PLANET POE-161 User Manual

Download

IEEE 802.3at Gigabit

High Power over Ethernet Adapter

POE-161 / POE-161S

User’s Manual

Trademarks

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or

tness for a particular purpose.

PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.

Information in this User’s Manual is subject to change without notice and does not represent a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s

Manual, at any time without notice. If you nd information in

this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Energy Saving Note of the Device

This power required device does not support Stand by mode operation.

For energy saving, please remove the DC-plug or push the hardware Power Switch to OFF position to disconnect the device from the power circuit. Without removing the DC-plug or switch off the device, the device will still consume power from the power source. In the view of Saving the Energy and reduce the unnecessary power consuming, it is strongly suggested to power off or to remove the DC-plug for the device if this device is not intended to be active.

WEEE Warning

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic

equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

PLANET IEEE 802.3at Gigabit High Power over Ethernet Adapter User’s Manual

For Models:

IEEE 802.3at Gigabit High Power over Ethernet Injector:

POE-161

IEEE 802.3at Gigabit High Power over Ethernet Splitter:

POE-161S

Revision: 1.0 (January, 2010)

Part No.: 2350-AF0280-000

Table Of Contents

1. Package Content ...............................................................6

2. Product Features

3. Product Specication .......................................................

4. Product Outlook ..............................................................

5. Hardware Installation ......................................................

5-1 POE-161 ................................................................. 16

5-2 POE-161S ............................................................... 19

Customer Support ............................................................. 23

............................................................... 7

1. Package Content

Thank you for purchasing PLANET IEEE 802.3at High Power over Ethernet Adapter, POE-161 and POE-161S. Terms of “802.3at PoE Injector” in following section of this User’s Manual means the POE-161, Terms of “802.3at PoE Splitter” in following section of this User’s Manual means the POE-161S.

Upon open the box of the IEEE 802.3at High Power over Ethernet Adapter and carefully unpack it. The box should contain the following items:

POE-161:

The IEEE 802.3at Gigabit High Power over Ethernet Injector

x 1

User’s Manual x 1

DC 56V Power Adapter x 1

Power Cord x 1

POE-161S:

The IEEE 802.3at Gigabit High Power over Ethernet Splitter

x 1

User’s Manual x 1

15cm UTP Straight Network Cable x 1

DC Plug cable x 2

If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.

2. Product Features

POE-161:

Interface

2-Port RJ-45 interfaces

1-Port Data + Power output

≤

1-Port Data input

≤

1 DC 56V input power socket

PoE

Gigabit High Power over Ethernet Mid-Span PSE

Pre-IEEE 802.3at compliant

IEEE 802.3af splitter devices compatible

Support PoE Power up to 30 Watts for PoE port

Up to 1 IEEE 802.3at devices powered

Provides DC 56V power over RJ-45 Ethernet cable to device

with Ethernet port

Auto-detect of POE IEEE 802.3at equipment and devices

from being damaged by incorrect installation

Remote power feeding up to 100m

Hardware

Plastic case

LED indicators for Power LED and PoE In-use

Standard Compliance

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX

IEEE 802.3ab 1000Base-T

IEEE 802.3at Power over Ethernet pre-standard

FCC Part 15 Class A, CE

POE-161S:

Interface

2-Port RJ-45 interfaces

1-Port PoE Power+ Data input

≤

1-Port Data output

≤

1 DC out plug connector

PoE

Complies with IEEE 802.3at Power over Ethernet pre-stan-

dard, PD

Splits the 56V DC power over RJ-45 Ethernet cable into DC

5V/12V output

Up to 1 non-IEEE 802.3at devices powered

Auto-detect of PoE IEEE 802.3at equipment, protect devices

from being damaged by incorrect installation

Adjustable two different output voltage options (5V/4.5A,

12V/2A) to t various devices

Distance up to 100 meters

IEEE 802.3af Injector devices compatible

Hardware

Plastic case

5V /12V DIP switch

LED indicators power input indication

Standard Compliance

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX

IEEE 802.3ab 1000Base-T

IEEE 802.3at Power over Ethernet pre-standard

FCC Part 15 Class A, CE

Note

PSE (Power Sourcing Equipment) is a device (switch, or hub for instance) that will provide power in a PoE setup. Maximum allowed continuous output power per such device in IEEE 802.3af is 15.4W, 30W in IEEE 802.3at pre-standard.

PD (Powered Device) is a PoE-enabled terminal by PSE and thus consumes energy, such as IP Phones, network cameras and Wireless access points, etc

3. Product Specication

POE-161:

Product POE-161

Hardware Specication

“Data” Input Port 1 x RJ-45 STP

“PoE (Data+Power)”

Interface

LED Indicator

Network Cable

Data Rate 10/100/1000Mbps

Dimension (W x D x H) 95 x 70 x 25 mm

Weight 83g

Unit Input Voltage DC 56V, 0.53A

Power Requirement 100-240V AC, 50/60Hz

Power Consumption 30 Watts max.

