Planet IFGS-1022HPT operation manual

Industrial 8-Port 10/100TX 802.3at PoE+

+ 2-Port Gigabit TP/SFP Combo Ethernet Switch

IFGS-1022HPT

User’s Manual

Table of Contents

1. Package Contents ........................................................................................ 3

2. Hardware Introduction ................................................................................. 4

2.1 Physical Dimensions .............................................................................. 4

2.2 Switch Front Panel ................................................................................ 5

2.3 LED Indicators ...................................................................................... 7

2.4 Switch Upper Panel ............................................................................... 8

2.5 Wiring the Power Inputs ........................................................................ 8

2.6 Wiring the Fault Alarm Contact ............................................................... 9

2.7 Product Features ..................................................................................10

2.8 ProductSpecications ...........................................................................11

3. Installation ................................................................................................14

3.1 DIN-rail Mounting Installation ................................................................ 14

3.2 Wall-mount Plate Mounting ...................................................................16

3.3 Installing the SFP Transceiver ................................................................ 17

3.4 Removing the Transceiver Module ..........................................................18

4. Troubleshooting .......................................................................................... 19

APPENDIX A: Networking Connection ................................................................20

A.1 PoE RJ45 Port Pin Assignments (End-span) .............................................20

A.2 Switch’s RJ45 Pin Assignments ..............................................................20

A.3 RJ45 Cable Pin Assignments ..................................................................21

A.4 Fiber Optic Cable Connection Parameter .................................................22

APPENDIX B: Approved PLANET SFP Transceivers ..............................................23

1. Package Contents

Thank you for purchasing PLANET industrial 8-Port 10/100TX 802.3at PoE+ + 2-Port
Gigabit TP/SFP combo Ethernet Switch, IFGS-1022HPT. In the following section, the
term “Industrial PoE+ Switch” means the IFGS-1022HPT.

Open the box of the Industrial PoE+ Switch and carefully unpack it. The box
should contain the following items:

Industrial PoE+ Switch x 1 User’s Manual x 1

DIN Rail Kit x 1 Wall-mount Kit x 1

If any of these are missing or damaged, please contact your dealer immediately;
if possible, retain the carton including the original packing material, and use them
again to repack the product in case there is a need to return it to us for repair.

3

2. Hardware Introduction

2.1 Physical Dimensions

 Dimensions (W x D x H): 161 x 107 x 72mm

Front View

DIP ON

1

Long Reach Mode

2

3

4 5 6 7 8

Standard

Extended

P1 P2 FAULT

9 10

7

5

3

1

802.3at PoE+

LNK
1000

109

8

6

4

LNK

2

PoE In-Use

IFGS-1022HPT

Side View

Top View

ACT

1A@24V

DC1 DC2

Input DC 48V~56V

Fault

Side View

ACT

Bottom View

Dimensions ( unit = mm )

4

2.2 Switch Front Panel

The front panel of the Industrial PoE+ Switch consists of 8 10/100/BASE-TX ports
featuring 30-watt 802.3at PoE+, and 2 additional Gigabit copper/SFP combo
interfaces for Gigabit Ethernet extension and video uplink. The LED indicators are
also located on the front panel of the Industrial PoE+ Switch.

Figure 2-1 shows the front panel of Industrial PoE+ Switch.

DIP ON

1

Long Reach Mode

2

3

4 5 6 7 8

Standard

Extended

P1 P2 FAULT

9 10

ACT

LNK
1000

109

7

5

3

1

802.3at PoE+

8

6

4

LNK

ACT

2

PoE In-Use

IFGS-1022HPT

Figure 2-1: IFGS-1022HPT Front Panel

 Fast Ethernet TP interfaces (Port 1 to port 8)

10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.

 Gigabit TP Interfaces (Port 9 to port 10 TP/SFP Combo Interfaces)

10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters.

