Planet ICA-HM101, ICA-HM101W User Manual
User’s Manual
ICA-HM101 / ICA-HM101W
Wired / Wireless
H.264 Mega-Pixel IP Camera
Copyright
Copyright © 2012 by PLANET Technology Corp. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mecha nical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Any software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or
its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software. Further, PLANET reserves the
right to revise this publication and to make changes from time to time in the contents hereof
without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Federal Communication Commission Interference St atement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance. (example-use only shielded interface cables when connecting
to computer or peripheral devices). Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two
conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must
accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for a n uncontrolled enviro nment .
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human
proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity
1
when working with electrical equipment. All guidelines of this and of the computer manufacture
must therefore be allowed at all times to ensure the safe use of the equipment
.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may ca use radio interfere nce,
in which case the user may be required to take adequate measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users
of electrical and electronic equipment should understand the meaning of the
crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal
waste and have to collect such WEEE separately.
Revision
User’s Manual for PLANET Wired/Wireless H.264 Mega-Pixel IP Camera
Model: ICA-HM101 / ICA-HM101W
Rev: 1.0 (April. 2012)
Part No. EM-ICAHM101 Series_v1.0
2
Table of Content
1. Introduction......................................................................................................5
1.1 Overview.................................................................................................5
1.2 Features..................................................................................................5
1.3 Package Contents...................................................................................6
2. Basic Setup ..................................................................................................... 7
2.1 System Requirement...............................................................................7
2.2 Physical Description................................................................................8
2.2.1 Terminal Connections ...................................................................8
2.2.2 Bottom Panel................................................................................9
2.2.3 Side Panel ..................................................................................11
2.3 Initial Utility Installation..........................................................................13
2.4 Preparation............................................................................................15
2.4.1 Search and View by PLANET IP Wizard II..................................15
2.5 Using UPnP of Windows XP or Vista.....................................................19
2.5.1 Windows XP ................................................................................19
2.5.2 Windows Vista.............................................................................23
2.6 Setup ActiveX to use the Internet Camera ............................................24
2.6.1 Internet Explorer 6 for Windows XP............................................24
2.6.2 Internet Explorer 7 for Windows XP............................................25
2.6.3 Internet Explorer 7 for Windows Vista.........................................26
3. Web-based Management ..............................................................................28
3.1 Introduction............................................................................................28
3.2 Connecting to Internet Camera .............................................................28
3.3 Live View...............................................................................................30
3.4 ActiveX Control......................................................................................32
3.4.1. Digital Zoom................................................................................33
3.4.2. Record........................................................................................33
3.4.3. Snapshot.....................................................................................34
3.4.4. Volume........................................................................................34
3.4.5. About..........................................................................................35
3.5 Network Configuration...........................................................................35
3.5.1. Network.......................................................................................35
3.5.2. Wireless (ICA-HM101W only).....................................................37
3.5.3. IPv6 function...............................................................................41
3.5.4. HTTPS........................................................................................42
3.5.5. DDNS server...............................................................................42
3.5.6. PPPoE........................................................................................44
3.5.7. Streaming....................................................................................45
3.5.8. UPnP..........................................................................................46
3.5.9. Bonjour.......................................................................................47
3.5.10. ONVIF......................................................................................48
3.5.11. IP Filter.....................................................................................49
3.5.12. IP Notification...........................................................................50
3.6 Camera Configuration...........................................................................52
3.6.1. Picture.........................................................................................52
3
3.6.2. Privacy Mask ..............................................................................54
3.7 System..................................................................................................55
3.7.1. System........................................................................................55
3.7.2. Date & Time................................................................................56
3.7.3. Maintenance...............................................................................57
3.8 Video .....................................................................................................59
3.8.1. Common.....................................................................................59
3.8.2. Video Profile...............................................................................60
3.8.3. ROI.............................................................................................61
3.9 Audio Configuration...............................................................................62
3.10 User Privilege Access Configuration...................................................63
3.11 E-Mail Configuration...........................................................................64
3.12 Object Detection .................................................................................65
3.13 Storage Configuration.........................................................................66
3.14 Recording List.....................................................................................67
3.15 Continuous Recording ........................................................................68
3.16 Event Server Configuration................................................................. 69
3.16.1 FTP Server...............................................................................69
3.16.2 TCP Server ..............................................................................70
3.16.3 HTTP Server ............................................................................ 71
3.16.4 SAMBA Server.........................................................................72
3.17 Event Schedule Configuration ............................................................73
3.18 Record Configuration..........................................................................77
Appendix A: PING IP Address ...........................................................................78
Appendix B: 3GPP Access.................................................................................79
Appendix C: Bandwidth and Video Size Estimation...........................................80
Appendix D: DDNS Application..........................................................................81
Appendix E: Configure Port Forwarding Manually .............................................87
Appendix F: Power Line Frequency...................................................................77
Appendix G: Troubleshooting & Frequently Asked Questions............................78
Appendix H: Product Specification.....................................................................83
4
1. Introduction
PLANET has announced a 2 Mega-Pixel PoE Cube IP camera, ICA-HM101, for meeting the
feedback from worldwide market. The ICA-HM101 with built-in high performance 2 Mega-Pixel
CMOS sensor delivers high quality image at maximum UXGA (1600x1200) resolutions.