Number of device can be powered

Operating Temperature 0 ~ 50 Degree C

Storage Temperature -10 ~ 70 Degree C

Humidity 5 ~ 95% (Non-condensing)

Output Port

DC 56V Input power socket

1 x RJ-45 STP

System: Power x 1 (Green) PoE Port: PoE in Use x 1 (Green)

10Base-T: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328ft) 100Base-TX: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328ft) 1000Base-T: 2-Pair UTP Cat. 5, 5e, 6 up to 100m (328ft) EIA/TIA- 568 100-ohm STP (100m)

Power over Ethernet

PoE Standard

PoE Power Output DC 56V / 30 Watts

PoE Power supply Type Mid-Span

Power Pin Assignment 4/5(+), 7/8(-)

Standards Conformance

Standards Compliance

Regulation Compliance FCC Part 15 Class A, CE

IEEE 802.3at High Power over Ethernet pre-standard / Mid-Span PSE

IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3at Power over Ethernet prestandard

POE-161S:

Product POE-161S

Hardware Specication

“Data” Out Port 1 x RJ-45 STP

“PoE (Power+Data)”

Interface

LED Indicator System: PoE In x 1 (Green)

Network Cable

Data Rate

DIP Switch 5V DC / 12V DC output voltage

Dimension (W x D x H) 95 x 70 x 25 mm

Weight 111g

Number of device can be powered

Operating Temperature 0 ~ 50 Degree C

Storage Temperature -10 ~ 70 Degree C

Humidity 5 ~ 95% (Non-condensing)

Power over Ethernet

PoE Standard

Input Port

DC Out Plug Connector

1 x RJ-45 STP

10Base-T: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328ft) 100Base-TX: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328ft) 1000Base-T: 2-Pair UTP Cat. 5, 5e, 6 up to 100m (328ft) EIA/TIA- 568 100-ohm STP (100m)

10/100/1000Mbps (vary on Ethernet device attached)

IEEE 802.3at High Power over Ethernet pre-standard / PD

Standards Conformance

IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet

Standards Compliance

Regulation Compliance FCC Part 15 Class A, CE

IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3at Power over Ethernet prestandard

4. Product Outlook

Figure 1 shows a front panel of 802.3at PoE Injector.

Figure 1: POE-161 Outlook

LED Indicators

LED Color Function

PWR Green

PoE In-use Green

Lights to indicate that the POE-161 has power.

Lights to indicate the port is providing 56V DC in-line power.

Figure 2 shows a front panel of 802.3at PoE Splitter.

Figure 2: POE-161S Outlook

LED Indicators

LED Color Function

PoE In Green

Lights to indicate the port is providing 56V DC in-line power.

5. Hardware Installation

Note

This IEEE 802.3at Gigabit High Power over Ethernet Adapter provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same device and automatically distinguishes the speed of incoming connection. Please refer to following sections for detail information about IEEE 802.3at Gigabit High Power over Ethernet Adapter.

5-1 POE-161

The following section describes the hardware features of POE-

161. Before connecting any network device to the POE-161, read this chapter carefully.

Before Installation

Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3at devices need higher power to power on and work normally, the POE-161 can provide you a way to supply power for this Ethernet device conveniently and easily. The POE-161 equips with an AC-DC adapter with DC 56V input and injects this DC power into the pin of the twisted pair cable (pair 4, 5 and pair 7, 8).

If there is very difcult to nd a power socket for AC-DC

Adapter of your non IEEE 802.3at networked device, the POE161 and POE-161S can provide you a way to supply DC power for this Ethernet device conveniently and easily.

The POE-161 and POE-161S can be installed in pair. However, the use of third-party device is allowed if the device complied with IEEE 802.3at Power over Ethernet pre-standard.

POE-161, the Injector Installation

Switch

100 meters

PoE

Power

Data

PTZ Speed

Dome

POE-161

Power

Data

1000Base-T UTP

PoE

1000Base-T UTP with PoE

Power Line (AC)

1. Connect the AC adapter to “DC 56V” of POE-161. The power

LED will be steady on.

2. Connect a standard network cable from Switch/workstation to

“Ethernet” port of POE-161.

3. Connect the long cable that will be used to connect to the

remote device to the port “Ethernet + DC”.