 Gigabit SFP Slots (Port 9 to port 10 TP/SFP Combo Interfaces)

1000BASE-SX/LX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver

module:From550meters(multi-modeber)to10/20/30/40/50/60/70/120 kilo­meters(single-modeber).

5

 DIP Switch

P1 P2 FAULT

Extended

Standard

Long Reach Mode

1

2

3

4 5 6 7 8

DIP ON

P1 P2 FAULT

Extended

Standard

Long Reach Mode

1

2

3

4 5 6 7 8

DIP ON

The Industrial PoE+ Switch has a built-in solid DIP switch that provides
“Standard” and “Extend” operation modes. The Industrial PoE+ Switch operates
as a normal IEEE 802.af/at PoE+ Switch in the “Standard” operation mode.

In the “Extend” operation mode, the Industrial PoE+ Switch operates on a per­port basis at 10Mbps full duplex operation but can support 30-watt PoE power
output over a distance of up to 250 meters overcoming the 100m limit on Ethernet
UTP cable. With this brand-new feature, the Industrial PoE+ Switch provides an
additional solution for 802.3af/at PoE+ distance extension.

Default PoE Mode

PoE

100 meters (328 feet)

Extended PoE Mode

PoE

250 meters (820 feet)

PoE IP

Camera

PoE

PoE IP

Camera

100BASE-TX UTP with PoE

6

2.3 LED Indicators

System

LED Color Function

P1 Green Lit: indicates power 1 has power.

P2 Green Lit: indicates power 2 has power.

FAULT Red Lit: indicates neither power 1 or power 2 has no power.

Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1 to Port 8)

LED Color Function

Lit: indicates the link through that port is successfully

LNK/

ACT

PoE

In-Use

Per 10/100/1000BASE-T Interface (Shared with Port 9 to Port 10)

LED Color Function

LNK/

ACT

1000 Orange

Green

Orange

Green

established at 10Mbps or 100Mbps.

Blinking: indicates that the switch is actively sending or

receiving data over that port.

Lit: indicates the port is providing DC in-line power.
Off: indicates the connected device is not a PoE powered device

(PD).

Lit: indicates the link through that port is successfully

established at 10/100/1000Mbps.

Blinking: indicates that the switch is actively sending or

receiving data over that port.

Lit: indicates the link through that port is successfully

established at 1000Mbps.

Off: indicates the link through that port is successfully

established at 10/100Mbps.

Per 1000X SFP Slot (Shared with Port 9 to Port 10)

LED Color Function

Lit: indicates the link through that port is successfully

LNK/

ACT

1000 Orange

Green

established at 1000Mbps.

Blinking: indicates that the switch is actively sending or

receiving data over that port.

Lit: indicates the link through that port is successfully

established at 1000Mbps.

Off: indicates the link through that port is not established.

7

2.4 Switch Upper Panel

The upper panel of the Industrial PoE+ Switch consists of one terminal block
connector within two DC power inputs.

Figure 2-2 shows the upper panel of the Industrial PoE+ Switch.

1A@24V

1 2 3 4 5 6

DC1 DC2

Fault

Input DC 48V~56 V

Figure 2-2: Industrial PoE+ Switch Upper Panel

2.5 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Industrial PoE+ Switch
is used for two DC redundant power inputs. Please follow the steps below to insert
the power wire.

When performing any of the procedures like inserting the wires or
tightening the wire-clamp screws, make sure the power is OFF to
prevent from getting an electric shock.

1. Insert positive and negative DC power wires into contacts 1 and 2 for POWER 1,
or 5 and 6 for POWER 2.

1A@24V

1 2 3 4 5 6

DC1 DC2

Fault

Input DC 48V~56 V

8

2. Tighten the wire-clamp screws for preventing the wires from loosening.

1 2 3 4 5 6

Power 1 Fault Power 2

+ - + -

1. The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.

Note

2. The DC power input range is 48V ~ 56V DC.

2.6 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block connector as the
picture shows below. Inserting the wires, the Industrial PoE+ Switch will detect
the fault status of the power failure and then forms an open circuit. The following
illustration shows an application example for wiring the fault alarm contacts.

