Planet IGS-10020PT User Manual

IGS-10020PT

L2+ Industrial 8-Port 10/100/1000T 802.3af PoE + 2-Port 100/1000X SFP Managed Switch with Wide Operating Temperature

Physical Port

• 8 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with

IEEE 802.3af / 802.3at PoE Injector

• 2 100/1000BASE-X mini-GBIC/SFP slots for SFP type auto

detection

–One RJ45 console interface for basic management and

setup

Power over Ethernet

• Complies with IEEE 802.3af / IEEE 802.3at Power over

Ethernet / end-span PSE

• Up to 8 IEEE 802.3af / 802.3at devices powered

Environmentally Hardened Design

PLANET Industrial 8-Port Gigabit 802.3af PoE Switch, IGS-10020PT, is equipped with a

rugged IP30 metal case for stable operation in heavy Industrial demanding environments.

Besides, the IGS-10020PT provides a high level of immunity against electromagnetic

interference and heavy electrical surges which are usually found on plant floors or in

curbside trafc control cabinets. Being able to operate in wide temperature range from -40

to 75 degrees C, the IGS-10020PT can be placed in almost any difcult environment. The

IGS-10020PT, which takes up little space, can be mounted on a DIN rail or wall.

• Supports PoE power up to 30.8 watts for each PoE port

• Auto detects powered device (PD)

• Circuit protection prevents power interference between ports

• Remote power feeding up to 100m

• PoE management features

–IEEE 802.3af and IEEE 802.3at mode switch control

–Total PoE power budget control

–Per port PoE function enable/disable

–PoE admin-mode control

–PoE port power feeding priority

–Per PoE port power limit

–PD classication detection

–Temperature Threshold Control

–PoE Usage Threshold Control

–PD Alive Check

–PoE schedule

Redundant Ring Protocol Suitable for Surveillance System

As the IGS-10020PT supports redundant ring technology, it has the capability of rapid

self-recovery to prevent interruptions and external intrusions. It incorporates advanced

Redundant Ring technology, Spanning Tree Protocol (802.1w RSTP), and redundant

power supply system into customer’s industrial automation network to enhance system

reliability and uptime in harsh factory environments. The IGS-10020PT also protects

customer’s industrial network connectivity with switching recovery capability that is used

for implementing fault tolerant ring and mesh network architectures. If the Industrial

network is interrupted accidentally, the recovery time could be less than 50ms to quickly

bring the network back to normal operation.

Industrial Case & Installation

• IP30 aluminum case protection

• DIN rail and wall-mount design

• 48V DC, redundant power with polarity reverse protect

function

• Supports EFT protection of 6000 VDC for power line

• Supports 6000 VDC Ethernet ESD protection

• -40 to 75 degrees C operating temperature

Digital Input & Digital Output

• 2 Digital Input (DI)

• 2 Digital Output (DO)

• Integrate sensors into auto alarm system

• Transfer alarm to IP network via email and SNMP trap

Built-in Unique PoE Functions for Surveillance Management

Outdoor PoE IP Camera

1000BASE-SX/LX Fiber-optic

1000

PoE

1000BASE-T UTP with PoE

1000

PoE

Recovery time < 20 ms

IGS-10020PT

Network Video Recorder

Traffic Control Center

ERPS Ring for Video Transmission Redundancy

PoE PD Alive-checking

PoE Camera

Ping Request

Checking alive status for 3 times Restart PoE device if without response

PT PoE Camera

No Response!

Step 1 Step 2 Step 3

PoE

OFF

PoE

1000BASE-TX UTP with PoE

6 Watts 6 Watts 12 Watts 12 Watts

Total Consumption: 36 watts / hr

PoE

PoE PoE

PoE

PowerOnPowerOnPowerOnPower

5 PM8 AM

5 PM 8 AM

6 Watts 6 Watts 12 Watts 12 Watts

Save 24 watts / hr during off-business hours

PoE PoE

Total Saved = 10800watts / month

PoE PoE

Power

Off

Power

Off

Power

Off

As a managed PoE Switch for surveillance network, the IGS-10020PT features intelligent

PoE management functions:

■ PD Alive Check

■ Scheduled Power Recycling

■ SMTP/SNMP Trap Event Alert

■ PoE Schedule

Intelligent Alive Check for Powered Device

The IGS-10020PT PoE Switch can be congured to monitor connected PD’s status in real

time via ping action. Once the PD stops working and responding, the IGS-10020PT will

recycle the PoE port power and bring the PD back to work. It also greatly enhances the

reliability to ensure that the PoE port will reset the PD power, thus reducing administrator’s

management burden.

IGS-10020PT

Layer 2 Features

• Prevents packet loss with back pressure (half-duplex) and

IEEE 802.3x pause frame ow control (full-duplex)

• High performance of Store-and-Forward architecture and

runt/CRC ltering eliminates erroneous packets to optimize

the network bandwidth

• Storm Control support

–Broadcast/Multicast/Unicast

• Supports VLAN

–IEEE 802.1Q tagged VLAN

–Up to 255 VLANs groups, out of 4094 VLAN IDs

–Provider Bridging (VLAN Q-in-Q) support (IEEE

802.1ad)

–Private VLAN Edge (PVE)

–Protocol-based VLAN

–MAC-based VLAN

–Voice VLAN

• Supports Spanning Tree Protocol

–IEEE 802.1D Spanning Tree Protocol (STP)

–IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)

