PLANET ICA-HM240 User Manual

their respectiveowners. Copyright © 2010 PLANET Technology Corp. All rights reserved.

PLANET Technology Corporation

11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw

VERIFY THE CONTENTS INSIDE PACKAGE BOX

The package should contain the items plus ICA-HM240. If any item is missing or damaged, please cont act the seller immediately

ICA-HM240 ICA-HM240

x 3

x 3

Quick Installation Guid e

ICA- HM240 Physical Detail

CD- ROM

Power Ada pter

Camera Mounting Kit

1. LAN Socket

2. Reset Button

3. Power Jack

4. MIC in

5. Line out

6. DI/DO

1. LAN socket Please use CAT-5 cable to connect the IP Camera to a 10/100Mbps Ethernet switch or hub.

LAN LED (Green) : This indicator will be flashing while network accessing via Ether net.
Power LED (Orange) : This indicator is used to indicate whether DC power is on or not.

2. Reset Button This button is used to restore the all factory default settings.

3. Power Jack The input power is 12VDC
Note : 1. Supply the power to the IP Camera with the power adapter included in package.

2. Use either 12VDC power or 802.3af PoE. Please do not apply both at the same time.

4. MIC IN Please connect a microphone to the IP Camera.

5. Line Out Please connect a loud speaker to the IP Camera. This function is for voic e alerting and two-way audio.

6. DI/DO Please connect to sensor in and alarm out equipment.

their respectiveowners. Copyright © 2010 PLANET Technology Corp. All rights reserved.

PLANET Technology Corporation

11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw

Step 1 : Connecting Network and AC Adapter Power

User PC

(192.168.0.X)

Ethernet Switch

ICA-HM240

1-a. Plug an Ethernet cable into the IP Camera

Connect an Ethernet cable to the L AN socket and attach it to the network. When this switch/hub is a PoE device, you can ignore the next
step.

1-b. Connect the external power supply to IP Camera

Connect the attached power adapter to the DC power jack of the IP Camera.
Once you have installed the IP Camera well and powered it on, the power indicator (orange) will tur n on later. The power indicator turned on,
it means the system is booting up successfully. Furthermore, if you have a proper networ k connection, and access to the camera, the LAN
indicator (green) will flash.

Note : Use the power adapter, 12VDC, included in the package and connect it to wall outlet for AC power

Step 2 : Computer Network Setup

2.1 If there is DHCP server existed in the net work, please refer to the
DHCP ser ver IP table for the IP of the camera.

2.2 If there is no DHCP server, set your computer’s IP address to

192.168.0.x, where x is an integer bet ween 1 to 25 4 (except 20
where is being used for the camera by default).

2.3 Or install the wizard utility to search the camera.

Step 3 : Login Prompt

Start the web browser on the computer and type the IP address of the
camera, and the Default IP: “http://192.168.0. 20”
You’ll be prompted to input user name and password: admin / null
(without password)

Further Configuration

For detail configuration, please check user’s manual on the bundled CD.
If you have any other questions, please contact the dealer where you purchased this product or you can contact PLANET directly at the following
email address: suppor [e-mail]

Quick GuideQuick Guide

2011-AB5340-001