Note

The Fault Alarm Contacts are
energized (CLOSE) for normal

Fault Alarm Contacts

Fault

operation and will OPEN when
failure occurs

Insert the wires into the fault alarm contacts

1. The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 30V, max. 3A currents.

9

2.7 Product Features

 Physical Port

 Eight 10/100BASE-TX Fast Ethernet RJ45 ports with IEEE 802.3at/af

PoE+ Injector (Port-1 to Port-8)

 Two 10/100/1000BASE-T Gigabit Ethernet RJ45 ports (Port-9 and Port-10)

 Two 1000BASE-X mini-GBIC/SFP slots for SFP type auto detection (Port-9

and Port-10)

 Power over Ethernet

 Complies with IEEE 802.3at Power over Ethernet Plus, end-span PSE

 Backward compatible with IEEE 802.3af Power over Ethernet

 Up to 8 ports of IEEE 802.3af/802.3at devices powered

 240-watt PoE budget

 Supports PoE power up to 30 watts for each PoE port

 Auto detects powered device (PD)

 Circuit protection prevents power interference between ports

 Remote power feeding up to 100 meters

 Industrial Case and Installation

 IP30 metal case

 DIN rail and wall-mount design

 48~56V DC, redundant power with polarity reverse protect function

 Supports 6000V DC Ethernet ESD protection

 -40 to 75 degrees C operating temperature

 Switching

 Hardware-based 10/100Mbps (half/full duplex), 1000Mbps (full duplex), auto-

negotiation and auto MDI/MDI-X

 Features Store-and-Forward mode with wire-speed ltering and forwarding

rates

 IEEE 802.3x ow control for full duplex operation and back pressure for half

duplex operation

 16K MAC address table size

 10K jumbo frame

 IEEE 802.1Q VLAN transparency

 Hardware DIP switch for “Standard” and “Extend” mode selection; the

“Extend” mode features 30-watt PoE transmit distance of 250m at speed of
10Mbps

 Automatic address learning and address aging

 Supports CSMA/CD protocol

10

2.8 ProductSpecications

Product IFGS-1022HPT

HardwareSpecications

Fast Ethernet Copper Ports

Gigabit Ethernet Copper Ports

SFP/mini-GBIC Slots

PoE Injector Port

Switch Architecture Store-and-Forward

Switch Fabric 5.6Gbps/non-blocking

Switch Throughput@64 bytes 4.1Mpps @64 bytes

MAC Address Table 16K entries

Shared Data Buffer 4Mb SRAM

Flow Control

Jumbo Frame 10 Kbytes

DIP Switch (Port 1 to port 8)

Eight 10/100BASE-TX RJ45 auto-MDI/MDI-X ports
(Port-1 to Port-8)

Two 10/100/1000BASE-T RJ45 auto-MDI/MDI-X
ports (shared with Port-9 and Port-10)

Two 1000BASE-SX/LX/BX SFP interfaces (shared
with Port-9 and Port-10)

Eight ports with 802.3af/802.3at PoE+ injector
function (Port-1 to Port-8)

IEEE 802.3x pause frame for full-duplex. Back
pressure for half-duplex

Standard mode: 30-watt PoE transmit distance of
100m at speed of 10/100Mbps
Extend mode: 30-watt PoE transmit distance of
250m at speed of 10Mbps

LED

3 x LED for System and Power:
 Green: DC Power 1
 Green: DC Power 2
 Red: Power Fault Alarm
2 x LED for PoE Copper Port (Port-1~Port-8):
 Green: LNK/ACT (10/100Mbps)
 Orange: PoE-In-Use
2 x LED for 10/100/1000T Copper Port
(Port-9~Port-10):
 Green: LNK/ACT
 Orange: 1000
2 x LED for per mini-GBIC interface
(Port-9~Port-10)
 Green: LNK/ACT
 Orange: 1000

