PLANET ICA-HM351 User Manual

User’s Manual

ICA-HM351

2 Mega-Pixel 35M IR Outdoor Box PoE IP Camera

Copyright © 2011 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mecha nical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor , or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Federal Communication Commission Interference St atement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

To assure continued compliance. (example-use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must accept any interference received, including interference that may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for a n uncontrolled enviro nment . In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment

CE Mark Warning

This is a Class B product. In a domestic environment, this product may ca use radio interfere nce, in which case the user may be required to take adequate measures.

WEEE Regulation

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

User’s Manual for PLANET 2 Mega-Pixel 35M IR Outdoor Box PoE IP Camera Model: ICA-HM351 Rev: 1.0 (August. 2011) Part No. EM-ICAHM351

Table of Content

U1.U UIntroductionU ............................................................................................................... 6

U1.1 OverviewU............................................................................................................. 6

U1.2 FeaturesU.............................................................................................................. 6

U1.3U UPackage ContentsU ............................................................................................7

U2. Basic SetupU .................................................................................................................. 8

U2.1 System RequirementsU ...................................................................................... 8

U2.2 Physical DescriptionU ......................................................................................... 9

U2.2.1 Identification of ICA-HM351 cableU ...................................................... 9

U2.3 Hardware InstallationU ...................................................................................... 11

U2.3.1 Physical InstallationU ............................................................................. 11

U2.4 Initial Utility InstallationU ................................................................................... 12

U2.5 PreparationU....................................................................................................... 14

U2.5.1 Search and View by PLANET IPWizardU...........................................14

U2.6U UUsing UPnP of Windows XP, Vista or Win7U................................................ 16

U2.6.1 Windows XPU ......................................................................................... 16

U2.6.2 Windows VistaU ...................................................................................... 21

U2.6.3 Windows 7U ............................................................................................ 22

U2.7U UInstall the Device behind a NAT RouterU ...................................................... 23

U2.8U USetup ActiveX to use the Internet CameraU ................................................. 24

U2.8.1 Internet Explorer 6 for Windows XPU.................................................. 24

U2.8.2 Internet Explorer 7 for Windows XPU.................................................. 25

U,QWHUQHW([SORUHUIRU:LQGRZV9LVWDDQG:LQU............................ 2

U3U UWeb-based ManagementU ..................................................................................... 27

U3.1 IntroductionU ...................................................................................................... 27

U3.2 Connecting to Internet CameraU..................................................................... 27

U3.3 Live ViewU .......................................................................................................... 29

U3.4 ActiveX ControlU ................................................................................................ 32

U3.4.1 Digital ZoomU.......................................................................................... 32

U3.4.2 RecordU ................................................................................................... 33

U3.4.3 SnapshotU ............................................................................................... 33

U3.4.4 VoiceU ......................................................................................................34

U3.4.5 StatisticsU ................................................................................................34

U3.4.6 AboutU ...................................................................................................... 35

U3.5 System SettingU ................................................................................................ 36

U3.5.1 NetworkU ................................................................................................. 37

U3.5.2 HTTPSU ................................................................................................... 39

U3.5.3 DDNS serverU ........................................................................................ 40

U3.5.4 PPPoEU ................................................................................................... 41

U3.5.5 StreamingU .............................................................................................. 42

U3.5.6 UPnPU...................................................................................................... 44

U3.5.7 BonjourU .................................................................................................. 45

U3.5.8 OnvifU....................................................................................................... 46

U3.5.9 IP FilterU .................................................................................................. 47

U3.5.10 IP NotificationU ..................................................................................... 48

U3.6 Camera ConfigurationU .................................................................................... 50

U3.6.1 PictureU.................................................................................................... 50

U3.6.2 Privacy MaskU ........................................................................................ 52

U3.6.3 PTZ SettingU ........................................................................................... 53

U3.6.4 Preset SettingU ....................................................................................... 54

U3.6.5 Tour SettingU ........................................................................................... 54

U3.7 SystemU .............................................................................................................. 56

U3.7.1 SystemU................................................................................................... 56

U3.7.2 Date & TimeU .......................................................................................... 57

U3.7.3 MaintenanceU ......................................................................................... 58

U3.8 VideoU ................................................................................................................. 60

U3.8.1 CommonU ................................................................................................ 60

U3.8.2 Video ProfileU .........................................................................................61

U3.8.3 ROIU ......................................................................................................... 62

U3.9 Audio ConfigurationU ........................................................................................ 63

U3.10 User Privilege Access ConfigurationU.......................................................... 64

U3.11 E-Mail ConfigurationU ..................................................................................... 65

U3.12 Object DetectionU............................................................................................ 66

U3.13 Event Server ConfigurationU ......................................................................... 67

U3.13.1 FTP ServerU ......................................................................................... 67

U3.13.2 TCP ServerU ......................................................................................... 68

U3.13.3 HTTP ServerU....................................................................................... 69

U3.13.4 SAMBA ServerU ................................................................................... 70

U3.14 Event Schedule ConfigurationU .................................................................... 71

U3.15 Record ConfigurationU ................................................................................... 75

UAppendix A: Alarm I/O ConnectorU ............................................................................... 76

UAppendix B: PING IP AddressU ..................................................................................... 78

UAppendix C: 3GPP AccessU........................................................................................... 79

UAppendix D: Bandwidth and Video Size EstimationU ................................................. 80

UAppendix E: DDNS ApplicationU....................................................................................81

UAppendix F: Configure Port Forwarding ManuallyU.................................................... 86

UAppendix G: Troubleshooting & Frequently Asked QuestionsU................................ 89

UAppendix H: Product SpecificationU.............................................................................. 94

1. 0BIntroduction

Thank you for purchasing the 2 Mega-Pixel series IP Camera, the ICA-HM351 bring users high resolution surveillance both at day and night in outdoor. The ICA-HM351, the 2 Mega-Pixel (1920 x 1080) 35 meters IR Outdoor PoE IP Camera, supports the highest video compression – H.264, which provides small video size and save you lots of bandwidth usage. The new video compression is the best solution for Internet video transmission. The ICA-HM351 supports Multi-Profile Streaming function to generate H.264, MPEG-4 and M-JPEG streaming simultaneously to differentiate users in different resolutions and frame rates. This state-of-the-art design is considerable to fit in various network environments.

The ICA-HM351 provides 2-Way audio function for surveillance. It can remotely talk to anyone at the ICA-HM351 site with additional speaker connected to the camera. Via two ICA-HM351, users can easily communicate to each other for surveillan ce control. The ICA-HM351 Compliant with IEEE 802.3af PoE standard can be located in any place where there is no power outlet available. Through Power over Ethernet, the installers are fearless for the power b reakd own at the remote site because the network devices can be powered from the central station where UPS is installed.

The ICA-HM351 infrared Internet camera performs reliable operation in any environment. With the Aluminum rugged all-weather housing enclosure, the ICA_HM351 maintains the reliable operation in any environment. Moreover, it has built-in fan and heater to prevent the machine overheated or sub cooling.

The ICA-HM351 follows the ONVIF v1.01 and v1.02 standard SDK for users to integrate with the third party software. The ICA-HM351 can also work with PLANET Cam Viewer 3 Lite / Pro Management software and Network Video Recorder products for video surveillance application and provides monitoring, recording and event management functions to secure your property and life.

11B1.1 Overview

This user’s guide explains how to operate this camera from a computer. User should read this manual completely and carefully before you operate the device

12B1.2 Features

• H.264, MPEG4 and MJPEG simultaneously (Tri-encoders)

• High Quality FullHD 1080p Resolution

• Built-in IR LED and visible distance up to 35 meters

• IR-Cut filter brings better video quality in the daytime and nighttime

• Compliant with IEEE 802.3af PoE interface

• 2-Way audio supported with external speaker an d microphone

• Support 3GPP for iPhone and Android phone for remote view

• DDNS, PPPoE and FTP uploading offers more alternatives in surveillance network

• 10 Motion Detection feature can monitor any suspicious movement in a specific area

• Easy configuration and management via Windows-Based utility or web browser

• Supports ONVIF v1.0 and v1.02 / v1.01 Standard

• Industrial design with -30 to 60 Degree C operating temperature

13B1.3 Package Contents

User can find the following items in the package:

ICA-HM351 x 1 Power Adapter x 2 Wall Mounting Kit x 1 User’s Manual CD x 1 Quick Installation Guide x 1

NOTE:

1. If any of the above items are missing, please contact your dealer immediately.

2. Using the power supply that is not the one included in Internet camera packet will cause damage and void the warranty for this product.

1B2. Basic Setup

This chapter provides details of installing and configuring the internet camera

14B2.1 System Requirements

CPU RAM

Video RAM

Display Resolution

Operating System

DirectX

Network

Intel Dual Core 2.0GHz or higher

2GB

(above Recommended)

128MB 1024 x 768 24bits Windows XP / Vista / Win7

9.0c above Wired Ethernet 100Base-TX

(above Recommended )

or above

NOTE:

The listed information is minimum system requirements only. Actual requirement will vary depending on the nature of your environment.

15B2.2 Physical Description

37B2.2.1 Identification of ICA-HM351 cable

Interface Description

DC Power

(Power Jack, IR and IP

Camera)

RJ-45

(LAN socket, PoE, IR and

IP Camera )

The input power is DC 12V, 1A. Note：ONLY use package power adapter supplied with the

internet. Otherwise, the product may be damaged. Connect to PC or Hub/Switch.

