Planet IDL-4802, IDL-4802-48 Quick Installation Manual

Download

Page 1

48-Port ADSL 2/2+ IP DSLAM

IDL-4802 / IDL-4802-48

Quick Installation Guide

Page 2

Table of Contents

Package Contents ............................................................................................ 3

Overview ........................................................................................................ 4

Safety Instruction ............................................................................................ 6

Hardware Installation ....................................................................................... 7

1. Power and Ground Connections ................................................................ 7

2. FAN Cable Connection ............................................................................. 9

3. ADSL and POTS Connections ................................................................... 9

4. Uplink Interfaces Connections .................................................................10

5. Management Port Connection .................................................................11

6. Console Port Connection .........................................................................11

7. Housekeeping Connection .......................................................................11

WEB Conguration ..........................................................................................13

Further information .........................................................................................19

Page 3

Package Contents

Note

IDL-4802

¢ IDL-4802 Unit x 1

¢ AC Power Cord x 1

¢ CD x 1

¢ Quick Installation Guide x 1

¢ 2-Meter Telco-50 Cable x 4

¢ Console Cable x 1

¢ Rack-mounting Ear x 2

¢ Screw Package x 2

¢ Connect Tenon x 4

¢ RJ-45 Cable for Fan x 1

IDL-4802-48

¢ IDL-4802-48Unit x 1

¢ DC Power Terminal Block x 1

¢ CD x 1

¢ Quick Installation Guide x 1

¢ 2-Meter Telco-50 Cable x 4

¢ Console Cable x 1

¢ Rack-mounting Ear x 2

¢ Screw Package x 2

¢ Connect Tenon x 4

¢ RJ-45 Cable for Fan x 1

If any of above items are damaged or missing, please contact your dealer immediately.

Using a power supply with a different voltage rating will damage and void the warranty for this product.

Page 4

Overview

Front Panel

The front panels are shown below.

IDL-4802

IDL-4802-48

Interface Denition

Interface Description

POWER Power On / Off switch.

-48V

FAN

Console

RST A hidden reset button for hardware resetting.

ACO Alarm Cut Off

MGMT

Uplink 1 & 2 Gigabit Ethernet electrical trunk ports.

SFP 1 & 2 Gigabit Ethernet SFP trunk ports.

PHONE 1 & 2 RJ-21 connector for connecting POTS lines.

LINE 1 & 2 RJ-21 connector for connecting DSL lines.

-48V DC Power plug-in. (*IDL-4802-48)

RJ-45 port for connection with the RJ-45 port on the front panel of fan card to provide power to the fan.

RJ-50 port for housekeeping inputs and one alarm contact output.

RS-232 port for system conguration and maintenance. (9600,

8, N, 1)

Ethernet Port connected to LAN for providing system out-band Telnet control interface, such as system monitor, control or software upgrade.

Page 5

LED Denition

LED Color Description

Uplink Port connect with 100/1000Mbps Ethernet link

Orange

Uplink

Green

SYS

ALM

DSL status Green

Green Normal Operation

Red Self-test fail

Green Normal Operation

Red To indicate the system alarm status

Off Uplink Port connect with 10Mbps Ethernet link

On Active

Off Inactive

Flash Uplink Port Transmit / receive data

On ADSL Port is activated and linked

Off ADSL Port is Disabled

Flash ADSL Port is activated but not linked

Rear Panel

The rear panels are shown below.

IDL-4802

IDL-4802-48

Port Denition

Port Description

AC PWR

AC Power cord plug-in, 100 - 240VAC is allowed. (*IDL-4802)

Page 6

Safety Instruction

The following is the safety instructions for IP DSLAM before installing.

>> The maximum operating temperature of the IP DSLAM is 65ºC. Care must be

taken to allow sufcient air circulation or space between units when the IP DSLAM

is installed inside a closed rack assembly and racks should safely support the combined weight of all IP DSLAM.