11

Removable 6-pin terminal block

Connector

Alarm

Power Requirements

Power Consumption/
Dissipation

Dimensions (W x D x H) 72 x 107 x 161 mm

Weight 1034g

ESD Protection 6KV DC

Enclosure IP30 aluminum case

Installation DIN-rail kit and wall-mount kit

Power over Ethernet

PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE

PoE Power Supply Type End-span

Power Pin Assignment 1/2(+), 3/6(-)

PoE Power Output

PoE Power Budget

Max. Number of Class 2 PDs 8

Max. Number of Class 3 PDs 8

Max. Number of Class 4 PDs 8

Standards Conformance

Regulatory Compliance FCC Part 15 Class A, CE

 Pin 1/2 for Power 1
 Pin 3/4 for power fault alarm
 Pin 5/6 for Power 2

One relay output for power failure.
Alarm relay current carry ability: 1A @ 24V AC

48~56V DC, 5.5A (max.)
(>51V DC for PoE+ output recommended)

19 watts, 64BTU (Standby without PoE function)
at DC 56V power input
23 watts, 78BTU (Full loading without PoE
function) at DC 56V power input
244 watts, 832BTU (Full loading with PoE function)
at DC 56V power input

IEEE 802.3af Standard

- Per port 48V~51V DC (depending on the power
supply), max. 15.4 watts
IEEE 802.3at Standard

- Per port 51V~56V DC (depending on the power
supply), max. 30 watts

Dual power input: maximum 240W (depending on
power input)

12

IEC 60068-2-32 (free fall)

Stability Testing

Standards Compliance

Environment

Operating Temperature -40 ~ 75 degrees C

Storage Temperature -40 ~ 85 degrees C

Humidity 5 ~ 95% (non-condensing)

IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)

IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000BASE-T
IEEE 802.3z Gigabit SX/LX
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus

13

3. Installation

This section describes the functionalities of the Industrial PoE+ Switch’s
components and guides how to install it on the DIN-rail and wall. Basic knowledge
of networking is assumed. Please read this chapter completely before continuing.

This following picture is telling the user how to install the device,

Note

3.1 DIN-rail Mounting Installation

The DIN-rail is screwed on the Industrial PoE+ Switch when out of factory. When
replacing the wall-mount application with DIN-rail application, Industrial PoE+

Switchis needed. Pleaserefer to thefollowing gures toscrew the DIN-railon the

Industrial PoE+ Switch. To hang the Industrial PoE+ Switch, follow the following
steps:

Step 1: Screw the DIN-rail on the Industrial PoE+ Switch.

and the device is not IFGS-1022HPT.

14

Step 2: Lightly insert the bottom of the switch into the track.

1

2

Step 3: Make sure if the DIN-rail is tightly secured on the track.

Step 4: Please refer to the following procedures to remove the Industrial PoE+

Switch from the track.

1

2

Step 5: Lightly pull out the bottom of the switch for removing it from the track.

15

3.2 Wall-mount Plate Mounting

To install the Industrial PoE+ Switch on the wall, please follow the instructions
described below.

Step 1: To remove the DIN-Rail from the Industrial PoE+ Switch, loosen the

screws to remove the DIN-rail.

Step 2: Place the wall mount plate on the rear panel of the Industrial PoE+

Switch.

Step 3: Use the screws to screw the wall mount plate on the Industrial PoE+

Switch.

Step 4: Use the hook holes at the corners of the wall mount plate to hang the

Industrial PoE+ Switch on the wall.

Step 5: To remove the wall mount plate, reverse the steps above.

16

3.3 Installing the SFP Transceiver

The sections describe how to insert an SFP transceiver into an SFP slot.

The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and
out the transceiver to/from any SFP port without having to power down the
Industrial PoE+ Switch as Figure 2-3 shows.

MGB Series
Transceiver

Figure 2-3: Plug-in the SFP Transceiver

PLANET Industrial PoE+ Switch supports 1000Mbps mode with both single mode
and multi-mode SFP transceivers.