Integrated the next generation video compression technology – H.264, the ICA-HM101 can
compress the video size to smaller one for users to transfer the Mega-Pixel image on Internet
easily. Multi-profile stands for video stream simultaneously. The ICA-HM 101 ca n generate H.2 64 /
MPEG-4 and M-JPEG streaming to different users at the same time. It allows up to 20 users to
access the ICA-HM101 simultaneously. With this state-of-the-art design, the ICA-HM101 is
considerable to fit in various network environments.
The ICA-HM101 features 0.5 lux illumination. 12 white LEDs built around the lens bring the
clearest vision at night. The ICA-HM101 offers color pictures both in the day and night with built-in
CMOS sensor supporting up to 10 meters. It also uses new High-Light LED to provide greater
performance in the dark and longer life of LED.
Supports Store-to-NAS function, the ICA-HM101 can work alone and save the video file to a NAS
directly, which can save the PC resource and keep monitoring the environment with motion
detection at 7/24. The ICA-HM101’s PIR motion sensor detects motion, images and voices are
transmitted. The ICA-HM101 takes surveillance using 2-Way audio. The administrator can speak
to anyone at ICA-HM101 remote site with a speaker connected. Compliant with IEEE 802.3af PoE
interface, the ICA-HM101 can be located in places where there are no power outlets.
The ICA-HM101 can be managed by PLANET Cam Viewer Three, the professional management
software for multi-camera video surveillance application, to provide monitoring, recording and
event management functions. The Cam Viewer Plus enables you to setup a comprehensive and
effective surveillance system quickly and easily. With the ICA-HM101 managed by the Cam
Viewer Three, it provides an enhanced professional security environment to protect your property
and life.
1.1 Overview
This user’s guide explains how to operate this camera from a computer. User should read this
manual completely and carefully before you operate the device
1.2 Features
2 Mega-Pixel CMOS sensor built-in
12 white-light LEDs support up to 10 meters visible distance at night
4.3mm Fixed Lens Provides 56 Degree Horizontal / 43 Degree Vertical Angle of View
High Resolution Video Preview: UXGA (1600X1200) pixels
Min Illumination : 0.5 lux @ F1.2
Built-in PIR sensor (6m/120° coverage) for thermal/motion detection
Intelligent motion detection up to 10 zones
Multi-profile encoder supports H.264 / MPEG-4 and M-JPEG video compression
simultaneously
5
Support both Variable Bit Rate and Variable Frame Rate
2 MP resolution or 720p mode selectable
Up to 30fps for 1280x720 resolution and up to 15fps for 1600x1200 resolutions
Digital WDR to provide clear images even under back light circu mstances
3D de-noise to improve picture quality at low lux
2-Way audio with built-in microphone an d speaker
Sensor input and alarm output
Easy configuration and management via Windows-based utility or web interface
IEEE 802.11n Wireless LAN Capability (ICA-HM101W only)
WEP/WPA/WPA2-PSK wireless security (ICA-HM101W only)
20-profile encoder simultaneously
UDP / TCP / HTTP / HTTPS protocols selectable
Cam Viewer Three - Central manag ement software supported
1.3 Package Contents
User can find the following items in the package:
Camera unit x 1
Power Adapter x 1
Camera Mount Kit x 1
User’s Manual CD x 1
Quick Installation Guide x 1
External Antenna x 1 (ICA-HM101W o nly)
NOTE:
1. If any of the above items are missing, please contact your dealer immediately.
2. Using the power supply that is not the one included in Internet Camera packet
will cause damage and void the warranty for this product.
