Planet IGS-510TF operation manual

1. Package Contents

Thank you for purchasing PLANET industrial compact 5-port Gigabit Ethernet Switch, IGS-500T/IGS-510TF. In the following section, the term “Industrial Gigabit Ethernet Switch” means the IGS-500T or IGS-510TF.

Open the box of the Industrial Gigabit Ethernet Switch and carefully unpack it. The box should contain the following items:

Industrial Gigabit

Ethernet Switch x 1

DIN-rail Kit x 1 RJ45 Dust Caps

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

User’s Manual x 1 Wall-mount Kit x 1

SFP Dust Cap x 1

(IGS-510TF only)

IGS-500T x 5

IGS-510TF x 4

Power Consumption (Ethernet Full

Max. 3.6 watts/12.28BTU

Max. 4.3 watts/14.67BTU

Loading)

Dimensions (W x D x H)

30 x 70 x 104 mm

Weight 252g 270g

Enclosure IP30 metal case

Installation DIN-rail kit and wall-mount kit

ESD Protection 6KV

EFT Protection 6KV

Switch Specications

Switch Architecture

Store-and-Forward

Switch Fabric 10Gbps

Throughput (packet per

7.4Mpps@64bytes

second)

Address Table 4K entries

Buer Memory 1M bits on-chip buer memory

Jumbo Frame 9Kbytes

Flow Control

Back pressure for half duplex IEEE 802.3x pause frame for full duplex

3. Hardware Introduction

3.1 Switch Front Panel

The front Panels of the Industrial Gigabit Ethernet Switches consist of Ethernet interfaces and LED indicators.

 Front View

P1 P2

P1 P2 Fault

ACTLNK

1000

10/

100

1000

10/

100

LNK/

100

ACT

ACTLNK

IGS-510TF

IGS-500T

5 5

Figure 1:

IGS-500T Front View

P1 P2

ACTLNK

1000

10/

100

1000

10/

100

LNK/ ACT

IGS-510TF

Figure 2:

IGS-510TF Front View

1 2 3 4

V1+

V2+

V1-

V2-

DC Input: 9-48V , 0.6A max.

PWR1

PWR2

AC Input: 24V , 0.3A max.

Figure 4: IGS-510TF Top View

3.4 Wiring the Power Inputs

The terminal block connector on the top panel of Industrial Gigabit Ethernet Switch is used for two DC redundant power inputs. Please follow the steps below to insert the power wire.

When performing any of the procedures like inserting the wires or tightening the wire-clamp screws, make

Caution

[IGS-500T]

1. Insert positive and negative DC power wires into contacts 1 and 2 for POWER 1, or contacts 5 and 6 for POWER 2.

sure the power is OFF to prevent from getting an electric shock.

Max. fault loading: 24V, 1A

1 2 3 4 5 6

V1+

PWR1

V2+

PWR2Fault

DC Input: 12-48V AC Input: 24V

, 0.3A max.

, 0.28A max.

- 1 -

2.ProductSpecications

Model IGS-500T IGS-510TF

Hardware Specications

4 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports

1 1000BASE-SX/LX/ BX SFP interface compatible with 100BASE-FX SFP

Removable 4-pin terminal block Pin 1/2 for Power 1; Pin 3/4 for Power 2

9~48V DC, redundant power with reverse polarity protection function, 24V AC power support

Copper Ports

SFP Slot --

Connector

Alarm

Power Requirements

5 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports

Removable 6-pin terminal block Pin 1/2 for Power 1; Pin 3/4 for fault alarm; Pin 5/6 for Power 2

One relay output for power failure. Alarm relay current carry ability: 1A@DC 24V

12~48V DC, redundant power with reverse polarity protection function, 24V AC power support

Standards Conformance

Regulatory Compliance

FCC Part 15 Class A, CE

IEC 60068-2-32 (free fall)

Stability Testing

IEC 60068-2-27 (shock) IEC 60068-2-6 (vibration)

IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet

Standards Compliance

IEEE 802.3ab Gigabit Ethernet IEEE 802.3az Gigabit SX/LX (IGS-510TF only) IEEE 802.3x Full-Duplex Flow Control

IEEE 802.3az Energy Ecient Ethernet (EEE)

IEEE 802.1p Class of Service

Environment

Temperature

Humidity

Operating: -40~75 degrees C Storage: -40~75 degrees C

Operating: 5~90% (non-condensing) Storage: 5~90% (non-condensing)

- 3 -

- 5 -

3.2 LEDDenition:

LED Color Function

P1 Green Lights to indicate power input 1 has power.

P2 Green Lights to indicate power input 2 has power.

Fault Red

Lights to indicate that power 1 or power 2 has failed. (For IGS-500T only)

Lights to indicate the port is running at

1000 LNK/ACT

Green

1000Mbps speed and successfully established.