–IEEE 802.1s Multiple Spanning Tree Protocol (MSTP),

spanning tree by VLAN

–BPDU Guard

• Supports Link Aggregation

–802.3ad Link Aggregation Control Protocol (LACP)

–Cisco ether-channel (static trunk)

–Maximum 5 trunk groups, up to 8 ports per trunk group

–−Up to 16Gbps bandwidth (duplex mode)

• Provides port mirror (1-to-1)

• Port mirroring to monitor the incoming or outgoing trafc on

a particular port

• Loop protection to avoid broadcast loops

• Supports ERPS (Ethernet Ring Protection Switching)

PoE Schedule for Energy Saving

Under the trend of energy saving worldwide and contributing to environmental protection

on the Earth, the IGS-10020PT can effectively control the power supply besides its

capability of giving high watts power. The built-in “PoE schedule” function helps you to

enable or disable PoE power feeding for each PoE port during specied time intervals and

it is a powerful function to help SMBs or enterprises save power and money.

Layer 3 IP Routing Features

• Supports maximum 32 software static routes and route

summarization

Quality of Service

• Ingress Shaper and Egress Rate Limit per port bandwidth

control

• 8 priority queues on all switch ports

• Trafc classication

–IEEE 802.1p CoS

–IP TOS/DSCP/IP precedence

–IP TCP/UDP port number

–Typical network application

• Strict priority and Weighted Round Robin (WRR) CoS

policies

• Supports QoS and In/Out bandwidth control on each port

IGS-10020PT

I/O

Digital Input and Digital Output for External Alarm

The IGS-10020PT supports Digital Input and Digital Output on its front panel. This external

alarm enables users to use Digital Input to detect and log external device status (such as

door intrusion detector), and send event alarm to the administrators. The Digital Output

could be used to alarm the administrators if the IGS-10020PT port shows link-down, link-up

or power failure.

Digital Input

Enclosure

Door Detector (Door Closed)

Security OK Alarm Warning Alarm Messaging

Enclosure

Door Detector (Door Open)

Mail

System

Log

Digital Output

I/O

DC Power Failure

RJ-45 Cable Link Down

Layer 3 IPv4/IPv6 Software VLAN Routing for Secure and Flexible Management

To help customers stay on top of their businesses, the IGS-10020 series not only provides

ultra high transmission performance and excellent Layer 2 technologies, but also IPv4/IPv6

software VLAN routing feature which allows to crossover different VLANs and different IP

addresses for the purpose of having a highly-secured, flexible management and simpler

networking application.

Robust Layer 2 Features

The IGS-10020PT can be programmed for advanced switch management functions

such as dynamic port link aggregation, Q-in-Q VLAN, private VLAN, Rapid Spanning

Tree Protocol, Layer 2 to Layer 4 QoS, bandwidth control and IGMP snooping. The IGS-

10020PT provides 802.1Q tagged VLAN, and the VLAN groups allowed will be maximally

up to 255. Via aggregation of supporting ports, the IGS-10020PT allows the operation of a

high-speed trunk combining multiple ports. It enables a maximum of up to 5 trunk groups

with 8 ports per trunk group, and supports fail-over as well.

Efﬁcient Management

For efficient management, the IGS-10020PT Managed Ethernet Switch is equipped

with console, Web and SNMP management interfaces. With the built-in Web-based

management interface, the IGS-10020PT offers an easy-to-use, platform-independent

management and configuration facility. For text-based management, the IGS-10020PT

can be accessed via Telnet and the console port. Moreover, it also offers secure remote

management via any standard-based management software by supporting SNMPv3

connection which encrypts the packet content at each session.

I/O

Fiber Cable Link Down

Uplink

SNMP TRAP

• Trafc-policing policies on the switch port

• DSCP remarkin

Multicast

• Supports IGMP snooping v1, v2 and v3

• Supports MLD snooping v1 and v2

• Querier mode support

• IGMP snooping port ltering

• MLD snooping port ltering

• MVR (Multicast VLAN Registration)

Security

• IEEE 802.1x Port-based/MAC-based network access

authentication

• Built-in RADIUS client to cooperate with the RADIUS servers

• TACACS+ login users access authentication

• RADIUS/TACACS+ users access authentication

• IP-based Access Control List (ACL)

• MAC-based Access Control List

• Source MAC/IP address binding

• DHCP snooping to lter distrusted DHCP messages

• Dynamic ARP Inspection discards ARP packets with invalid

MAC address to IP address binding

• IP Source Guard prevents IP spoong attacks

• IP address access management to prevent unauthorized

intruder

Management

• Switch Management Interfaces

–Console/Telnet Command Line Interface

–Web switch management

–SNMP v1 and v2c switch management

–SSH/SSL and SNMP v3 secure access

• Four RMON groups (history, statistics, alarms, and events)

• IPv6 IP address/NTP/DNS management

• Built-in Trivial File Transfer Protocol (TFTP) client

• BOOTP and DHCP for IP address assignment

• Firmware upload/download via HTTP/TFTP

• DHCP Relay

• DHCP Option 82

–User Privilege levels control

–Network Time Protocol (NTP)

–Link Layer Discovery Protocol (LLDP)

–SFP-DDM (Digital Diagnostic Monitor)

–Cable diagnostic technology provides the mechanism to

detect and report potential cabling issues

–Reset button for system reboot or reset to factory

default

–PLANET Smart Discovery Utility for deployment

management

+ 6 hidden pages