For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built auto-negotiation protocol can detect or negotiate the transmission speed of the network automatically. Please use CAT-5 cable to connect the Network Camera to a 100Mbps Fast Ethernet network switch or hub.

LAN LED (green color)

This LED will be flashing while network accessing via Ethernet.

Power LED (orange color)

This LED is used to indicate whether DC power is on or not. In addition, this LED will be flashing while the wireless accessing of the Camera.

Note：ONLY use one power source, either from DC or from

802.3af Power over Ethernet.

Audio Output

(Green, Line Out)

Microphone Input

(Pink, Audio In)

Video Output

(BNC)

Reset

(Factory Default)

DI/DO, RS-485

DC Power

(Power Jack, Fan and

Heater)

Connect a loud speaker to the IP Camera. This is for voice alerting and two-way audio.

Connect a microphone to the IP Camera. The Network Camera also provides composite video output.

The video output function is only for easy installation to check view angle and focus. Furthermore, only “720p Mode” supports this function.

This button is used to restore the all factory default settings. Sometimes restarting the device will make the system back to a normal state. However, if the system still got problems after restart, user can restore the factory default settings and install it again.

Restore the device:

Note: Restoring the factory default setting will lose the all

previous settings included IP address forever. User needs to run the IPWizard program to search the device and configure it to let the device work properly again.

Connect RS-485 to external scanner and connect to sensor in and alarm out devices.

The input power is DC 12V, 1A for Fan and Heater. Note：That supplies the power to the built-in heater with the

power adapter included in package.

Terminal block for I/O connectors:

Name Cable Color Function

12VDC Brown/White DC 12V (50mA maximum) GND Blue/White GND D+ Purple/White RS485 data + D- Gray RS485 data - DI Green/White Digital signal input DO Orange/White Digital signal output

a.) Press the button down continuously. b.) Hold the button at least 5 seconds and release it.

Then the device has been restored to default settings and reboot again.

16B2.3 Hardware Installation

38B2.3.1 Physical Installation

1. Fix IR camera to desired location with wall mount fixture

2. Plug-in Ethernet Cable into RJ-45 connector

Connect an Ethernet cable to the LAN socket located on the Network Camera’s back panel

and attach it to the network.

NOTE:

If there has an IEEE 802.3af PoE switch in your network, you can connect the camera LAN cable to this PoE switch to obtain power. The power adapter is unnecessary when internet camera is connected to a PoE switch.

3. Connect RS485 D+ and D- (if you need to control PT scanner)

4. Attach the power supply

Connect the attached power adapters to camera and heater and plug-in these adapters into

power outlet

NOTE:

1. Only use the power adapter supplied with internet camera. Otherwise, the product

may be damaged.

2. The power adapter is unnecessary when internet camera is connected to a PoE

switch. Otherwise, the product may be damaged when internet camera is connected to a PoE switch and power adapter simultaneously.

5. Atta ch BNC connector (option)

Connect the video BNC connector to a monitor set if necessary check camera viewing angle and focus.

6 Attach Speaker to camera (option)

If user needs not only video stream but also audio stream, then the speaker should be attached to camera.

7. Done

17B2.4 Initial Utility Installation

This chapter shows how to quick set up your IP camera. The camera is with the default settings. However to help you find the networked camera quickly the windows utility PLANET IPWizard can search the cameras in the network that shall help you to configure some basic setting before you started advanced management and monitoring.

1. Insert the bundled CD into the CD-ROM drive to launch the auto-run program. Once completed, a welcome menu screen will appear.

2. Click the “IPWizard II” hyperlink; you will see the dialog box as below.

NOTE:

If the welcome screen does not appear, click “Start” at the taskbar. Then, select “Run” and type “D:\Utility\IPWizard II\setup.exe”, assume D is your CD-ROM drive.

3. The “Welcome to the InstallShield Wizard for PLANET IPWizard II” prompt will display on the screen and click “Next” to continue.

4. Please click “Next” to install with original settings, or you may click “Change…” button to modify the install folder then press “Next” to continue.

5. Please click “Install” to start the installation.

6. Please click “Finish” to complete the installation and launch program immediately.

18B2.5 Preparation

When you installed the camera on a LAN environment, you may execute PLANET IPWizard to discover camera’s IP address and set up related parameters in the camera.

39B2.5.1 Search and View by PLANET IPWizard

When you installed the Camera on a LAN environment, you have two easy ways to search your Cameras by PLANET IPWizard II or UPnP discovery. Here is the way to execute PLANET IPWizard II to discover Camera’s IP address and set up related parameter in a Camera.

When launch the PLANET IPWizard II, a searching window will pop up. PLANET IPWizard II is starting to search Network Cameras on the LAN. The existed devices will be listed as below.

View

If PLANET IPWizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly. Furthermore you could double click the left button of mouse to link to the network device by browser.

2.5.2 Configure Network by PLANET IPWizard

In case you want to change the IP related parameters of wired interface, please select the device you want to configure and click the LAN button. Relative settings will be carried out as below.

You could modify the relative settings of the selected device. Click “<<” button will quit the LAN setting procedure and click “>>” button will move to next page as below.

In case, you do not want to change username and/or password, then just click “Submit” button to perform your setting accordingly. Click “<<” button will go back to previous page. If you like to change username and/or password of the device, just click the check button. Then, the related fields will show up as below.

After keying in new username and password, click “Submit” button to perform your setting accordingly. Click “<<” button will go back to previous page.

2.6 19BUsing UPnP of Windows XP, Vista or Win7

40B2.6.1 Windows XP

UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP enabled device. If the operating system, Windows XP, of your PC is UPnP enabled, the device will be very easy to configure. Use the following steps to enable UPnP settings only if your operating system of PC is running Windows XP.

NOTE:

Windows 2000 does not support UPnP feature.

Go to Start > Settings, and Click Control Panel

The “Control Panel” will display on the screen and double click “Add or Remove Programs” to

continue

The “Add or Remove Programs” will display on the screen and click Add/Remove Widows Components to continue.

The following screen will appear, select “Networking Services” and click “Details” to continue

The “Networking Services” will display on the screen, select “Universal Plug and Play” and click

“OK” to continue.

Please click “Next” to continue

The program will start installing the UPnP automatically. You will see the below pop-up screen,

please wait while Setup configures the components.

Please click “Finish” to complete the UPnP installation

Double-click “My Network Places” on the desktop, the “My Network Places” will display on the screen and double-click the UPnP icon with Internet camera to view your device in an internet browser.

41B2.6.2 Windows Vista

UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP enabled device. If the operating system, Windows Vista, of your PC is UPnP enabled, the device will be very easy to configure. Use the following steps to enable UPnP settings only if your operating system of PC is running Windows Vista.

Go to Start > Control Panel > Network and Internet > Network and Sharing Center, and turn on “Network Discovery”.

Double-click “My Network Places“ on the desktop, the “My Network Places” will display on the

screen and double-click the UPnP icon with Internet camera to view your device in an internet browser.

42B2.6.3 Windows 7

Go to Start > Control Panel > Network and Internet > Network and Sharing Center, if network discovery is off; click the arrow button Click Turn on network disco very, and then click Apply .

to expand the section.

If you are prompted for an administrator

password or confirmation, type the password or provide confirmation.

2.7 20BInstall the Device behind a NAT Router

Once installed, the device is accessible on your LAN. To access the device from the Internet you must configure your broadband router to allow incoming data traffic to the device. If the device is installed on the LAN with a router, then it may get a dynamic IP address from the DHCP server. However, if the device wants to be accessed from the WAN, its IP address needs to be setup as fixed IP, also the port forwarding or Virtual Server function of router needs to be setup.

However, if your NAT router supports UPnP feature, it can be very easy to achieve NAT traversal automatically. To do this, enable the NAT-traversal feature, which will attempt to automatically configure the router to allow access to the camera.

Installing the device with an UPnP router on your network is an easy 3–step procedure:

(1) Enable UPnP option of your NAT router　 (2) Enable UPnP NAT traversal option of 　 the Network Camera (default) (3) Access your Network Camera by DIPS　

(1) Enable UPnP option of your NAT router

To use UPnP IGD function (NAT traversal), you need to make sure the UPnP function is enabled in your router. Most new home routers should support this function. Some of routers are default enable and others are not. Please check user’s manual of your NAT router for detail.

(2) Enable UPnP NAT traversal option of the Network Camera

Refer to Setting Î Network Î UPnP page for detail NAT traversal setting. Note that this option is default enabled.

(3) Access your Network Camera by DIPS

Refer to Setting Î System Î System page for detail DIPS information

2.8 21BSetup ActiveX to use the Internet Camera

The Internet camera web pages communicate with the Internet camera using an ActiveX control. The ActiveX control must be downloaded from the Internet camera and installed on your PC. Your Internet Explorer security settings must allow for the web page to work correctly. To use the Internet camera, user must setup his IE browser as follows:

43B2.8.1 Internet Explorer 6 for Windows XP

From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î”Custom Level…”, please setup your “Settings” as follow.

Set the first 3 items

• Download the signed A ctiveX co ntrols

• Download the unsigned ActiveX controls

• Initialize and script the ActiveX controls not masked as safe to Prompt

By now, you have finished your entire PC configuration for Internet camera.