1. Before we connect Industrial PoE+ Switch to the other network device, we have
to make sure both sides of the SFP transceivers are with the same media type,
for example, 1000BASE-SX to 1000BASE-SX, 1000BASE-LX to 1000BASE-LX.

2.Check whether the ber-optic cable type matches with the SFP transceiver

requirement.

 To connect to 1000BASE-SX SFP transceiver, please use the multi-mode

bercablewithonesidebeingthemaleduplexLCconnector type.

 To connect to 1000BASE-LX or 1000BASE-BX SFP transceiver, please

use the single-mode ber cable with one side being the male duplex LC
connector type.

 Connect the Fiber Cable

1. Insert the duplex LC connector into the SFP transceiver.

2. Connect the other end of the cable to a device with SFP transceiver installed.

3. Check the LNK/ACT LED of the SFP slot on the front of the Industrial PoE+
Switch. Ensure that the SFP transceiver is operating correctly.

17

4. Check the Link mode of the SFP port if the link fails.

It is recommended to use PLANET SFPs on the Industrial PoE+
Switch. If you insert an SFP transceiver that is not supported, the

Note

Industrial PoE+ Switch will not recognize it.

3.4 Removing the Transceiver Module

1. Make sure there is no network activity by consulting or checking with the
network administrator. Or through the management interface of the switch/
converter (if available) to disable the port in advance.

2. Remove the Fiber Optic Cable gently.

3. Turn the lever of the MGB series module to a horizontal position.

4. Pull out the module gently through the lever.

MGB Series
Transceiver

18

Note

Figure 2-4: Pull Out from the Transceiver

Never pull out the module without pulling the lever or the push
bolts on the module. Directly pulling out the module with force
could damage the module and the SFP module slot of the Industrial
PoE+ Switch.

4. Troubleshooting

This chapter contains information to help you solve issues. If the Industrial PoE+
Switch is not functioning properly, make sure the Industrial PoE+ Switch was set
up according to instructions in this manual.

Q1: The per port LED is not lit

Solution:

Check the cable connection of the Industrial PoE+ Switch.

Q2 :Per port LED is lit, but the trafc is irregular

Solution:

Check whether the attached device is not set to dedicated full duplex. Some
devices use a physical or software switch to change duplex modes. Auto­negotiation may not recognize this type of full-duplex setting.

Q3: Why the Industrial POE+ Switch doesn’t connect to the network

Solution:

Check each port LED on the Industrial PoE+ Switch. Try another port on the
Industrial PoE+ Switch. Make sure the cable is installed properly and the right
type. Turn off the power. After a while, turn on the power again.

Q4: Can I install MGB-SX or other non wide temperature SFP module into

SFP slot of Industrial PoE+ Switch?

Solution:

Yes, you can. However, the MGB-SX and the other non wide temperature SFP
module cannot operate under -40 to 75 degrees C.

19

APPENDIX A: Networking Connection

A.1 PoE RJ45 Port Pin Assignments (End-span)

PIN NO RJ45 POWER ASSIGNMENT

1 2 3 4 5 6 7 8

A.2 Switch’s RJ45 Pin Assignments

1000Mbps, 1000BASE-T

Contact MDI MDI-X

1 BI_DA+ BI_DB+

2 BI_DA- BI_DB-

3 BI_DB+ BI_DA+

4 BI_DC+ BI_DD+

5 BI_DC- BI_DD-

6 BI_DB- BI_DA-

7 BI_DD+ BI_DC+

8 BI_DD- BI_DC-

1 Power +

2 Power +

3 Power -

6 Power -

10/100Mbps, 10/100BASE-TX

RJ45 Connector Pin Assignment

Contact

1 Tx + (transmit) Rx + (receive)

2 Tx - (transmit) Rx - (receive)

3 Rx + (receive) Tx + (transmit)

4, 5 Not used

6 Rx - (receive) Tx - (transmit)

7, 8 Not used

Media Dependent Interface

MDI

Media Dependent Interface - Cross

20

MDI-X

A.3 RJ45 Cable Pin Assignments

The standard RJ45 receptacle/connector

There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The
following shows the pin allocation and color of straight-through cable and crossover
cable connection:

Straight Cable

12345678

12345678

Crossover Cable

12345678

12345678

SIDE 1

SIDE 2

SIDE 1

SIDE 2

SIDE 1

1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown

SIDE 1 SIDE 2

1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown

SIDE 2

1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown

1 = White/Green
2 = Green
3 = White/Orange
4 = Blue
5 = White/Blue
6 = Orange
7 = White/Brown
8 = Brown

Figure A-1: Straight-through and Crossover Cable

Please make sure your connected cables are with the same pin assignment and
color as the above picture before deploying the cables into your network.

21

A.4 Fiber Optic Cable Connection Parameter

The wiring details are shown below:

1000X Fiber Optic Cables:

Standard Fiber Type CableSpecications

1000BASE-SX
(850nm)

1000BASE-LX
(1300nm)

Wiring Distances:

Standard Fiber

1000BASE- SX MM

1000BASE- LX

Multi-mode 50/125μmor62.5/125μm

Multi-mode 50/125μmor62.5/125μm

Single-mode 9/125μm

Diameter

(micron)

62.5

62.5
50
50

62.5

MM

SM 9 N/A 5000*

50
50

Modal Bandwidth

(MHz * km)

100
200
400
500

5
4
5

Max. Distance

(meters)

220
275
500
550

550

22

APPENDIX B: Approved PLANET SFP Transceivers

The following list of approved PLANET SFP transceivers is correct at the time of
publication:

Gigabit SFP Transceiver Modules

MGB-GT SFP-Port 1000BASE-T Module - 100m

MGB-SX SFP-Port 1000BASE-SX mini-GBIC module - 550m

MGB-SX2 SFP-Port 1000BASE-SX mini-GBIC module – 2km

MGB-LX SFP-Port 1000BASE-LX mini-GBIC module - 10km

MGB-L30 SFP-Port 1000BASE-LX mini-GBIC module - 30km

MGB-L50 SFP-Port 1000BASE-LX mini-GBIC module - 50km

MGB-L70 SFP-Port 1000BASE-LX mini-GBIC module - 70km

MGB-L120 SFP-Port 1000BASE-LX mini-GBIC module - 120km

MGB-LA10

MGB-LB10

MGB-LA20

MGB-LB20

MGB-LA40

MGB-LB40

MGB-LA60

MGB-LB60

MGB-TSX SFP-Port 1000BASE-SX mini-GBIC module - 550m (-40~75°C)

MGB-TLX SFP-Port 1000BASE-LX mini-GBIC module - 10km (-40~75°C)

MGB-TL30 SFP-Port 1000BASE-LX mini-GBIC module - 30km (-40~75°C)

SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module ­10km

SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module ­10km

SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module –
20km

SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module ­20km

SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module ­40km

SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module ­40km

SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module ­60km

SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module ­60km

23

MGB-TL70 SFP-Port 1000BASE-LX mini-GBIC module - 70km (-40~75°C)

MGB-TLA10

MGB-TLB10

MGB-TLA20

MGB-TLB20

MGB-TLA40

MGB-TLB40

MGB-TLA60

MGB-TLB60

SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module ­10km (-40~75°C)

SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module ­10km (-40~75°C)

SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module –
20km (-40~75°C)

SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module ­20km (-40~75°C)

SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module ­40km (-40~75°C)

SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module ­40km (-40~75°C)

SFP-Port 1000BASE-LX (WDM, TX:1310nm) mini-GBIC module ­60km (-40~75°C)

SFP-Port 1000BASE-LX (WDM, TX:1550nm) mini-GBIC module ­60km (-40~75°C)

24