6
2. Basic Setup
This chapter provides details of installing and configu ring the Internet Came ra.
2.1 System Requirement
The Internet Camera can be monitoring on all of Windows operating system that suggest with
system requirment below in order to got better video performance.
Network Interface 10/100MBase-TX Ethernet
Monitoring System Recommended for Internet Explorer 6.0 or later
System Hardware · CPU: Pentium 4, 3.6GHz or above
· Memory Size : 1GB or more
· VGA card resolution : 1280 x 1024 or higher
· VGA card memory : 64 M B or above
· Network bandwidth: In D1 resolution mode, minimum upload
bandwidth is 1.5 ~ 2Mbps.
NOTE: 1. The listed information is minimum system requirements only. Actual requirement
will vary depending on the nature of your environment.
2. The ICA-HM101 series can be managed by PLANET IP Wizard II if you want to
configure more detail information and settings of PLANET IP Wizard II software
please refer to the CD-ROM folder “D:\Utility\IPWizardII\setup.exe”, assume D is
your CD-ROM drive.
7
2.2 Physical Description
2.2.1 Terminal Connections
Front View
1
2 White-light LEDs
3 Lens & focus ring User could use this ring to adjust focus manually.
4
5 PIR Sensor
6
7
Antenna
(ICA-HM101W only )
Microphone
Micro SD Card Slot
Speaker
User can attach the included antenna to antenna connector
(SMA type) or use another high-gain antenna to get higher
performance.
These LEDs are White-light type by mode. It’s very useful for
low-lux environment to provide extra light source for image sensor
The Camera has built in an internal microphone. This microphone is
hidden in the pinhole located on the front panel.
PIR sensor is used to sense motion or detect whether a human
has moved in or out of the sensors range.
User can insert a micro SD card into this slot for event
recording.
The Camera has built in a speaker. This speaker allows to
output voice or alerting sound.
8
2.2.2 Bottom Panel
Audio/Video
1.
Output Jack
ICA-HM101
ICA-HM101W
Audio/Video-out Jack allows this device to output audio and video signal.
Use the attached A/V cabl e to connect A/V device where white cable is for
audio and yellow cable is for video.
2. DC Power Jack
The input power is 12VDC.
Note that supply the power to the Camera with the power adapter
included in package. Otherwise, the improper power adapter may damage
the unit and result in danger.
9
Factory Default
3.
Reset
4 LAN Socket
This button is hidden in the pinhole. This button is used to restore the all
factory default settings. Sometimes restarting the camera will make the
system back to a normal state. If the system still got problems after rest art,
user can restore the factory default settings and install it again. To restore
the device, please follow the steps below:
1. Make sure the Camera is ready first. Insert the paper clip or other tool
and press and hold the button down continuously.
2. Hold it at least 5 seconds and release the tool while the Camera is
operating. Then the device has been restored to default settings and
reboot again.
Note: Restoring the factory default setting will lose the all previous
settings included IP address forever. User needs to run the IPWizard II
program to search the device and configure it to let the device work
properly again.
The LAN socket is a RJ-45 connector for connections to 10Base-T
Ethernet or 100Base-TX Fast Ethernet cabling. This Ethernet port built
N-Way protocol can detect or negotiate the transmission speed of the
network automatically. Please use Category 5 cable to connect the
Network Camera to a 100Mbps Fast Ethernet network switch or hub.
LAN LED
5
(green color)
Power / Wireless
6
7
LED
(orange color)
DI/DO
Connector
This LED is used to indicate whether the camera is ready or not. In
addition, this LED will be flashing while the wireless accessing of the
Camera (WLAN model only).