44B2.8.2 Internet Explorer 7 for Windows XP

From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î”Custom Level…”, please setup your “Settings” as follow.

Set the first 3 items

• Allow previously unused ActiveX control to run…

• Allows Script lets

• Automatic prompting for ActiveX controls

By now, you have finished your entire PC configuration for Internet camera.

2.8.3 Internet Explorer 7 for Windows Vista and Win7

From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Internet” Î”Custom Level…”, please setup your “Settings” as follow.

• Enable “Automatic prompting for ActiveX controls”

• Prompt “Initialize and script active controls not marked….”

From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Trusted Sites” Î”Custom Level…”, please setup your “Settings” as follow.

• Enable “Automatic prompting for ActiveX controls”

• Prompt “Initialize and script active controls not marked….”

By now, you have finished your entire PC configuration for Internet camera.

3 2BWeb-based Management

This chapter provides setup details of the Internet camera’s Web-based Interface.

22B3.1 Introduction

The internet camera can be configured with your Web Browser. Before configure, please make sure your PC is under the same IP segment with Internet camera.

23B3.2 Connecting to Internet Camera

z Use the following procedure to establish a connection from your PC to the camera. z Once connected, you can add the camera to your Browser’s Favorites or Bookmarks.

Start the web browser on the computer and type the IP address of the camera. The Default IP: “

HUhttp://192.168.0.20UH “

The login window of Internet camera will appear, Default login username/password is: admin/ <no password>

;

NOTE:

If the User name and Password have been changed with PLANET IPWizard II, please enter the new User name and Password here.

Web browser may display the “Security Warming” window, select “Yes” to install and run the ActiveX control into your PC.

After the ActiveX control was installed and run, the first image will be displayed.

NOTE:

If you log in the camera as an ordinary user, setting function will be not available. If you log in the camera as the administrator, you can perform all the settings provided within the device.

24B3.3 Live View

Start-up screen will be as follow no matter an ordinary users or an administrator.

Video Profile

ctiveX Control

Streaming Protocol

Monitor Image

Language

Setting Menu

Client Menu

Section

PTZ Control

2-Way Audio

Monitor Image Section The image shot by the camera is shown here. The date and

time are displayed at the top of the window.

Video Profile The camera support multi-profile for three compressions H264,

MEPG-4 and M-JPEG simultaneously. User can chose the proper and/or preferred profile here.

Full Screen Click this button to display the image in full-screen mode (uses

every available space to display the image captured by this camera).

2-Way Audio The Internet camera supports 2-way audio function. User can

chose to enable or disable this function by toggling the icon below

: Disable audio uploading function.

Full Screen

: Enable audio uploading function.

ActiveX Control The plug-in ActiveX control supports a lot of functions by

clicking the left mouse button. Note that this feature only supports on the ActiveX control within Microsoft® Internet Explorer.

Setting Menu This function is detail setting for the camera that only available

for user logged into camera as administrator.

Item Action

Network

Configure Network settings such as Wireless, DHCP, DDNS, 3GPP, PPPoE and UPnP.

Camera Adjust camera parameters.

System

Video

Configure system information, date & time, maintenance, and view system log file.

Configure bit rate and frame rate of video profiles.

Audio Configure audio parameters.

User Setup user name, password and login privilege.

E-Mail Setup E-Mail configuration.

FTP

Object

Detection

This devise is a client site and configure information to upload images to server.

Setup Object detection.

Event

Schedule

Configure the schedule while event triggered.

Streaming Protocol User can select proper streaming protocol according to

networking environment.

Language The device could provide multiple languages to meet

customer’s requirement.

Video Information Display video information including video format, resolution,

frame rate and bit rate.

Client Setting Click this button to display the client extra control panel for

2-way Audio and Full Screen.

PTZ Control Click to display the following control panel:

Camera Direction

Preset

Hide PTZ Control

Camera Speed

Go Tour

Tour

uto Pan

Hide PTZ Control Click the icon will hide the PTZ control function.

Camera Direction Control camera up/down/left/right and home position.

Camera Speed Choose the speed of Pan and Tilt.

Preset Add/Update the preset positions or go to one of these positions.

Tour Select one of the camera tours. Camera tour is comprised by series of

preset locations.

Go Tour Execute the selected camera tour.

Auto Pan Execute the auto pan of camera. While auto pan is running, the

camera will swing the camera automatically. Note that the speed of auto pan is fixed and cannot be adjustable.

NOTE:

If you want to use the PTZ function, it must be connected an external PTZ via RS485 interface. The PTZ function can be enabled. If not then the PTZ function is disabled.

25B3.4 ActiveX Control

The plug-in ActiveX control supports a lot of functions by clicking the left mouse button. Note that this feature only supports on the ActiveX control within Microsoft® Internet Explorer.

On the ActiveX control icon, click the Left Mouse Button, then a menu pop-up. This menu provides features that are unique to the ActiveX control. These features include:

• Record,

• Snapshot,

• Voice,

• Statistics,

• About

45B3.4.1 Digital Zoom

Click Digital Zoom to active this function as above. User can drag or scale the box over the video to adjust zoom ratio and position.

46B3.4.2 Record

Click Record to activate this function. Press Record button to start recording. The video file is saved as ASF format into your local PC. While you want to stop it, press Stop to stop recording. Select Browser, the pop-up window to select the save path and file name prefix, select OK to continue.

After stop recording, list the files, this file is named as Video_yyyymmddhhmmss.asf The ASF files can be display by the standard Windows Media Player, but it needs the DixectX 9.0

or later version to be installed.

NOTE:

Default save path is “C:\Documents and Settings\All user\Desktop

47B3.4.3 Snapshot

Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is saved as JPEG format into your local PC. Select Browser, the pop-up window to select the save path and file name prefix, select OK to continue.

If you like to retrieve the saved image, select the file to display the saved image by using any one of graph editing tools.

NOTE:

Default save path is “C:\Documents and Settings\All user\Desktop

48B3.4.4 Voice

Click Volume to activate this function. These have two control bars for speaker and microphone volume. Scroll this control bar to adjust the audio attribute. Check the volume mute will mute the speaker output.

49B3.4.5 Statistics

Click Statistics to activate this function. A window will be popup to show the statistics information of the streaming status.

NOTE:

That this information is the statistics between the device and your local PC.

50B3.4.6 About

Click About to show the ActiveX information

26B3.5 System Setting

Use this menu to configure the network to connect the device and the clients. This function is only available for user logged into Camera as administrator. Click on each menu name to display its setting page.

Item Action

Network Configure Network settings such as DHCP, DDNS, 3GPP, PPPoE and

UPnP.

Camera Adjust camera parameters, position, and set camera tour.

System Configure system information, date & time, maintenance, and view

system log file.

Video Configure bit rate and frame rate of video profiles.

Audio Configure audio parameters.

User Setup user name, password and login privilege.

E-Mail Setup E-Mail configuration.

Object Detection Setup Object detection.

Event Server Setup FTP/TCP/HTTP server for event.

Event Schedule Configure the schedule while event triggered.

51B3.5.1 Network

This section provides the menu of connecting the device through Ethernet cable.

MAC address Display the Ethernet MAC address of the device. Note that user cannot

change it.

Obtain an IP address automatically (DHCP)

Enable this checked box when a DHCP server is installed on the network to issue IP address assignment. With this setting, the IP address is assigned automatically. If this device cannot get an IP address within limited tries, the device will assign a default IP address for 192.168.0.20.

If you do not select “Obtain an IP address automatically”, then you need to enter these network parameters by yourself.

IP Address This address is a unique numbers that identifies a computer or device

on the WAN or LAN. These numbers are usually shown in groups separated by periods, for example: 192.168.0.200

Subnet Mask Subnets allow network traffic between hosts to be separated based on

the network's configuration. In IP networking, traffic takes the form of packets. IP subnets advance network security and performance to some level by organizing hosts into logical groups. Subnet masks contain four bytes and usually appear in the same "dotted decimal" data. For example, a very common subnet mask in its binary

demonstration 11111111 11111111 11111111 00000000 will usually be shown in the corresponding, more readable form as 255.255.255.0.

Gateway A gateway is a piece of software or hardware that passes information

between networks. You'll see this term most often when you either log in to an Internet site or when you're transient email between different servers.

Obtain DNS from DHCP

Enable this checked box when a DHCP server is installed on the network and provide DNS service.

Primary DNS When you send email or position a browser to an Internet domain such

as xxxxx.com, the domain name system translates the names into IP addresses. The term refers to two things: the conventions for naming hosts and the way the names are control across the Internet.

Secondary DNS The same function as DNS1. It is option not necessary

HTTP Port The device supports two HTTP ports. The first one is default port 80

and this port is fixed. This port is very useful for Intranet usage. The second HTTP port is changeable. Users could assign the second port number of http protocol, and the WAN users should follow the port number to login. If the http port is not assigned as 80, users have to add the port number in back of IP address. For example:

Uhttp://192.168.0.20:8080U.

Therefore, the user can access the device by either

Uhttp://xx.xx.xx.xx/U, or Uhttp://xx.xx.xx.xx:xxxx/ Uto access the device.

If multiple devices are installed on the LAN and also required to be accessed from the WAN, then the HTTP Port can be assigned as the virtual server port mapping to support multiple devices.

NOTE When the configuration is finish, please click “OK” to save and enable

the setting.

