PLANET ICS-2100 User Manual
1. Package Contents
Note
Note
Note
Note
Thank you for purchasing PLANET Industrial RS-232 / RS422 / RS-485 over 10/100Base-TX/100Base-FX Media
Converter – ICS-210x series. Terms of “Industrial Serial
Converter” means the products mentioned titled in the
cover page of this Quick Installation Guide.
The PLANET Industrial Serial Converter comes with one of
the following models.
● ICS-2100: Industrial RS-232/RS-422/RS-485 over
10/100Base-TX Media Converter (Copper, RJ-45)
● ICS-2102: Industrial RS-232/RS-422/RS-485 over
100Base-FX Media Converter (Fiber, MM/2km)
● ICS-2102S15: Industrial RS-232/RS-422/RS-485 over
100Base-FX Media Converter (Fiber, SM/15km)
Open the box of the Industrial Serial Converter and carefully
unpack it. The box should contain the following items:
Check the contents of your package for following parts:
° Industrial Serial Converter x1
° CD-ROM User's Manual x1
° Quick Installation Guide x1
° Wall Mount Kit x 1
° DIN-Rail Kit x1
2. Tighten the wire-clamp screws for preventing the wires
from loosing. Figure 2 shows PWR1 and PWR2 pin of the
terminal block.
1 2 3 4 5 6
Power 1 Fault Power 2
- + - +
Figure 2 PWR1 & PWR2 pin of terminal block.
The wire gauge for the terminal block should be
in the range between 12 ~ 24 AWG.
4. Start Web Management
The PLANET Industrial Serial Converter provides a built-in
browser interface. You can manage the ICS-210x remotely
by having a remote host with web browser, such as
Microsoft Internet Explorer, Netscape Navigator or Mozilla
Firefox.
Using this management method:
The ICS-210x must have an Internet Protocol (IP) address
accessible for the remote host.
Figure 3 Web Management over Ethernet
Before you start congure the ICS-210x, please note the
ICS-210x is congured through an Ethernet connection,
make sure the manager PC must be set on same the IP
subnet address.
For example, the default IP address of the ICS-210x is
192.168.0.100, then the manager PC should be set at
192.168.0.x (where x is a number between 1 and 254,
except 100), and the default subnet mask is 255.255.255.0.
Figure 5 Web Main screen
Now, you can use the Web management interface to
continue the Industrial Serial Converter management,
please refer to the user manual for more.
1. For security reason, please change and
memorize the new password after this first
setup.
2. Only accept command in lowercase letter
under web interface.
- 1 -
If any of these are missing or damaged, please contact your
dealer immediately, if possible, retain the carton including
the original packing material, and use them against to
repack the product in case there is a need to return it to us
for repair.
2. Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial Serial Converter is used for two DC redundant
powers input. Please follow the steps below to insert the
power wire.
1. Insert positive / negative DC power wires into the
contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2.
Figure 1 shows PWR1 and PWR2 of the Industrial Serial
Converter.
- 3 -
3. Requirements
¢ Network cables.
For ICS-2100: Use standard network (UTP) cables with
RJ-45 connector.
For ICS-2102 / ICS-2102S15: Use Multi-mode or Single-
modeberpatchcordwithSCconnector.
¢ Subscriber PC installed with Ethernet NIC (Network Card)
¢ Workstations of subscribers running Windows 98/ME,
NT4.0, 2000/2003/XP, MAC OS X or later, Linux, UNIX or
other platform compatible with TCP/IP protocols.
¢ Above PC installed with WEB Browser, such as Microsoft
Internet Explore or Mozilla Firefox
It is recommended to use Internet Explore 6.0
or above to access Industrial Serial Converter.
- 5 -
1. Use Internet Explorer 6.0 or above Web browser. Enter
IP address http://192.168.0.100 (the factory-default
IP address) to access the Web interface.
2. When the following login screen appears, please enter
the default username and password (default user name
and password is "admin"). Press Login to enter the
main screen of ICS-210x. The login screen in Figure 4
appears.
Default IP Address: 192.168.0.100
Default Account: admin
Default Password: admin
- 7 -
5. IP Address be changed or forgotten
admin password
To reset the IP address to the default IP Address
“192.168.0.100” and the password to factory default mode
(default user name and password is admin). Press the
hardware reset button at the front panel about 10 seconds.
After the device is rebooted, you can login the management
Web interface within the same subnet of 192.168.0.xx and
default use name / password.
Hardware Reset Button
V1- V1+ V2- V2+
Figure 1 PWR1 & PWR2 of Industrial Serial Converter.
- 2 -
- 4 -
Figure 4 Login screen
After entering the password (default user name and
password is “admin”) in login screen (Figure 4 appears).
The Web main screen appears as Figure 5.
- 6 -
Figure 6 Reset button
The ICS-2100 Reset button location is the same
with ICS-2102 and ICS-2102S15.
- 8 -
6. Customer Support
Thank you for purchase PLANET products. You can browse
our online FAQ resource at the PLANET Web site rst to
check if it could solve you issue. If you need more support
information, please contact PLANET Media Converter support
team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=3
Media Converter support team mail address:
support_converter@planet.com.tw
Copyright © PLANET Technology Corp. 2009.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology
Corp. All other trademarks belong to their respective
owners.
- 9 -
- 11 -
- 10 -
- 12 - - 13 - - 14 -
Loading...