>> The connections and equipment that supply power to the IP DSLAM should be capable of operating safely with the maximum power requirements of the IP DSLAM. In the event of a power overload, the supply circuits and supply wiring should not become hazardous.

>> The AC power cord must plug into the right supply voltage. Make sure that the supplied AC voltage is correct and stable. If the input AC voltage is over 10% lower than the standard may cause the IP DSLAM to malfunction.

>> Generally, when installed after the nal conguration, the product must comply

with the applicable safety standards and regulatory requirements of the country in which it is installed. If necessary, consult for technical support.

>> A rare condition can create a voltage potential between the earth grounds of two or more buildings. If products installed in separate building are interconnected,

the voltage potential can cause a hazardous condition. Consult a qualied electrical

consultant to determine whether or not this phenomenon exists and, if necessary, implement corrective action before interconnecting the products. If the equipment is to be used with telecommunications circuit, take the following precautions:

- Never install telephone wiring during a lightning storm.

- Never install telephone jacks in wet location unless the jack is specially designed for wet location.

- Never touch un-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

- Caution when installing or modifying telephone lines (other than a cordless tele phone) during an electrical storm. There is a remote risk of electric shock from lightning.

- Do not use a telephone or other equipment connected to telephone lines to report a gas leak in the vicinity of the leak.

Page 7

Hardware Installation

STANDARD

FRONT MOUNT

FRONT

MOUNTING

BRACKET

MOUNTING

BRACKET

The PLANET IDL-4802 is a 1.5U high box-type IP DSLAM with rack-mountable enclosure. It can be installed in a standard 19-inch rack by using the mounting brackets provided. Mount the shelf on the rack using the large screws provided.

The procedures to connect and wire the system are as follows,

1. Power and Ground Connections

Power Connections

With IDL-4802, connect the AC power cord to the AC supply socket on the rear

panel as below gure, and plug the cord into the external power source. The

voltage must be 100 to 240V AC.

With IDL-4802-48, the DC power interface is a 4-pin terminal block with polarity

signs on the front panel as below gure.

It can be powered from two –48V DC power supply. The DC power connector is a 4P terminal block; 2P is for accommodating one DC power input and other 2P is for accommodating another DC power input. The DC power should be connected to a well-fused power supply.

After completing chassis installation, please apply power to the fused power distribution panel feeding the chassis. When using a DC voltmeter, please check for proper voltage: -60V ~ -36V DC, and make sure that the polarity is correct.

Page 8

Ground Connections

Note

¢InCentralOfce:

There should be a CO GND that is adequately grounded. If the measured resistance

from the grounding screw (on the rear panel of the DSLAM, refer to below gure)

to CO GND is less than 5 Ohm, then it can be assumed that the system is well grounded. If the measured resistance is larger than 5 Ohm, it is recommended to connect the grounding screw to CO GND using #14 or #12 AWG wire gauge conductor.

¢InRemoteCabinet:

The IDL-4802 should be grounded by connecting a #14 or #12 AWG conductor between the grounding screw (on the rear panel of the DSLAM, refer to below

gure) and the earth ground or main grounding bar. The resistance between the

chassis and the grounding bar should be less than 25 Ohm.

Grounding Screw of IDL-4802

Grounding Screw of IDL-4802-48

Ensure that all power sources to the device are turned off during the installation.

Page 9

2. FAN Cable Connection

1 2 3 4 5 6 7 8

Note

There are two FAN ports on the front panel. One is on the FAN card; the other is beside the HK port. To make the fans work, you must use an RJ45-to-RJ45 connector cable to connect the two FAN ports.

FANPortRJ-45pinassignment:

3 , 4 5 6 7 8

GND

FAN

ERR1

FAN

ERR2

FAN

ERR3

FAN

Status

3. ADSL and POTS Connections

The IDL-4802 supports 48 ports ADSL subscribers per box. There are four RJ-21 50-pin female connectors on the front panel of the system. Two for ADSL lines and two for POTS interfaces.