52B3.5.2 HTTPS

HTTPS: Stands for Hypertext Transfer Protocol Secure HTTPS is a combination of the

encrypted communication and secure identification of a network are often used for sensitive transactions in corporate information systems. The main idea of HTTPS is to create a secure channel over an insecure network. This ensures reasonable protection from

HeavesdroppersH and Hman-in-the-middle attacksH, provided that adequate cipher

suites are used and that the server certificate is verified and trusted.

HHypertext Transfer ProtocolH with the HSSL/TLSH protocol to provide

Hweb serverH. HTTPS connections

HTTPS To enable or disable the HTTPS service here. Note that the HTTPS

function of this device is not only encrypted the web content but also audio/video data.

Port Choose the HTTPS port. The default value is 443.

53B3.5.3 DDNS server

DDNS: Stands for Dynamic Domain Name Server The device supports DDNS If your device is connected to xDSL directly, you might need this

feature. However, if your device is behind a NAT router, you will not need to enable this feature. Because DDNS allows the device to use an easier way to remember naming format rather than an IP address. The name of the domain is like the name of a person, and the IP address is like his phone number. On the Internet we have IP numbers for each host (computer, server, router, and so on), and we replace these IP numbers to easy remember names, which are organized into the domain name. As to xDSL environment, most of the users will use dynamic IP addresses. If users want to set up a web or a FTP server, then the Dynamic Domain Name Server is necessary. For more DDNS configuration, please consult your dealer.

Your Internet Service Provider (ISP) provides you at least one IP address which you use to connect to the Internet. The address you get may be static, meaning it never changes, or dyn amic, meaning it’s likely to change periodically. Just how often it changes, depends on your ISP. A dynamic IP address complicates remote access since you may not know what your current WAN IP address is when you want to access your network over the Internet. The solution to the dynamic IP address problem comes in the form of a dynamic DNS service.

The Internet uses DNS servers to lookup domain names and translates them into IP addresses. Domain names are just easy to remember aliases for IP addresses. A dynamic DNS service is unique because it provides a means of updating your IP address so that your listing will remain current when your IP address changes. There are several excellent DDNS services available on the Internet and best of all they’re free to use. One such service you can use is www.DynDNS.org. You’ll need to register with the service and set up the domain name of your choice to begi n using it. Please refer to the home page of the service for detailed instructions or refer to Appendix E for more information.

DDNS To enable or disable the DDNS service here.

Server name Choose the built-in DDNS server.

DDNS Host The domain name is applied of this device.

User Name The user name is used to log into DDNS.

Password The password is used to log into DDNS.

54B3.5.4 PPPoE

PPPoE: Stands for Point to Point Protocol over Ethernet A standard builds on Ethernet and Point-to-Point network protocol. It allows Internet camera

connects to Internet wi th xDSL or cable c onnection; it can dial up your ISP and get a dynamic IP address. For more PPPoE and Internet configuration, please consult your ISP.

It can directly connect to the xDSL, however, it should be setup on a LAN environment to program the PPPoE information first, and then connect to the xDSL modem. Power on again, then the device will dial on to the ISP connect to the WAN through the xDSL modem.

The procedures are

• Connect to a LAN by DHCP or Fixed IP

• Access the device, enter Setting Î Network Î PPPoE as below

PPPoE To enable or disable the PPPoE service here.

User Name Type the user name for the PPPoE service which is provided by

ISP.

Password Type the password for the PPPoE service which is provided by

ISP.

IP Address / Subnet

Shows the IP information got from PPPoE server site.

Mask / Gateway

Status Shows the Status of PPPoE connection.

55B3.5.5 Streaming

RTSP is a streaming control protocol, and a starting point for negotiating transports such as RTP, multicast and Unicast, and for negotiating codecs. RTSP can be considered a "remote control" for controlling the media stream delivered by a media server. RTSP servers typically use RTP as the protocol for the actual transport of audio/video data.

RTSP Port Choose the RTSP port. The RTSP protocol allows a connecting client to

start a video stream. Enter the RTSP port number to use. The default value is 554.

RTP Port Specify the range of tran smissi on port nu mber of video stream. Th e default

range is 50000 to 50999. User can specify a number between 1024 and

65535.

NOTE 1. To use the 3GPP function, in addition to previous section, you might

need more information or configuration to make this function work.

2. The camera must be set as Multi-profile mode, not Mega-pixel mode. Otherwise this device cannot serve 3GPP stream.

3. To use the 3GPP function, it strongly recommends installing the Networked Device with a public and fixed IP address without any firewall protection.

4. Port 554 is the default for RTSP service. However, sometimes, some

service providers change this port number for some reasons. If so, user needs to change this port accordingly.

Dialing procedure

Compatible 3G mobile phone

1. Choose a verified player (PacketVideo, QuickTime or Real player

currently)

2. Use the following URL to access: rtsp://host/mpeg4/media.3gp

Where host is the host name or IP address of the camera. Please contact your dealer to get the approved list of compatible 3G

phone.

56B3.5.6 UPnP

UPnP is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP enabled Network Camera. If your operating system is UPnP enabled, the device will automatically be detected and a new icon will be added to “My Network Places.” If you do not want to use the UPnP functionality, it can be disabled

In addition, this device also provides UPnP IGD function for NAT traversal easily. Use NAT traversal when your device is located on an intranet (LAN) and you wish to make it available from the other (WAN) side of a NAT router. With NAT traversal properly configured, all HTTP traffic to an external HTTP port in the NAT router will be forwarded to the device.

UPnP To enable or disable the UPnP service here.

Friendly Name Shows the friendly name of this device here.

UPnP NAT Traversal When enabled, the device will attempt to configure port mapping in

a NAT router on your network, using UPnP™. Note that UPnP™ must be enabled in the NAT router first.

Port Range The port range will open in NAT router.

External IP address Show the IP address and port for WAN access through Internet. If

NAT traversal is configured successfully, user can use this IP address and port to access this device.

57B3.5.7 Bonjour

Bonjour, also known as zero-configuration networking, enables automatic discovery of computers, devices, and services on IP networks. Bonjour uses industry standard IP protocols to allow devices to automatically discover each other without the need to enter IP addresses or configure DNS servers. Specifically, Bonjour enables automatic IP address assignment without a DHCP server, name to address translation without a DNS server, and service discovery without a directory server. Bonjour is an open protocol which Apple has submitted to the IETF as part of the ongoing standards-creation process.

Bonjour To enable or disable the Bonjour service here.

Friendly Name To show the friendly name of this device here.

58B3.5.8 Onvif

ONVIF is a global and open industry forum with the goal to facilitate the development and use of a global open standard for the interface of physical IP-based security product s. Or in other wo rd s, to create a standard for how IP products within video surveillance and other physical security areas can communicate with each other.

ONVIF To enable or disable the ONVIF interface here.

Version Currently, the V1.0 or V1.01/1.02 is available.

59B3.5.9 IP Filter

You can enter different user’s IP address which are allowing enter or denying by the device.

IP Filter To enable or disable the IP filter function here.

IP Filter Policy Choose the filter policy where is denying or allowing.

60B3.5.10 IP Notification

In case the IP address is changed, system is able to send out an email to alert someone if the function is enabled.

SMTP Notification (e-mail)

Send To

Subject Type the subject/title of the E-mail.

TCP Notification

TCP Server Type the server name or the IP address of the TCP server.

TCP Port Set port number of TCP server.

Message The message will be sent to FTP server.

HTTP Notification If enable this function, then the fields below need to be filled.

If enable this function, then the “Send to“ and “Subject” field need to be filled.

Type the receiver’s e-mail address. This address is used for reply mail.

If enable this function, then the “TCP Server“, “TCP Port”, and “Message” fields need to be filled.

URL Type the server name or the IP address of the HTTP server

HTTP Login name Type the user name for the HTTP server.

HTTP Login Password Type the password for the HTTP server.

Proxy Address Type the server name or the IP address of the HTTP Proxy.

Proxy Port Set port number of Proxy.

Proxy Login name Type the user name for the HTTP Proxy.

Proxy Login Password Type the password for the HTTP Proxy.

Custom parameter User can set specific parameters to HTTP server.

Message The message will be sent to HTTP server.

27B3.6 Camera Configuration

Use this menu to set the function of the camera of Internet camera

61B3.6.1 Picture

Rotation Turn the “Mirror” and “Vertical Flip” On or OFF. The image will be

overturned as below.

White Balance: Auto: will adjust the white balance automatically.

Hold: will hold the white balance.

Power Frequency Frequency of power line: 50 or 60Hz

Color Level Large value will be colorful.

Hue Change the value will result to color tuning.

Brightness Large value will brighten camera.

Contrast Large value will contrast camera heavily.

Sharpness Large value will sharpen camera.

IR LEDs (Night Vision) User can turn Auto/Off/On/Schedule of the night mode. This

function is very useful under low illumination environment. This is an optional function by model. In case, the camera is

built-in ICR, user can configure these parameters to control ICR function. There are 4 modes of ICR: Night, Day, Auto and Schedule. In case the Auto mode is selected, user needs to specify 3 parameters in advance:

Night Mode Threshold (0~10000): this value set the threshold to activate night mode. It should be lower or equal to Day Mode Threshold.

Day Mode Threshold (0~10000): this value set the threshold to activate day mode. It should be higher or equal to Night Mode Threshold.

Delay Time: The delay time between ICR switching.

