Planet IGS-5227-6T, IGS-5227-6MT, IGS-5227-6MT-X Quick Installation Manual

Industrial IP67-rated 6-Port Gigabit

Managed Ethernet Switch

(-40~75 degrees C)

IGS-5227-6T/IGS-5227-6MT/IGS-5227-6MT-X

Quick Installation Guide

Table of Contents

1. Package Contents ....................................................................................... 3

2. Making Waterproof RJ45 Cable (IGS-5227-6T) .............................................. 4

3. Connecting Waterproof Cable to the IGS-5227-6T ......................................... 7

4. M12 A-coded Connector Pin Assignment ......................................................10

5. M12 (8-pin, A-coded Male) to RJ45 (8-pin) Straight-through UTP Cabling .......11

6. M12 X-coded Connector Pin Assignment ......................................................12

7. M12 (8-pin, X-coded Male) to RJ45 (8-pin) Straight-through UTP Cabling .......13

8. Connecting M12 Cable to the IGS-5227-6MT/IGS-5227-6MT-X .......................14

9. M12 DC Power Cable Pin Assignment .........................................................16

10. Requirements ...........................................................................................17

11. Starting Web Management .........................................................................18

12. Saving Conguration via Web .....................................................................21

13. Recovering Back to Default Conguration .................................................... 22

14. Customer Support .....................................................................................23

1. Package Contents

Thank you for purchasing PLANET Industrial L2+ Managed Ethernet Switch.
“Industrial Managed Switch” is used as an alternative name in this Quick
Installation Guide. Open the box of the Industrial Managed Switch and carefully
unpack it. The box should contain the following items:

z The Industrial Managed Switch

(IGS-5227-6T/IGS-5227-6MT/IGS-5227-6MT-X) x 1

z Quick Installation Guide x 1

z 1.2m M12 Power Cable x 1

z Waterproof RJ45 Connector (IGS-5227-6T only) x 6

z 2m 8-pin A-coded M12-to-RJ45 UTP Cable (IGS-5227-6MT only) x 1

z 2m 8-pin X-coded M12-to-RJ45 UTP Cable (IGS-5227-6MT-X only) x 1

z DIN Rail Kit x 1

z Wall-mount Kit x 1

If any item is found missing or damaged, please contact your local reseller for
replacement.

3

2. Making Waterproof RJ45 Cable (IGS-5227-6T)

Please read the following instructions and follow the procedures in the order being
presented:

Step 1: Take a waterproof RJ45 jack out from the Industrial Managed Switch box

and get hold of one RJ45 cable.

Step 2: Insert the RJ45 cable through the waterproof RJ45 jack.

Step 3: Prepare an RJ45 connector.

4

Step 4: Put the RJ45 connector in place with cable crimper.

The standard RJ45 receptacle/connector

There are 8 wires on a standard UTP/STP cable and each wire is
color-coded. The following shows the pin allocation and colors of
straight-through cable connection:

Note

Straight Cable

112233445566778

SIDE 1

SIDE 1

SIDE 2

8

1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown

SIDE 2

1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown

Please make sure your waterproof RJ45 cables are with same pin
assignment and colors as the above picture before deploying the
cables into your network.

5

Step 5: To lock in the RJ45 connector, pull back the cable till the connector nicely

ts into the waterproof connector hole.

1. Use only the waterproof RJ45 connector provided in the package
of the IGS-5227-6T.

2.If the waterproof RJ45 connector is found missing or damaged,
please contact your local reseller where you purchased from. If
the new waterproof RJ45 connector is obtained from PLANET,
make sure its dimensions are the same.

6

Note

3. Never use any waterproof RJ45 connector that is not purchased
from PLANET or doesn’t have the same dimensions of the IGS­5227-6T; it will damage the device permanently.

3. Connecting Waterproof Cable to the IGS-5227-6T

Follow all the connecting waterproof cable steps as shown in the
example.

Note

Step 1: Turn counterclockwise to remove the waterproof screw nuts of a RJ45

port and power input.

Step 2: Insert the waterproof RJ45 connector into the port of the Industrial

Managed Switch.

7

Step 3: Turn clockwise to tighten the screw nut of the waterproof RJ45 connector.

Step 4: Insert the waterproof M12 power connector into the port of the power

input.

8