The Camera has built in a speaker. This speaker allows to output voice or
alerting sound.
The Camera provides a terminal block with 4 pins of connectors for DI and
DO. Please refer to the Appendix A in this manual for more information.
The pin 1 is located at the left side of terminal block from rear view.
10
2.2.3 Side Panel
ICA-HM101/ICA-HM101W
1. Micro-SD Card slot User can insert a micro SD card into this slot for event recording.
11
Hardware Installation
1. Attach the Camera with the included stand
2. Place the Camera on the table or fix it onto ceiling or wall
Use three screws to fix the Network Camera onto the ceiling or wall. You could also put
the Network Camera on the table directly.
Fixed it by
3. Plug an Ethernet cable into the Camera
Connect an Ethernet cable to the LAN socket located on the Network Camera’s bottom and at tach
it to the network.
12
4. Connect the external power supply to Camera
Connect the attached power adapter to the DC power jack of the IP Camera. Note: Use the
power adapter, 12VDC, included in the package and connect it to wall outlet for AC power.
Once you have installed the IP Camera well and powered it on, the network accessing type
LED will turn on. It means the system is booting up successfully. Furthermore, if you have a
proper network connection, and access to the IP Camera, the LED will flash green under wired
mode or orange under wireless mode.
2.3 Initial Utility Installation
This chapter shows how to quick set up your H.264 camera. The camera is with the default
settings. However to help you find the networked camera quickly the windows utility PLANET IP
Wizard II can search the cameras in the network that shall help you to configure some basic
setting before you started advanced management and monitoring.
1. Insert the bundled CD into the CD-ROM drive to launch the auto-run program. Once
completed, a welcome menu screen will appear.
2. Click the “IP Wizard II” hyperlink; you will see the dialog box as below.
13
NOTE:
3. The “Welcome to the InstallShield Wizard for PLANET IP Wizard II” prompt will display on the
screen and click “Next” to continue.
If the welcome screen does not appear, click “Start” at the taskbar. Then, select
“Run” and type “D:\Utility\IPWizard II\setup.exe”, assume D is your CD-ROM drive.
4. Please click “Next” to install with original settings, or you may click “Change…” button to
modify the install folder then press “Next” to continue.
14
5. Please click “Install” to start the installation.
6. Please click “Finish” to complete the installation and launch program immediately.
2.4 Preparation
When you installed the Internet Camera on a LAN environment, you may execute PLANET IP
Wizard II to discover camera’s IP address and set up related parameters in the camera.
2.4.1 Search and View by PLANET IP Wizard II
When you installed the Internet Camera on a LAN environment, you have two easy ways to search
your cameras by PLANET IP Wizard II or UPnP discovery. Here is the way to execute PLANET IP
Wizard II to discover camera’s IP address and set up related parameter in a camera.
15
9 Search
When launch the Planet IP Wizard II, a searching windows will pop up. Planet IP Wizard II is
starting to searching Internet Cameras on the LAN. The existed devices will be listed as below.
16
9 View
If Planet IP Wizard II finds Internet Camera, View button will be available. Please
select the camera you want to view and click the View button. Then you could see
the Video from camera directly. Furthermore you could double click the left button
of mouse to link to the Internet Camera by browser.
2.4.2 Configure Network by PLANET IP Wizard II
In case you want to change the IP related parameters of wired interface, please
select the Internet Camera you want to configure and click the LAN button.
Relative settings will be carried out as below.
17
In case, you do not want to change username and/or password, then just click “Submit” button to
perform your setting accordingly. Click “<<” button will go back to previous page.
If you like to change username and/or password of the device, just click the check button. Then,
the related fields will show up as below.
After keying in new username and password, click “Submit” button to perform your setting
accordingly. Click “<<” button will go back to previous page.
18
2.5 Using UPnP of Windows XP or Vista
2.5.1 Windows XP
UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an UPnP
enabled device. If the operating system, Windows XP, of your PC is UPnP enabled, the device will
be very easy to configure. Use the following steps to enable UPnP settings only if your operating
system of PC is running Windows XP.
NOTE: Please notice that MS Windows 2000 does not support UPnP feature.