Note that Current Value is the current luminance from the

captured video. It’s a useful reference to set Day/Night Mode Threshold.

De-Noise De-Noise can remove or lower unwanted noise and preserve fine

details and edges.

Default Settings Restore to factory image settings.

62B3.6.2 Privacy Mask

Use this page to specify privacy mask window 1 to window 8 and set the name and gray level for selected window.

Add and Delete To add or delete the privacy mask windows, user can specify up to 7

windows to mask the video captured by this device. By dragging mouse on the image, you can change the position and size of the selected window accordingly.

Name Name of the specified privacy window

Level To define the gray level of mask block. The smaller value will be

darker.

63B3.6.3 PTZ Setting

This page allow user to modify the RS-485 interface according to the P/T scanner.

Camera Protocol This device can connect to a PTZ camera or speed dome camera and

controls them thru RS-485 interface.

Camera Address This is the camera ID set in PTZ camera or speed dome camera.

Note that please DO NOT changes the default value if unnecessary.

If so, user needs to check and set value properly for both sides.

Baud rate This is the communication speed between network module and P/T

scanner.

NOTE If need to change these parameters, user needs to check and set

value properly for both, network module and P/T scanner.

64B3.6.4 Preset Setting

This page provides the edit tool to modify or delete the “Preset Setting” item by item.

65B3.6.5 Tour Setting

Up to 64 positions can be preset, and the camera can be programming to move to the preset position sequentially.

Tour Name The group name of the sequence of camera tour. The maximum number of

camera tour is 16.

Running Enable or disable this camera tour.

Preset Set the sequence of the tour. Maximum 16 points can be assigned. The

selected preset position is added in the Sequence list from 1 to 16.

Wait Time Type a period of time during whi ch the camera is to stay at each preset p oint,

between 0 to 36000 seconds.

NOTE To use the camera tour function, user must preset some camera positions

first. The maximum number of preset points is 64.

28B3.7 System

Use this menu to perform the principal settings of Internet camera.

66B3.7.1 System

Device title You can enter the name of this unit here. It’s very useful to identify the

specific device from multiple units.

Software version This information shows the software version in the device.

Network LED Switch the LED light of this Internet camera on or off, that Network

LEDs will stop working, in case you don’t want other people know the camera is transferring data.

Power LED Switch the LED light of this Internet camera on or off.

Log User can check the system log information of the device, including the

Main Info, Appended Info, Operator IP, and so on …

Reload Click this button; user can refresh the log information of the device.

67B3.7.2 Date & Time

You can setup the time setting of Internet camera, make it synchronized with PC or remote NTP server. Also, you may select the correct time zone of your country.

Server Date

Displays the date and time of the device

& Time PC Time Displays the date and time of the connected PC

Adjust

Synchronize with PC

Click this option to enable time synchronization with PC time

Manual setting Click this option to set time and date manually

Synchronize with NTP

Click this option if you want to synchronize the device’s date and time with those of time server called NTP server (Network Time Protocol)

NTP server name Type the host name or IP address or domain name of the NTP

server.

NTP sync. Interval Select an interval between 1 and 23 hours at which you want to

adjust the device’s time referring to NTP server

Time zone Set the time difference from Greenwich Mean Time in the area

where the device is installed.

Daylight saving Check this ite m to enable daylight saving adjustment.

Daylight Saving Start Time

Daylight Saving Stop Time

Daylight Saving Offset

68B3.7.3 Maintenance

Sets up the date and time of daylight saving start time.

Sets up the date and time of daylight saving stop time.

Sets up the date of daylight saving offset.

Default Settings (Include the network setting)

Default Settings (Except the network setting)

Recall the device hard factory default settings. Note that click this button will reset all device’s parameters to the factory settings (including the IP address).

The unit is restarted and most current settings are reset to factory default values. This action will not reset the network setting.

Backup Setting To take a backup of all of the parameters, click this button. If

necessary, it will then be possible to return to the previous settings, if settings are changed and there is unexpected behavior.

Restore Setting Click the “Browse” button to locate the s aved backup file and

then click the “Restore Setting” button. The settings will be restored to the previous configuration.

Firmware upgrade The device supports new firmware upgrade.

1. Close all other application programs which are not

necessary for firmware update.

2. Make sure that only you access this device at this moment

3. Disable Motion Detection function.

4. Select “Firmware name”

5. Select the Firmware binary file.

Note!! That it mus , it t make sure that the Firmware only applies to this device, once update will be burned into FLASH ROM of system.

6. Once the firmware file was selected, select “Upgrade”.

7. The upgrade progress information will be displayed on the screen.

8. A message will be shown while the firmware upgraded. Once the upgrading process completed, the device will reboot the system automatically.

9. Please wait for 80 seconds, and then you can use PLANET IPWizard II to search the device again.

Warning!!! The download firmware procedure cannot be interrupted. If the power

and/or network connection are broken during the download procedure, it might possibly cause serious damag

Please be aware that you should not turn off the power during updatin

e to the device.

g the firmware

and wait for finish message.

Furthermore, do upgrade new firmware if it’s not necessary.

not try to

System Restart The device is restarted without changing any of the settings.

29B3.8 Video

This device provides 2 modes of video profile. The first one is Mega-pixel mode which supports video resolution up to Mega-pixel. However the maximum frame rate of this mode is up to 15fps only. The second one is VGA mode which supports video resolution up to VGA but frame rate can be up to 30fps. User only can select either Mega-pixel or VGA mode to operate the camera. Switching Mega-pixel and VGA, the device will take time to reboot system.

69B3.8.1 Common

Video Profile User can only choose either 720p or 2 Mega modes. 720p mod e

can serve H.264, MPEG4, and JPEG streams up to 1280x720 resolutions maximum. On the other hand, 2 Mega mode, it can streams up to 1080p or 1600x1200 resolution (depend on model) maximum.

Note that this camera supports local video output for TV monitor. It’s very useful to check view angle or focus during camera installation. However, the local video output in only available at “720p” mode. If user needs this function, must switch this camera to “720p” mode first.

Text Overlay Setting There are some important information can be embedded into

image, including date, time, and/or text.

70B3.8.2 Video Profile

It’s H.264 encoder mode in this profile.

Name To assign a name to the selected profile.

Video Type Video codec of the selected profile.

Resolution Resolution of the selected profile.

ROI Assign the selected profile as a ROI stream or not. (Only available

for the profiles with max resolution)

Rate Control Defines the rate control method of this profile. There are four

options: Constant Bit Rate (CBR), Variable Bit Rate (VBR), Enhanced Constant Bit Rate (ECBR), and Enhanced Variable Bit Rate (EVBR).

For CBR, the video bit rate is between low to high bandwidth based on different resolutions. User can set the desired bit rate to match the limitation of bandwidth.

For VBR, user should choose the quality level to set the video quality rather than bit rate. The quality level is between 1 and 100. The higher value can reach the better quality but of course will consume higher bandwidth.

For ECBR, the video bitrates is based on normal CBR mode. However, the target bitrates can be increased to max target bitrate while lots of motion in video. The max target bitrates will keep a pre-defined time period and then back to normal CBR bitrates.

For EVBR, the video bitrates is based on normal VBR mode. However, the target bitrates can be increased to max target bitrates while lots of motion in video. The max target bitrates will keep a pre-defined time period and then back to normal VBR mode.

Max Frame Rate Defines the targeted frame rate of this profile. For example, set the

frame rate to 15 fps, then the image will be updated for 15 frames per second. User can set the desired max frame rate versus video quality under the limited bandwidth.

GOP Control Defines the Intra/Inter-frame (I/P) ratio of this profile. For example,

set the GOP to 30, then the video stream will have one Intra-frame every 30 frames.

71B3.8.3 ROI

ROI means Region of Interest. Use this page to specify location of ROI windows. Only the maximum resolution profiles can be defined as ROI. In this model, the default ROI windows are profile 4 and 5.

30B3.9 Audio Configuration

It’s M-JPEG mode in this profile.

Audio To enable or disable audio function Mute While PT Mute the audio while pan and/or tilt motion Audio Mode To select Simplex or Full duplex (2-way audio) mode. Input Gain To adjust gain of input audio Output Gain To adjust gain of output audio

31B3.10 User Privilege Access Configuration

Use this menu to set the user names and password of the Administrator and up to 10 users, and access right of each user.

Viewer login Select “Anonymous” to allow any one viewing the video once

connected. Otherwise, only users in database can view the video after login.

Access right

Administrator can access every function in this device. However, Viewers only can view the video and access limited function.

PTZ Control

Add, update, and remove

Authorize this user to control PTZ function or not.

Manage the user’s account of viewer user.

of Users account

32B3.11 E-Mail Configuration

You may setup SMTP mail parameters for further operation of Event Schedule. That’s, if users want to send the alarm message out, it will need to configure parameters here and also add at least one event schedule to enable event triggering.

SMTP Server Type the SMTP server name or the IP address of the SMTP server .

Test Send a test mail to mail server to check this account is available or

not.

SMTP Port Set port number of SMTP service.

SSL Enable SSL function or not.

Select the authentication required when you send an e-mail.

SMTP Authentication

Disable: If no authentication is required when an e-mail is send. Enable: If authentication is required when an e-mail is sent.

Authentication User

Type the user name for the SMTP server if Authentication is Enable.

Name

Authentication Password Type the password for the SMTP server if Authentication is Enable.

E-mail From Type the sender’s E-mail address. This address is used for reply

e-mails.