Blinks to indicate that the Switch is actively sending or receiving data over that port.

Lights to indicate the port is running

100 LNK/ACT

Amber

at 10/100Mbps speed and successfully established.

Blinks to indicate that the Switch is actively sending or receiving data over that port.

3.3 Switch Upper Panel

The upper panels of the Industrial Gigabit Ethernet Switches consist of one terminal block connector within two power input.

Max. fault loading: 24V, 1A

1 2 3 4 5 6

V1+

PWR1

V2+

PWR2Fault

DC Input: 12-48V AC Input: 24V

, 0.3A max.

, 0.28A max.

Figure 3: IGS-500T Top View

- 7 -

2. Tighten the wire-clamp screws for preventing the wires from loosening.

1 2 3 4 5 6

Power 1 Fault Power 2

+ - + -

[IGS-510TF]

1. Insert positive and negative DC power wires into contacts 1 and 2 for POWER 1, or contacts 3 and 4 for POWER 2.

1 2 3 4

V1+

V2+

V1-

V2-

DC Input: 9-48V , 0.6A max.

PWR1

PWR2

2. Tighten the wire-clamp screws for preventing the wires from loosening.

1 2 3 4

Power 1 Power 2

+ - + -

AC Input: 24V , 0.3A max.

- 2 -

- 4 -

- 6 -

- 8 -

Note

Top View

The wire gauge for the terminal block should be in the range between 12 and 24 AWG.

4.1 DIN-rail Mounting Installation

1. The power input range is 12V ~ 48V DC for IGS500T, 9 ~ 48V DC for IGS-510TF and supports 24V

Note

AC.

2. Use one power input when using 24V AC.

3.5 Wiring the Fault Alarm Contact (IGS-500T Only)

The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Gigabit Ethernet Switch will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.

1 2 3 4 5 6

The Fault Alarm Contacts are energized (CLOSE) for normal

Fault Alarm Contacts

Note

Fault

1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 24V DC, 1A.

operation and will OPEN when failure occurs

4.2 Wall-mount Plate Mounting

4.3 Side Wall-mount Plate Mounting (IGS-510TF Only)

You must use the screws supplied with the wallmounting brackets. Damage caused to the parts by

Caution

using incorrect screws would invalidate your warranty.

- 9 -

3.6 Grounding the Device

Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device.

Earth Ground

1 2 3 4

V1+

V2+

V1-

V2-

DC Input: 9-48V , 0.6A max. AC Input: 24V , 0.3A max.

Note

PWR1

PWR2

EMD (Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.

4. Installation

This section guides you to installing the Industrial Gigabit Ethernet Switch on the DIN rail and wall. Please read this chapter completely before continuing.

- 11 -

5. Three-View Diagram

The three-view diagram of the Industrial Gigabit Ethernet Switch consists of multiple auto-sensing 10/100/1000BASE-T RJ45 ports and one removable terminal block. The LED indicators are also located on the front panel.

 IGS-500T

V1+

Max. fault loading: 24V, 1A

PWR1

V2+

PWR2Fault

DC Input: 12-48V

AC Input: 24V

, 0.3A max.

, 0.28A max.

Mounting Kit

9.00

91.00

18.00

28.00

18.00

Mounting Kit

40.00

48.80

40.00

DIN-Rail Kit

Front View

P1 P2 Fault

ACTLNK

1000

100

ACTLNK

IGS-500T

30.00

Bottom View

104.00

70.00

30.00

50.00

Rear ViewSide View Side View

52.00

21.69

28.65

18.00

 IGS-510TF

30.00

50.00

Top View

V1+

PWR1

V1-

V2+

PWR2

V2-

DC Input: 9-48V , 0.6A max.

AC Input: 24V , 0.3A max.

Mounting Kit

9.00

18.00

91.00

28.00

18.00

Mounting Kit

Front View

P1 P2

ACTLNK

1000

10/ 100

1000

10/ 100

LNK/ ACT

IGS-510TF

30.00

Bottom View

Rear ViewSide View Side View

30.16

104.00

70.00

52.00

21.69

28.65

18.00

Figure 6: IGS-510TF Three-View Diagram

40.00

48.80

40.00

Customer Support

Thank you for purchasing PLANET products. You can browse our

online FAQ resource on PLANET web site rst to check if it could

solve your issue. If you need more support information, please contact PLANET switch support team.

PLANET online FAQs: http://www.planet.com.tw/en/support/faq

Switch support team mail address: support@planet.com.tw

DIN-Rail Kit

Unit: mm

Note

This following pictures show how to install the device. However, the device in the picture is not IGS-500T or IGS-510TF.

- 10 -

Figure 5: IGS-500T Three-View Diagram

- 12 - - 13 - - 14 -

Unit: mm

Copyright © PLANET Technology Corp. 2019. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.