Go to Start > Settings, and Click Control Panel.
The “Control Panel” will display on the screen and double click “Add or Remove Programs” to
continue.
The “Add or Remove Programs” will display on the screen and click Add/Remove Widows
Components to continue.
19
The following screen will appear, select “Networking Services” and click “Details” to continue.
The “Networking Services” will display on the screen, select “Universal Plug and Play” and click
“OK” to continue.
20
Please click “Next” to continue.
The program will start installing the UPnP automatically. You will see the below pop-up screen,
please wait while Setup configures the components.
21
Please click “Finish” to complete the UPnP installation
Double-click “My Network Places” on the desktop, the “My Network Places” will display on the
screen and double-click the UPnP icon with Internet Camera to view your device in an internet
browser.
22
ICA-HM101 – 00304f0a145a
2.5.2 Windows Vista
UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an UPnP
enabled device. If the operating system, Windows Vista, of your PC is UPnP enabled, the device
will be very easy to configure. Use the following steps to enable UPnP settings only if your
operating system of PC is running Windows Vista.
Go to Start > Control Panel > Network and Internet > Network and Sharing Center, and turn
on “Network Discovery”.
23
Double-click “My Network Places“ on the desktop, the “My Network Places” will display on the
screen and double-click the UPnP icon with Internet Camera to view your device in an internet
browser.
ICA-HM10 – 00304fA15076
2.6 Setup ActiveX to use the Internet Camera
The Internet Camera web pages communicate with the Internet Camera using an ActiveX control.
The ActiveX control must be downloaded from the Internet Camera and installed on your PC. Your
Internet Explorer security settings must allow for the web page to work correctly. To use the
Internet Camera, user must setup his IE browser as follows:
2.6.1 Internet Explorer 6 for Windows XP
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” ΔCustom Level…”, please
24
setup your “Settings” as follow.
Set the first 3 items
• Download the signed A ctiveX co ntrols
• Download the unsigned ActiveX controls
• Initialize and script the ActiveX controls not masked as safe to Prompt
By now, you have finished your entire PC configuration for Internet Camera.
2.6.2 Internet Explorer 7 for Windows XP
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” ΔCustom Level…”, please
setup your “Settings” as follow.
Set the first 3 items
• Allow previously unused ActiveX control to run…
• Allows Script lets
• Automatic prompting for ActiveX controls
25
By now, you have finished your entire PC configuration for Internet Camera.
2.6.3 Internet Explorer 7 for Windows Vista
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Internet” ΔCustom
Level…”, please setup your “Settings” as follow.
• Enable “Automatic prompting for ActiveX controls”
• Prompt “Initialize and script active controls not marked….”
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Trusted Sites”
ΔCustom Level…”, please setup your “Settings” as follow.
26
• Enable “Automatic prompting for ActiveX controls”
• Prompt “Initialize and script active controls not marked….”
By now, you have finished your entire PC configuration for Internet Camera.
27
3. Web-based Management
This chapter provides setup details of the Internet Camera’s Web-based Interface.
3.1 Introduction
The Internet Camera can be configured with your Web Browser. Before configure, please make
sure your PC is under the same IP segment with Internet Camera.
3.2 Connecting to Internet Camera
z Use the following procedure to establish a connection from your PC to the Internet Camera.
z Once connected, you can add the camera to your Browser’s Favorites or Bookmarks.
Start the web browser on the computer and type the IP address of the camera.
The Default IP: “http://192.168.0.20
“
The login window of Internet Camera will appear,
Default login username/password is: admin / admin
NOTE:
After logged on, you should see the following messages at the top of Internet Explorer:
If the User name and Password have been changed with PLANET IP Wizard II,
please enter the new User name and Password here.
28
Click on the message, and click Install ActiveX Control…
When you see this message, click Install’ to install required ActiveX control
After the ActiveX control was installed and run, the first image will be displayed.
Y ou should b e able to see the images captured from the Internet Camera in the web page now. For
advanced functions, please refer to instructions given in follows chapters.
If you log in the camera as an ordinary user, setting function will be not available. If
NOTE:
you log in the camera as the administrator, you can perform all the settings
provided within the device.
29
Loading...