E-mail To Type the receiver’s e-mail address.

E-mail Subject Type the subject/title of the e-mail.

33B3.12 Object Detection

Use this menu to specify motion detection window 1 to window 4 and set the conditions for detection while observing a captured image.

Add and Del To add or delete the motion windows. User can specify up to 4

Included and/or Excluded windows to monitor the video captured by this device. By dragging mouse on the image, you can change the position and size of the selected motion window accordingly.

Included or Excluded Window

Name Name of the specified motion window.

These windows can be specified as Included or Excluded type.

Included:

Windows target specific areas within the whole video image

Excluded:

Windows define areas within an Include window that should be ignored (areas outside Include windows are auto m atically ignored)

Object Size Defines the object size of motion detection. The higher object size will

only larger objects trigger motion detection. The lower object size will even small objects trigger motion detection too. Generally speaking, the smaller size will be easier to trigger event.

Sensitivity Defines the sensitivity value of motion detection. The higher value will

be more sensitivity.

34B3.13 Event Server Configuration

72B3.13.1 FTP Server

You may setup FTP parameters for further operation of Event Schedule. That’s, if users want to send the alarm message to an FTP server, it will need to configure parameters here and also add at least one event schedule to enable event triggering as SMTP.

Name User can specify multiple FTP paths as wish. Therefore, user

needs to specify a name for each FTP setting.

FTP Server Type the server nam e or the IP address of the FTP server.

Test Check the FTP server whether this account is available or not.

FTP Login name Type the user name for the FTP server.

FTP Login Password Type the password for the FTP server.

FTP Port Set port number of FTP service.

FTP Path Set working directory path of FTP server.

FTP Passive Mode Select passive or active mode connecting to FTP server.

73B3.13.2 TCP Server

In addition to send video file to FTP server, the device also can send event message to specified TCP server.

Name User can specify multiple TCP servers as wish. Therefore, user

needs to specify a name for each TCP server setting.

TCP Server Type the server name or the IP address of the TCP server.

TCP Port Set port number of TCP server.

74B3.13.3 HTTP Server

The device also can send event message to specified HTTP server.

Name User can specify multiple HTTP servers as wish. Therefore, user

needs to specify a name for each HTTP server setting.

URL Type the server name or the IP address of the HTTP server.

Test Check the HTTP server whether it is available or not.

HTTP Login name Type the user name for the HTTP server.

HTTP Login Password Type the password for the HTTP server.

Proxy Address Type the server name or the IP address of the HTTP Proxy.

Proxy Login name Type the user name for the HTTP Proxy.

Proxy Login Password Type the password for the HTTP Proxy.

Proxy Port Set port number of Proxy.

75B3.13.4 SAMBA Server

The device also can send video stream to specified SAMBA server. Most of the time, the SAMBA server will be another PC or NAS server.

Name User can specify multiple HTTP servers as wish. Therefore, user

needs to specify a name for each HTTP server setting.

SAMBA Server Type the server name or the IP address of the SAMBA server.

Test Check the SAMBA server whether this account is available or not.

SAMBA Login name Type the user name for the SAMBA server.

SAMBA Login Password Type the password for the SAMBA server.

SAMBA Path Set working directory path of SAMBA server.

35B3.14 Event Schedule Configuration

This menu is used to specify the schedule of Events and activate the some actions provided by this device.

Name Name of the Event or Schedule. Enable Enable or disable this Event or Schedule. Type Schedule start with Event trigger or Schedule trigger. Enable Time Define the feasible time slot. Trigger by Select the triggered sources with event trigger. Action Define the actions once event triggered.

Example1.

Send file to FTP server by motion triggered always:

1. Select event trigger

2. Enable time: start from 00:00 to 24:00 every day

3. Trigger by: Motion Area (Added in Object Detection page)

4. Action : Send FTP (Add in Event Server -> FTP Server page)

Example2.

Send file to E-Mail server by motion triggered from Friday 18:00 to Saturday 06:00

1. Select event trigger.

2. Enable time: start from Friday 18:00 and keep work in 12 hours, so it will stop on Saturday 06:00.

3. Trigger by : Motion Area (Added in Object Detection page)

4. Action : Send e-mail (Add in E-Mail page)

i. To email address: You need to input the receiver email

address.

ii. Subject: You could specify the email subject.

iii. Message: You could specify the email content.

Example3.

Send file to E-Mail server by motion triggered from Friday 18:00 to 24:00 from Monday to Friday.

1. Type: Select schedule trigger and interval is 10-minute.

2. Enable Time: Select Monday to Friday, and set start time from 18:00 and keep work in 6 hours.

3. Trigger by: You do not need to choose it, because this will be triggered every minute.

4. Action: Voice Alert.

36B3.15 Record Configuration

User can choose the type of record file for event or schedule application.

Record File Type Choose AVI or JPEG file format for record file.

Record File Prefix Define the prefix of recorded filename.

Pre-Trigger Duration Define the maximum duration of pre-alarm.

Best Effort Duration Define the best effort duration of post-alarm.

Max File Size Define the maximum buffer size of record file.

3BAppendix A: Alarm I/O Connector

Some features of the Camera can be activated by the external sensor that senses physical changes in the area Camera is monitoring. These changes can include intrusion detection or certain physical change in the monitored area. For examples, the external sensor can be a door switch or an infrared motion detector. These devices are customer provided, and are available from dealers who carry surveillance and security products. Electrically, they must be able to provide a momentary contact closure.

This Camera provides wires for general I/O terminal and RS-485 interface as below:

Cable for I/O connectors:

Name Cable Color Function

12VDC Brown/White DC 12V (50mA maximum) GND Blue/White GND D+ Purple/White RS-485 data + D- Gray RS-485 data DI Green/White Digital signal input DO Orange/White Digital signal output

User can refer to the schematic below to make a proper connection between I/O connector and external sensor and output device.

Explanation of External I/O Circuit Diagram:

CAUTION!

9 The low voltage/current circuits and high voltage/current circuits are in the

network camera circuit. The qualified electrician should do the wring not by yourself incorrect wiring could damage network camera. You could receive the fatal electric shock.

9 The external I/O is not capable of connecting directly to devices that require

large amounts of current. In some cases, a custom interface circuit (customer provided) may have to be used. Serious damage to network camera may result if a device is connected to the external I/O that exceeds its electrical capability.

4BAppendix B: PING IP Address

The PING (stands for Packet Internet Groper) command is used to detect whether a specific IP address is accessible by sending a packet to the specific address and waiting for a reply. It’s also a very useful tool to confirm Internet camera installed or if the IP address conflicts with any other devices over the network.

If you want to make sure the IP address of Internet camera, utilize the PING command as follows:

z Start a DOS window. z Type ping x.x.x.x, where x.x.x.x is the IP address of the Internet camera.

The replies, as illustrated below, will provide an explanation to the problem.

If you want to detect any other devices conflicts with the IP address of Internet camera, also can utilize the PING command but you must disconnect the Internet camera from the network first.

5BAppendix C: 3GPP Access

To use the 3GPP function, in addition to previous section, you might need more information or configuration to make this function work.

Note

That to use the 3GPP function, it strongly recommends to install the Networked Device with a public and fixed IP address without any firewall protection.

RTSP Port:

Port 554 is the default for RTSP service. However, sometimes, some service providers change this port number for some reasons. If so, user needs to change this port accordingly.

Dialing procedure:

1. Choose a verified player (PacketVideo or Realplayer currently)

2. Use the following URL to access:

rtsp://host/mpeg4/media.3gp

Where host is the host name or IP address of the camera.

Compatible 3G mobile phone:

Please contact your dealer to get the approved list of compatible 3G phone.

Note

Besides IP camera and 3G mobile phone. You will also need to make sure the ISP and company has provided the 3GPP service to you.

6BAppendix D: Bandwidth and Video Size

Estimation

The frame rate of video transmitted from the Internet camera depends on connection bandwidth between client and server, video resolution, codec type, and quality setting of server. Here is a guideline to help you roughly estimate the bandwidth requirements for your Internet camera.

The required bandwidth depends on content of video source. The slow motion video will produce smaller bit rate generally and fast motion will produce higher bit rate vice versa. Actual results generated by the Internet camera may be varying.

Image

Resolution

160 x 120 (QQVGA) 320 x 240

(QVGA)

640 x 480

(VGA)

1280x1024

(SXGA)

Average range of data

sizes for M-JPEG mode

3 ~ 6k byte per frame

8 ~ 20k byte per frame

20 ~ 50K byte per frame

100 ~ 200k byte per

frame

Average bit rate for

MPEG-4 mode

64kbps~256kbps

@ 30fps

256kbps~768kbps

@ 30fps

512kbps~2048kbps @

30fps

Average bit rate for

H.264 mode

32kbps~192kbps

@ 30fps

192kbps~512kbps

@ 30fps

384kbps~1536kbps

@ 30fps

512kbps~3076kbps

@ 15fps

NOTE Audio streaming also takes bandwidth around 5 kbps to 64kbps. Most xDSL/Cable

modem upload speeds may not even reach up to 128 kbps. Thus, you may not be able to receive any video while streaming audio on a 128 kbps or lower connection. Even though the upload speed is more than 128kbps, for optimal video performance, disabling audio streaming will get better video performance.