4. Connect with IEEE 802.3at devices, due to the capability of

IEEE 802.3at Power over Ethernet pre-standard, the POE161 can directly connect with any IEEE 802.3at end-nodes such as PTZ (Pan, Tilt & Zoom) network cameras, PTZ Speed Dome, color touch- screen Voice over IP (VoIP) telephones, multi- channel wireless LAN access points where support IEEE

802.3af In-line Power over Ethernet port. The screen in Figure 3 appears.

Figure 3: Connection to IEEE 802.3at device

Once POE-161 detects the existence of an IEEE 802.3at device,

Note

the POE In-use LED indicator will be steady on to shows it is providing power.

If the connected device is not fully complying with IEEE 802.3at Power over Ethernet pre-standard or in-line power device, the LED indicator of POE-161 will not be steady on.

POE-161 and POE-161S, the IEEE 802.3at Injector Splitter Installation

1. Connect the AC adapter to “DC 56V” of POE-161. The power

LED will be steady on.

2. Connect a standard network cable from

of POE-161 to “PoE In” port of POE-161S. The POE In-use LED of POE-161 / POE-161S will light on continuance.

3. Connect a standard network cable from Switch/workstation to

“Ethernet” port of POE-161.

4. Connect the UTP cable in the package from

of POE-161S to the RJ-45 port of remote device.

5. Adjust proper DC power output and connect DC plug from

“DC OUT” of POE-161S to remote device.

6. Power on the remote device and its power LED indicator will

remains on.

“Ethernet+DC” port

“Ethernet” port

Switch

POE-161SPOE-161

100 meters

Power

Data

Power

Data

PoE

Power

Data

PTZ Camera

1000Base-T UTP

PoE

1000Base-T UTP with PoE

Power Line (AC)

Power Line (DC)

Figure 4: Connection architecture over POE-161/POE-161S

Note

1. According to IEEE 802.3at Power over Ethernet pre-standard, the POE-161 will not inject power to the cable if not connecting to IEEE 802.3at devices.

2. Please ensure the output voltage is correct before applying power to remote device.

5-2 POE-161S

The following section describes the hardware features of POE161S. Before connecting any network device to the POE-161S, read this chapter carefully.

Before Installation

If your network environment is very difcult to nd a power

socket for your AC-DC Adapter of networked device, the POE161S provide DC power for this Ethernet Device conveniently and easily.

The POE-161S separates the power out and provide two kind

Hint

of DC power output through its DIP switch and its voltage and current shown as below:

- 5V DC / 4.5A

- 12V DC / 2A

The default value will be set on 5V.

Please check the power requirement of the device that is going to get the power from POE-161S. If the power requirement is higher than POE-161S can supply, current overload will shutdown the POE-161S itself. Thus, it will shutdown your device as well.

POE-161 and POE-161S can be installed in pair. However, use of third-party device is allowed if the device complied with IEEE

802.3at Power over Ethernet pre-standard.

POE-161S, the Splitter Installation

Switch

POE-161SPOE-161

100 meters

Power

Data

Power

Data

PoE

Power

Data

PTZ Camera

1000Base-T UTP

PoE

1000Base-T UTP with PoE

Power Line (AC)

Power Line (DC)

Warning

Caution

1. Connect a standard network cable from

“Ethernet+DC” port of POE-161 to “PoE In” port of POE-161S. The POE LED of POE-161S / POE-161 will light on continuance.

The POE-161S only accept IEEE 802.3at or IEEE

802.3af equipment; other in-line power device may cause the POE-161S malfunction.

2. Connect the UTP cable in the package from

“Ethernet” port

of POE-161S to the RJ-45 port of remote device.

3. Adjust proper DC power output and connect DC plug from “DC OUT” of POE-161S to remote device.

Please ensure the output voltage is correct for remote device. Otherwise, it will damage your remote device.

4. Power on the remote device and its LED indicator will remains on.

Connect with 802.3at devices

Power Line (DC)

100 meters

PTZ Speed

Dome

1000Base-T UTP

PoE

1000Base-T UTP with PoE

802.3at in-line power Switch

PoE

Power

Data

POE-161S

Power

Data

Hint

The POE-161S also provide the alternative to make the non IEEE

802.3at devices the possibility to connect with an IEEE 802.3at

in-line power device like Power over Ethernet Injector or Power

over Ethernet Switch, the gure is as below.

With IEEE 802.3at Power over Ethernet pre-standard; the POE-161S also can co-work with IEEE

802.3at End-Span High Power over Ethernet Switch that feeding power over pin 1, 2, and 3, 6. For example: the WGSD-8020P.

Customer Support

Thank you for purchase PLANET products. You can browse our

online FAQ resource at the PLANET Web site rst to check if it

could solve you issue. If you need more support information, please contact PLANET switch support team.

PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=2

Switch support team mail address : support_switch@planet.com.tw

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

This page is intentionally left blank

PLANET POE-161 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual