Planet MAP-2105 User Manual

Copyright
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.
Copyright
2006 by PLANET Technology Corp. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed “as is”. Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.
Revision
Quick Start Guide for PLANET MESH WLAN Mobile IP Server
Model: MAP-2105
Rev: 1.1 (June, 2006)
Part No. EMQ-MAP2105
Table of Contents
1. Preference 1
2. Package Contents 1
3. Network Planning 1
4. Hardware Installation Procedures 2
5. Startup the MAP-2105 2
6. Basic Network Setup 3
7. Further Configuration 6
1
1. Preference
The MAP-2105 is a Mobile IP server for PLANET Wireless Mesh Network. It is also called as MLRD, Mobile Location Register Daemon. This Quick Start Guide illustrates basic information to start up the MAP-2105, please refer to the following for the first time start up. More information can be found in the CD-ROM, it is strongly recommended to check both documents to help you better understanding the device.
2. Package Contents
The following items should be included:
• MAP-2105 x 1
• Power Adapter x 1
• Quick Start Guide x 1
• Management Utility and User’s manual CD x 1
If any of the above items are damaged or missing, please contact your dealer immediately.
3. Network Planning
3.1 Installation topology
The basic MESH Network topology can be planned as following.
The MAP-2105 should connect to the network that provide DHCP services (the first time installation) In this guide, we will base on XRT-401D (Internet Broadband Router) as the example for DHCP server, switch and router, this installation can vary on the network planning.
The MAP-2105 should be installed in the same subnet to the Mesh Gateway for optimal performance.
2
Hint:
The MAP-2105 is optimized for 500-user registration; however, the
overall network performance may vary on the real environment and
application in many aspects, such as the bandwidth to the Internet, the
services / sessions that the clients implement.
3.2 Installation consideration
3.2.1 Software consideration
The MAP-2105 provides the two management interfaces:
• Secured Web access
• Management utility
For the first time management, please follow the below section to access the MAP-2105 through web browser.
The management utility helps to manage the MAP-2105 via SNMP. This utility can be installed in a Windows PC that located in the same LAN as MAP-2105. For more information about Management utility, please also refer to the management utility guide.
4. Hardware Installation Procedures
1. Using Category 3 or higher UTP or STP cable, connect the WAN port of MAP-
2105 to a 10Mbps or 10/100Mbps Ethernet hub or switch, and connect the
management station to a hub or switch on the same LAN.
2. Connect the power adapter to the receptor on MAP-2105 and plug the other
end to a wall outlet or power strip.
Note:
ONLY use the power adapter supplied with the MAP-2105. Otherwise,
the product may be damaged.
5. Startup the MAP-2105
To get the first management of the MAP-2105, please follow the following steps.
1. Connect the MAP-2105’s WAN port to the network where can provide the DHCP
services. For example, connect to the LAN port of XRT-401D.
2. Power on a PC that also connects to the LAN port of the XRT-401D with DHCP
or fixed IP address.
3. Open the Internet browser and go to the DHCP status page of XRT-401D to
check the WAN IP address of the MAP-2105.
3
4. Check the MAC address from the Web page and also the MAC address label of
the MAP-2105. For example, 09-64 as the figure above.
5. Key in the IP address you found for MAP-2105 with “https://”. For example:
https://192.168.0.100.
6. The pop-up screen will ask for user name and password. By default, please key
in “admin” for both name and password. Then bring up the screen.
7. Now, the MAP-2105 is ready for services
6. Basic Network Setup
The sample network topology is as below.
Step 1: Gateway Configuration:
[Configuration -> Local Service -> VPN Server]
Enable VPN Server = checked
4
Add New User by pressing Add button
Username: test (it is defined by user)
Password: test (it is defined by user)
Assign IP: 10.16.1.7 (this address must be in the same IP segment as Gateway’s Backhaul radio IP)
Comment: Testing (it is defined by user)
Status: Enable
[Configuration -> Local Service -> Mobile IP]
Enable Transparent Mobile IP Service: checked
Mobile IP Community Name: PLANET (it must be identical for all nodes in the same mesh network)
Mobile Location Register Address: 10.16.1.7 (the IP address assigned in VPN Server screen)
5
Step 2: Reboot the Gateway
Step 3: Relay Configuration:
[Configuration -> Local Service -> Mobile IP]
Enable Transparent Mobile IP Service: checked
Mobile IP Community Name: PLANET (it must be identical for all nodes in the same mesh network)
Mobile Location Register Address: 10.16.1.7 (the IP address assigned in Gateway VPN Server screen)
Step 4: Reboot the Relay
Step 5: MAP-2105 Configuration:
[Configuration -> Local Service -> VPN Client]
Enable PPTP Client: checked
VPN Server: 192.168.0.99 (the Gateway WAN IP address)
Remote Subnet: 10.0.0.0 (the subnet of Gateway’s Backhaul radio IP)
Remote Netmask: 255.0.0.0 (the net mask of Gateway’s Backhaul radio IP)
Username: test (it is identical as defined in Gateway VPN Server screen)
Password: test (it is identical as defined in Gateway VPN Server screen)
Step 6: Reboot the MAP-2105
Step 7: Check MAP-2105 status
6
CN Info
Two correspondent nodes connected with relevant info.
Client Info
Info of the mobile station recorded in the MAP-2105.
Step 8: Check Mobile IP status in Gateway or Relay
Use HTTPS to access the web interface of Gateway or Relay.
[Info -> Status -> Mobile IP]
The information of current connected Mobile IP client is displayed.
7. Further Configuration
For advanced settings of MAP-2105, please refer to the user’s manual in the CD. The CD will including:
• User Guide for Web Management
• Management Utility
• User Guide for Management Utility
If you have any difficulty on resolving the problem while installing or using the device, please feel free to contact your local dealer or PLANET Technical Support.
Part NO.:2010-E10200-000
Loading...