PoE splitter is
Green
working in Mid-span mode
13
5. Hardware Installation
Note
The following section describes the hardware features of PoE-171
and POE-171S. Before connecting any network device to them,
please read this chapter carefully.
Please refer to following sections for detailed information about
POE-171
5.1 Before Installation
Before your installation, it is recommended to check your
network environment. If there is any IEEE 802.3at device that
needs higher power to be powered on and works normally,
the POE-171 provides you with a way out to supply power to
this Ethernet device conveniently and easily. The POE-171 is
equipped with a power adaptor which is 100-240V AC input and
injects DC 56V power into the pin of the twisted pair cable (pair
1/2 [-], 3/6 [+] and pair 4/5[+], 7/8[-]).
If there is difculty in nding a power socket for AC-DC adapter
of your non-PoE IEEE 802.3at networked device, the POE-171
and POE-171S (Ultra PoE Splitter) provide you with a way out to
supply DC power to this Ethernet device conveniently and easily.
The POE-171 and POE-171S can be installed in
a pair. However, the use of third-party device is
allowed if the device complies with IEEE 802.3at
Power over Ethernet.
5.2 The POE-171 Installation
1. Connect the AC power adaptor to “52-56V DC IN” of
POE-171; the “PWR” LED will be steadily on.
14
2. Connect a standard Ethernet cable from an Ethernet switch or
Switch
100 meters
PoE
Power
Data
PoE PTZ
IP Camera
Power
Data
AC
1000Base-T UTP
PoE
1000Base-T UTP with PoE
Power Line (AC)
AC
POE-171
Ultra PoE Injector
PC workstation to “Ethernet” port of POE-171.
3. Connect the long cable to “Ethernet+DC” port.
4. Connect with IEEE 802.3at/802.3af devices. Due to the
capability of IEEE 802.3at/802.3af Power over Ethernet, the
POE-171 can directly connect with any IEEE 802.3at/802.3af
end-nodes, such as PTZ (Pan, Tilt & Zoom) network cameras,
PTZ speed dome, color touch-screen, Voice over IP (VoIP)
telephones and multi-channel wireless LAN access points
which support IEEE 802.3at/802.3af In-line Power over
Ethernet port. The screen in Figure 3 appears.
Figure 3: Connecting architecture with IEEE 802.3at/802.3af devices
Once POE-171 detects the existence of an IEEE 802.3at/802.3af
device, the PoE In-use LED indicator will be steadily on to show
it is providing power.
15
Note
1. Since the PoE port of PoE-171 supports 52-56V
Note
DC PoE power output, please check and assure
the powered device (PD) accepts DC power
range of 52-56V DC. Otherwise, it will damage
the powered device (PD).
2. If the connected device is not fully complied
with IEEE 802.3at/802.3af Power over Ethernet
or in-line power device, the LED indicator of
POE-171 will not be steadily on.
5.3 The POE-171 and POE-171S Installation
Please turn off POE-171S before you switch DC
power output mode.
1. Adjust proper DC power output and connect DC plug from
“DC OUT” of POE-171S to remote device.
2. Connect the power adaptor to “52-56V DC IN” of POE-171;
the “PWR” LED will be steadily on.
3. Connect a standard Ethernet cable from “Ethernet+DC” port
of POE-171 to “PoE In” port of POE-171S. The “802.3at
End-Span” and “802.3at Mid-Span” LED of POE-171 and
POE-171S will light up continuously.
4. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to “Ethernet” port of POE-171.
5. Connect a standard Ethernet cable from “Ethernet” port of
POE-171S to the remote Ethernet device.
6. Turn on the remote device and its power LED indicator will
remain on.
16
Switch
Power 12V/19V/24V
POE-171S
100 meters
Power
Data
Power
Data
PoE
Power
Data
AC
DC
Laptop
1000Base-T UTP
PoE
1000Base-T UTP with PoE
Power Line (AC)
AC
DC
Power Line (DC)
POE-171
Ultra PoE
Splitter
Ultra PoE Injector
Figure 4: Connected architecture over POE-171 and POE-171S
Note
1. According to IEEE 802.3at/802.3af Power
over Ethernet, the POE-171 will not inject
power to the cable if not connected to IEEE
802.3at/802.3af device.
2. Please ensure the POE-171S output voltage is
correct before applying power to remote device.
The POE-171S provides DC12V/19V/24V power
output.
5.4 The POE-171 and POE-E201 Installation
1. Connect the power adaptor to “52-56V DC IN” of POE-171;
the “PWR” LED will be steadily on.
2. Connect a standard Ethernet cable from “Ethernet+DC” port
of ultra PoE injector to the “IN” port of POE-E201.
3. The ultra PoE injector delivers both Ethernet Data and PoE
power over UTP cable to the POE-E201 and the POE In-use
17
LED of POE-171 and “PoE IN” LED of POE-E201 will light up
802.3at
PoE Extender
Data
PoE PoE
+
Power
Power
Data +
Power
Data
100 meters100 meters
200 meters
Power Line (AC)
AC
1000Base-T UTP
PoE
1000Base-T UTP with PoE
PoE IP Camera
POE-171
Note
continuously.
4 Connect the additional standard Ethernet cable that will be
used for connecting to the remote powered device (PD) to the
“OUT” port of POE-E201.
5. The “OUT” port is also the power injectors which transmit DC
Voltage to the standard network cable and transfer data and
power simultaneously between the POE-171 and PD.
6 Once POE-E201 detects the existence of an IEEE
802.3at/802.3af device, the “PoE OUT” LED indicator will be
steadily ON to show it is providing power.
Figure 5: Connected architecture over POE-171 and POE-E201
1. If the connected device is not fully complied
with IEEE 802.3at/802.3af standard or in-line
power device, the PoE OUT LED indicator of
POE-E201 will not be steadily on.
2. According to IEEE 802.3at/802.3af standard, the POE-E201 will not inject power to
the cable if not connected to a standard IEEE
802.3at/802.3af device.
18
6. Customer Support
Thank you for purchasing PLANET products. You can browse our
online FAQ resource at the PLANET Web site rst to check if it
could solve your issue. If you need more support information,
please contact PLANET switch support team.
PLANET online FAQ :
http://www.planet.com.tw/en/support/faq.php?type=2
Switch support team mail address :
support_switch@planet.com.tw
Copyright © PLANET Technology Corp. 2013.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
19
EC Declaration of Conformity
For the following equipment:
*Type of Product :
Single-Port 10/100/1000Mbps Ultra PoE Injector (60 Watts)
Single-Port 10/100/1000Mbps Ultra PoE Splitter (12V/19V/24V)
*Model Number : POE-171
POE-171S
* Produced by:
Manufacturer‘s Name : PLANET Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.).
Is here with confirmed to comply with the requirements set out in the Council Directive
on the Approximation of the Laws of the Member States relating to Electromagnetic
Compatibility (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN 55022 (Class A : 2006+A1:2007)
EN 55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2006+A1:2008+A2:2010)
IEC 61000-4-4 (2004+A1:2010)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2008)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
(R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan 22, July, 2013
Place Date Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: sales@planet.com.tw http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
Loading...