7BAppendix E: DDNS Application

1. Preface

If you have a Cable modem or xDSL, this is a great way to host your own Networked Device or other TCP/IP Service. Get your own domain like www.yourname.com, www.yourname.com.tw etc. (Note: This domain must be registered with Internic via registration authorities such as Network Solutions, DirectNIC, Register.com etc). Your domain name's dynamic IP address is automatically tracked by a DDNS server.

Host your own Networked Device and much more no matter what your computer's IP address may be and even if you have dialup, DSL or cable modem internet connection where your computer's IP address changes all the time!! DDNS service supports all top level domain names including but not limited to .com, .net, .org, .to, .uk etc.

2. Ethernet Network Environment

Normally, DDNS service is only necessary for the users that could only obtain dynamic IP addresses. As to the users that could obtain the static valid IP address, they do not usually have to apply the DDNS service. Before we decide if DDNS is necessary for the users, we have to check what kind of Ethernet network environment we have to install our Networked Device on.

(1) Environment of Fixed Valid IP Network

If users could obtain valid IP addresses, they could save the effort to apply DDNS service. Because the IP address in this environment is fixed, users could input the IP address or domain name of demo site directly in the IE browser.

(2) Environment of Dynamic IP Net work

If users is under an environment of dynamic IP network (Dial-up xDSL), they have to apply a domain name in advance. Then apply DDNS service. Finally setup the necessary information of DDNS and PPPoE of the Networked Device in order to let the outside administrator be able to access through internet.

3. Application Steps – DDNS & Domain Name

(1). Visit the following web site:

HUhttp://www.dyndns.org/UH

(2). Click “Account”

(3). After the columns show up at the left side, click “Create Account”.

(4). Fill the application agreement and necessary information.

a. Username b. E-mail address and confirmation c. Password and confirmation d. Submit all the input information and finish creating an account

Click these two options

(5). Check your e-mail mailbox. There will be an e-mail with a title “Your DynDNS Account

Information“. Click the hyperlink address to confirm the DDNS service that you just applied. Then DDNS you applied activated.

Click to confirm

(6). Enter the web page

HUhttp://www.dyndns.org/UH again. Input your username and password

that you just applied to login administration interface of DDNS server.

Input your account

(7). If the correct username and password are input, you can see the following picture at the

top-right of the login page.

(8). Click the “Services”.

(9). Click the “ Dynamic DNS ”.

(10). Click the “Create Hosts”.

(11). We could create a domain name without any charge at this step. First, we input the host name. (No.1) Then we pick a domain that is easy to remember. Finally (No.2), click the “Add Host” to submit the domain name information. (No.3)

4. Setup the DDNS and PPPoE of Network Device

At last, users have to enter the web page of Networked Device and setup the necessary information of DDNS and PPPoE after the application of DDNS service. Please check the user manual to access the DDNS and PPPoE pages. After saving the modification, restart the device. The external users could browse the Networked Device by the input of their domain name.

8BAppendix F:

Configure Port Forwarding Manually

The device can be used with a router. If the device wants to be accessed from the WAN, its IP address needs to be setup as fixed IP address, also the port forwarding or Virtual Server function of router needs to be setup. This device supports UPnP traversal function. Therefore, user could use this feature to configure port forwarding of NAT router first. However, if user needs to configure port forwarding manually, please follow the steps as below:

Manually installing the device with a router on your network is an easy 3–step procedure as following:

1. Assign a local/fixed IP address to your device

2. Access the Router with Your Web browser

3. Open/Configure Virtual Server Ports of Your Router

1. Assign a local/fixed IP address to your device

The device must be assigned a local and fixed IP Address that allows it to be recognized by the router. Manually setup the device with a fixed IP address, for example, 192.168.0.100.

2. Access the Router with Your Web browser

The following steps generally apply to any router that you have on your network. The PLANET WNRT-620 is used as an example to clarify the configuration process. Configure the initial settings of the router by following the steps outlined in the router’s Quick Installation Guide.

If you have cable or DSL service, you will most likely have a dynamically assigned WAN IP Address. ‘Dynamic’ means that your router’s WAN IP address can change from time to time depending on your ISP. A dynamic WAN IP Address identifies your router on the public network and allows it to access the Internet. To find out what your router’s WAN IP Address is, go to the Status screen on your router and locate the WAN information for your router. As shown on the following page the WAN IP Address will be listed. This will be the address that you will need to type in your web browser to view your camera over the Internet. Be sure to uncheck the Reset IP address at next boot button at the top of the screen after modifying the IP address. Failure to do so will reset the IP address when you restart your computer.

Your WAN IP Address will be listed here.

3. Open/set Virtual Server Ports to enable remote image viewing

The firewall security features built into the router and most routers prevent users from accessing the video from the device over the Internet. The router connects to the Internet over a series of numbered ports. The ports normally used by the device are blo cked from access over the Internet. Therefore, these ports need to be made accessible over the Internet. This is accomplished using the Virtual Server function on the router. The Virtual Server ports used by the camera must be opened through the router for remote access to your camera.

Follow these steps to configure your router’s Virtual Server settings

z Click Enabled. z Enter a unique name for each entry. z Select Both under Protocol Type (TCP and UDP) z Enter your camera’s local IP Address (e.g., 192.168.0.100, for example) in the Private

IP field.

z If you are using the default camera port settings, enter 80 into the Public and

Private Port section, click Add.

A check mark appearing before the entry name will indicate that the ports are enabled.

NOTE Some ISPs block access to port 80. Be sure to check with your ISP so that you can

open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you will need to change the port the camera uses from 80 to something else, such as 8080. Not all routers are the same, so refer to your user manual for specific instructions on how to open ports.

Enter valid ports in the Virtual Server section of your router. Please make sure to check the box on this line to enable settings. Then the device can be access from WAN by the router’s WAN IP Address.

By now, you have finished your entire PC configuration for this device.

9BAppendix G:

Troubleshooting & Frequently Asked Questions

Features

The video and audio codec is adopted in the device.

The device utilizes H.264, MPEG-4 and M-JPEG triple compression to providing high quality images. Where H.264 and MPEG-4 are standards for video compression and M-JPEG is a standard for image compression.

The audio codec is defined as AMR for 3GPP and G.711/G.726 for RTSP streaming.

The maximum number of user accesses the device simultaneously.

The maximum number of users is limited to 20. However, it also depends on the total bandwidth accessed to this device fro m cli en ts. The maximum data throughput of the device is around 20~25Mbps for UDP mode and 10Mbps for HTTP mode. Therefore, the actual number of connected clients is varying by streaming mode, settings of resolution, codec type, frame rate and bandwidth. Obviously, the performance of the each connected client will slow down when many users are logged on.

The device can be used outdoors or not.

The device is not weatherproof. It needs to be equipped with a weatherproof case for outdoors using. However, equipped with a weatherproof case might disable the audio function of the device.

Install this device

Status LED does not light up. z Check and confirm that the DC power adaptor, included in

packaged, is used. Secure the power connector and re-power it on again.

The network cabling is required for the device.

The device will be installed and work if a firewall exists on the network.

The username and password for the first time or after factory default reset

Forgot the username and password

z If the problem is not solved, the device might be faulty. Contact

your dealer for further help.

The device uses Category 5 UTP cable allowing 10 and/or 100 Base-T networking.

If a firewall exists on the network, port 80 is open for ordinary data communication. The HTTP port and RTSP port need to be opened on the firewall or NAT router.

Username = admin and leave password blank. Note that it’s all case sensitivity.

Follow the steps below.

1. Restore the factory default setting by press pressing and holding down more than 3 seconds on the device.

2. Reconfigure the device.

Forgot the IP address of the device.

IPWizard program cannot find the device.

Internet Explorer does not seem to work well with the device

IPWizard program fails to save the network parameters.

Check IP address of device by using the IPWizard program or by UPnP discovery or set the device to default by Reset button.

z Re-power the device if cannot find the unit within 1 minutes. z Do not connect device over a router. IPWizard program cannot

detect device over a router.

z If IP address is not assigned to the PC which running IPWizard

program, then IPWizard program cannot find device. Make sure that IP address is assigned to the PC properly.

z Antivirus software on the PC might interfere with the setup

program. Disable the firewall of the antivirus software during setting up this device.

z Check the firewall setting of your PC or Notebook.

Make sure that your Internet Explorer is version 6.0 or later. If you are experiencing problems, try upgrading to the latest version of Microsoft’s Internet Explorer from the Microsoft webpage.

Network may have trouble. Confirm the parameters and connections of the device.

UPnP NAT Traversal

Can not work with NAT router Maybe NAT router does not support UPnP function. Please check

user’s manual of router and turn on UPnP function.

Some IP cameras are working but others are failed

Maybe too many IP cameras have been installed on the LAN, and then NAT router is out of resource to support more cameras. You could turn off and on NAT router to clear out of date information inside router.

Access this device

Cannot access the login page and other web pages of the Network Camera from Internet Explorer

z Maybe the IP Address of the Network Camera is already being

used by another device or computer. To confirm this possible problem, disconnect the Network Camera from the network first, and then run the PING utility to check it out.

z Maybe due to the network cable. Try correcting your network

cable and configuration. Test the network interface by connecting a local computer to the Network Camera via a crossover cable.

z Make sure the Internet connection and setting is ok. z Make sure enter the IP address of Internet Explorer is correct. If

the Network Camera has a dynamic address, it may have changed since you last checked it.

z Network congestion may prevent the web page appearing

quickly. Wait for a while.