To connect the subscriber lines, use cables with the RJ-21 50-pin male connectors. When installing, just plug the end of cable with connector into the LINE and PHONE connectors on the front panel. The other end of the cable is generally tied to the MDF (Main Distribution Frame).

The MDF Patch panel is optional of standard package.

Page 10

Please plug-in the RJ-21 cable with connector tenon as below gures.

4. Uplink Interfaces Connections

The system provides two types of trunk interfaces (two ports for each type). There are electrical (RJ-45) and optical (SFP) interfaces. When both electrical and optical ports are connected, system will automatically select the interface according to the

priority setting (Fiber rst or Copper rst).

SFP(Mini-GBIC):

Prepare a proper SFP module and install it into the optical trunk port. Then you can

connect ber optics cabling that uses LC connectors or SC connectors (with the use of an optional SC-to-LC adapter) to the ber optics connector on the trunk port.

Page 11

5. Management Port Connection

The IDL-4802 provides one RJ45 (MGMT) on the front panel for Ethernet interface connection. To connect the Ethernet interface to PC directly, an Ethernet crossover cable is required.

6. Console Port Connection

The Console interface on the front panel is the main control interface of the IDL-

4802. To connect the host PC to the console port, a RJ45 (male) connector-to-

RS232 DB9 (female) connector cable is required. The RJ45 connector of the cable is connected to the COM port of the DSLAM; the DB9 connector of the cable is connected to the PC COM port.

7. Housekeeping Connection

The IDL-4802 equips with a RJ-50 port (HK) on the front panel to provide four housekeeping inputs and one alarm contact output. Generally, housekeeping contacts can connect to environment-sensor-controlled switch to indicate the operation environment condition.

Page 12

The HK circuit contains a photo coupler powered by the IDL-4802 to detect the "open" or "close" status of the loop between HK_IN and HK_COM (users don’t need to feed 3.3v power into the circuit). As to the alarm output, there is a relay between ALMOUT and ALMCOM to control the status of the loop to be "OPEN" or "CLOSE" to the alarm equipment (close between ALMOUT and ALMCOM for alarm; open if no alarm).

HKPortRJ-50pinassignment:

OperationdiagramofHousekeepingInputsandAlarmContactOutput:

Page 13

WEB Conguration

This section describes how to use Web Conguration Tool to maintain your IP DSLAM. The IDL-4802 contains a HTTP server. You can login and congure it by

using your Web Browser.

Preparation

Before attempting to congure the IDL-4802, please ensure as below:

Set your computer’s IP with the same network segment of the IP DSLAM.

(Forexample:IDL-4802defaultMGMTIPis192.168.1.1/255.255.255.0)

Then you can set computer’s IP to:

192.168.1.x/255.255.255.0.

(The range for x is from 2 to 253)

Step 1: Using your WEB Browser

Open web browser and type http://192.168.1.1 in the browser’s address box. This IP is the default MGMT IP address of IDL-4802. Press Enter.

Page 14

Step 2: Login the IDL-4802

A login page will appear. Please type your username / password and click "Sign in". (The default username/passwordisadmin/admin)

After you login the IDL-4802, you will see the system information as below.

Page 15

Step 3: Congure the DSL PVC

Go to "Bridge Ë Interface Setup Ë ADSL PVC" setting screen, select the ADSL port and click “Create” to apply the PVC settings.

(For example, create PVC-1 to Port 1. The default VPI/VCIis0/35)

You can see the Port has been created.

Page 16

Step 4: Enable the ADSL Port Service

Go to "System Ë ADSL Port Service" setting screen, select the ADSL port and Admin is "ON". Click "Modify" to make this Port is ON.

You can see the Admin status became to ON.

Page 17

Step 5: Connect the ADSL2/2+ CPE to Patch Panel

Connect the ADSL2/2+ CPE to Patch Panel and congure it, the VPI / VCI value

must be the same with IDL-4802.

After nish setting, the CPE will establish the ADSL connection with IDL-4802. You can check the connection status as below gure. The Current Status is ON.

Now the clients can access to Internet through IDL-4802.

Page 18