The IP address and Subnet Mask of the PC and Network Camera must be in the same class of the private IP address on the LAN.

z Make sure the http port used by the Network Camera, default=80,

is forward to the Network Camera’s private IP address.

z The port number assigned in your Network Camera might not be

available via Internet. Check your ISP for available port.

z The proxy server may prevent you from connecting directly to the

Network Camera, set up not to use the proxy server.

z Confirm that Default Gateway address is correct. z The router needs Port Forwarding feature. Refer to your router's

manual for details.

z Packet Filtering of the router may prohibit access from an

external network. Refer to your router's manual for details.

z Access the Network Camera from the Internet with the global IP

address of the router and port number of Network Camera.

z Some routers reject the global IP address to access the Network

Camera on the same LAN. Access with the private IP address and correct port number of Network Camera.

Image or video does not appear in the main page.

How to check the device’s ActiveX is installed on your computer

Internet Explorer displays the following message: “Your current security settings prohibit downloading ActiveX controls”.

z When you use DDNS, you need to set Default Gateway and DNS

server address.

z If it’s not working after above procedure, reset Network Camera

to default setting and installed it again.

z The first time the PC connects to Network Camera, a pop-up

Security Warning window will appear to download ActiveX Controls. When using Windows XP, or Vista, log on with an appropriate account that is authorized to install applications.

z Network congestion may prevent the Image screen from

appearing quickly. You may choose lower resolution to reduce the required bandwidth.

Go to C:\Windows\Downloaded Program Files and check to see if there is an entry for the file “IPCamera Control”. The status column should show “Installed”. If the file is not listed, make sure your Security Settings in Internet Explorer are configured properly and then try reloading the device’s home page. Most likely, the ActiveX control did not download and install correctly. Check your Internet Explorer security settings and then close and restart Internet Explorer. Try to browse and log in again.

Setup the IE security settings or configure the individual settings to allow downloading and scripting of ActiveX controls.

The device work locally but not externally.

z Might be caused from the firewall protection. Check the Internet

firewall with your system or network administrator. The firewall may need to have some settings changed in order for the device

to be accessible outside your LAN.

z Make sure that the device isn’t conflicting with any other web

server running on your LAN.

z Check the configuration of the router settings allow the device to

be accessed outside your local LAN.

z Check the bandwidth of Internet connection. If the Internet

bandwidth is lower than target bit rate, the video streaming will not work correctly.

The unreadable characters are displayed.

Frame rate is slower than the setting.

Blank screen or very slow video when audio is enabled.

Image Transfer on e-mail or FTP does not work.

Use the operating system of the selected language. Set the Encoding or the Character Set of the selected language on the Internet Explorer.

z The traffic of the network and the object of the image affect the

frame rate. The network congestion causes frame rate slower than the setting.

z Check the bandwidth of Internet connection. If the Internet

bandwidth is lower than target bit rate, the video streaming will not work correctly.

z Ethernet switching hub can smooth the frame rate.

z Your connection to the device does not have enough bandwidth

to support a higher frame rate for the streamed image size. Try reducing the video streaming size to 160x120 or 320x240 and/or disabling audio.

z Audio will consume 32 kbps. Disable audio to improve video.

Your Internet connection may not have enough bandwidth to support streaming audio from the device.

z Default Gateway and DNS server address should be set up

correctly.

z If FTP does not work properly, ask your ISP or network

administrator about the transferring mode of FTP server.

Video quality of the device

The focus on the Camera is bad. The lens is dirty or dust is attached. Fingerprints, dust, stain, etc. on

the lens can degrade the image quality.

The color of the image is poor or strange.

z Adjust White Balance. z To insure the images you are viewing are the best they can be,

set the Display property setting (color quality) to 16bit at least and 24 bit or higher if possible within your computer.

z The configuration on the device image display is incorrect. You

need to adjust the image related parameters such as brightness, contrast, hue and sharpness properly.

Image flickers. z Wrong power line freque ncy makes imag es flicker. Make su re the

50 or 60Hz format of your device.

z If the object is dark, the image will flicker. Make the condition

around the Camera brighter.

Miscellaneous

Can not play the recorded ASF file Please installed Microsoft®’s DirectX 9.0 or later and uses the

Windows Media Player 11.0 or later to play the AVI filed recorded by the Device.

10BAppendix H: Product Specification

Product ICA-HM351

Video Specification

Image Sensor 1/2.7“ 2 Mega-pixel Progressive CMOS Lens 4mm fixed lens with Fixed Iris Sensitivity 0.5 Lux @ F1.4 View Angle H: 66 Degree / V: 52 Degree Video Encoder H.264 / MPEG-4 / M-JPEG Rate Control CBR (Constant Bit Rate) / VBR (Variable Bit Rate) Video Resolution 1920 x 1080 / 1280 x 720 / 640 x 360 / 320 x 180 / 160 x 90 Frame Rate Up to 30fps for all resolutions (2M Real-time)

AE, AWB

3D Noise reduction

Image Control

Color, Brightness, Sharpness, Contrast, Hue

Mirror/Flip

8 Privacy Masks

Text, time and date overlay

Audio Specification

Audio Codec RTSP: G.711 64kbps, G.726 32kbps

3GPP: AMR Audio Streaming One-Way or Two-Way Microphone(Audio Input) External microphone input, Phone Jack Audio Output Adjustable audio output gain, Phone Jack

Network and Configuration

Network Interface 1 x RJ-45 Network Standard IEEE 802.3 / IEEE 802.3u / IEEE 802.3af

Network Protocol

Browser / Software

IPv4, TCP, UDP, HTTP, HTTPS, SMTP, FTP, NTP, DNS, DDNS, DHCP, DIPS, ARP, Bonjour, UPnP, RTSP, RTP, RTCP, IGMP, PPPoE, 3GPP, Samba, ICMP

Microsoft ® Internet Explorer 6.0 or later

PLANET Cam Viewer 3 Lite/Pro

Motion Detection 10 areas definable

Environment Specifications

Power Requirement 12V DC, 1A PoE

(PoE is for IP cam & IR LED only, Heater & fan require external adaptor 12V/1A) Dimension (W x D x H) 141 x 310 x 120 mm Weight 1335 g

Power Consumption

Max. 8W for camera and IR LEDs

IEEE 802.3af

Max. 5W for heater only

Illumination LED 88pcs IR LED, 35M IR Distance

Heater

Heater & Fan

Protection Class IP-66 classification with Weather proof Operating Temperature -30 ~ 60 Degree C Operating Humidity 0 ~ 95% (non-condensing) Emission CE, FCC

ON: 15 Degree C

OFF:25 Degree C

Blower

ON: 37 Degree C

OFF:25 Degree C

PLANET ICA-HM351 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1. 0BIntroduction

11B1.1 Overview

12B1.2 Features

13B1.3 Package Contents

1B2. Basic Setup

14B2.1 System Requirements

15B2.2 Physical Description

37B2.2.1 Identification of ICA-HM351 cable

16B2.3 Hardware Installation

38B2.3.1 Physical Installation

17B2.4 Initial Utility Installation

18B2.5 Preparation

39B2.5.1 Search and View by PLANET IPWizard

2.6 19BUsing UPnP of Windows XP, Vista or Win7

40B2.6.1 Windows XP

41B2.6.2 Windows Vista

42B2.6.3 Windows 7

2.7 20BInstall the Device behind a NAT Router

2.8 21BSetup ActiveX to use the Internet Camera

43B2.8.1 Internet Explorer 6 for Windows XP

44B2.8.2 Internet Explorer 7 for Windows XP

2.8.3 Internet Explorer 7 for Windows Vista and Win7

3 2BWeb-based Management

22B3.1 Introduction

23B3.2 Connecting to Internet Camera

24B3.3 Live View

25B3.4 ActiveX Control

45B3.4.1 Digital Zoom

46B3.4.2 Record

48B3.4.4 Voice

49B3.4.5 Statistics

50B3.4.6 About

26B3.5 System Setting

51B3.5.1 Network

52B3.5.2 HTTPS

53B3.5.3 DDNS server

54B3.5.4 PPPoE

55B3.5.5 Streaming

56B3.5.6 UPnP

57B3.5.7 Bonjour

58B3.5.8 Onvif

59B3.5.9 IP Filter

60B3.5.10 IP Notification

27B3.6 Camera Configuration

61B3.6.1 Picture

62B3.6.2 Privacy Mask

63B3.6.3 PTZ Setting

64B3.6.4 Preset Setting

65B3.6.5 Tour Setting

28B3.7 System

66B3.7.1 System

67B3.7.2 Date & Time

68B3.7.3 Maintenance

29B3.8 Video

69B3.8.1 Common

70B3.8.2 Video Profile

71B3.8.3 ROI

30B3.9 Audio Configuration

31B3.10 User Privilege Access Configuration

32B3.11 E-Mail Configuration

33B3.12 Object Detection

34B3.13 Event Server Configuration

72B3.13.1 FTP Server

73B3.13.2 TCP Server

74B3.13.3 HTTP Server

75B3.13.4 SAMBA Server

35B3.14 Event Schedule Configuration

36B3.15 Record Configuration

3BAppendix A: Alarm I/O Connector

4BAppendix B: PING IP Address

5BAppendix C: 3GPP Access

7BAppendix E: DDNS Application

10BAppendix H: Product Specification