All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Federal Communication Commission Interference St atement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance. (example-use only shielded interface cables when connecting
to computer or peripheral devices). Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two
conditions: ( 1 ) This device may not cause harmful interference, and ( 2 ) this Device must
accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an un controlled environmen t.
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human
proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
1
However, special attention must be paid to the dangers of electric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer manufacture
must therefore be allowed at all times to ensure the safe use of the equipment
.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may ca use radio interfere nce,
in which case the user may be required to take adequate measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users
of electrical and electronic equipment should understand the meaning of the
crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal
waste and have to collect such WEEE separately.
Revision
User’s Manual for PLANET Wired/Wireless H.264 Mega-Pixel IP Camera
Model: ICA-HM100 / ICA-HM100W
Rev: 1.00 (February. 2010)
Part No. EM-ICAHM100 Series_v1
PLANET has announced a wired/wireless CMOS IR IP camera, ICA-HM100/100W, for meeting
the feedback from worldwide market. The ICA-HM100/100W with built-in high performance
1.3Mega-Pixel CMOS sensor delivers high quality image at maximum 1280x1024 resolutions.
Integrated the next generation video compression technology – H.264, the ICA-HM100/100W can
compress the video size to smaller one for users to transfer the Mega-Pixel image on Internet
easily. Multi-profile stands for video stream simultaneously. The ICA-HM100/100W can generate
H.264 / MPEG-4 and M-JPEG streaming to different users at the same time. It allows up to 20
users to access the ICA-HM100/100W simultaneously. With this state-of-the-art design, the
ICA-HM100/100W is considerable to fit in various network environments.
The ICA-HM100/100W features zero-lux illumination. 6 white LEDs built around the lens bring the
clearest vision at night. The ICA-HM100/100W offers color pictures both in the day and night with
built-in CMOS sensor supporting up to 10 meters. It also uses new High-Light LED to provide
greater performance in the dark and longer life of LED.
Supports S tore-to-NAS fun ction, the ICA-HM100/100W can work a lone and save the video file to a
NAS directly, which can save the PC resource and keep monitoring the environment with motion
detection at 7/24. The ICA-HM100/100W takes surveillance using 2-Way audio. The administrator
can speak to anyone at ICA-HM100/100W remote site with a speaker connected. Compliant with
IEEE 802.3af PoE interface, the ICA-HM100 can be located in places where there are no power
outlets. The ICA-HM100W uses IEEE 802.11N wireless technology that communicates at a
maximum wireless signal rate and security features include WEP and WPA encryption.
The ICA-HM100/100W can be managed by PLANET Cam Viewer Plus, the professional
management software for multi-camera video surveillance application, to provide monitoring,
recording and event management functions. The Cam Viewer Plus enables you to setup a
comprehensive and effective surveillance system quickly and easily. With the ICA-HM100/100W
managed by the Cam Viewer Plus, it provides an enhanced professional security environment to
protect your property and life.
1.1 Overview
This user’s guide explains how to operate this camera from a computer. User should read this
manual completely and carefully before you operate the device
1.2 Features
• 1.3Mega-Pixel CMOS sensor built-in
• 2-Way audio with built-in microphone and can be connected to speaker
• 6 white-light LEDs supporting visible distance up to 10 meter at night
• Multi-profile encoder supports H.264 / MPEG-4 and M-JPEG video compression
simultaneously
• 3GPP for 3G mobile remote applications
• Plug-N-Watch that simplifies system integration in existing network environment
1
• Store-to-NAS function to save video files without operating software
• Easy configuration and management via Windows-based utility or web interface
• DDNS, PPPoE and FTP uploading supports more alternatives in surveillance network
• Motion Detection feature can monitor any suspicious movement in specific area
• Compliant with IEEE 802.3af PoE interface (ICA-HM100)
• IEEE 802.11n(draft 2.0) Wireless LAN Capability (ICA-HM100W)
• Cam Viewer Plus - Central management software supported
1.3 Package Contents
User can find the following items in the package:
Camera unit x 1
Power Adapter x 1
Camera Mount Kit x 1
User’s Manual CD x 1
Quick Installation Guide x 1
External Antenna x 1 (ICA-HM100W o nly)
NOTE:
1. If any of the above items are missing, please contact your dealer immediately.
2. Using the power supply that is not the one included in Internet Camera packet
will cause damage and void the warranty for this product.
2
2. Basic Setup
This chapter provides details of installing and configu ring the Internet Came ra.
2.1 System Requirement
The Internet Camera can be monitoring on all of Windows operating system that suggest with
system requirment below in order to got better video performance.
Network Interface 10/100MBase-TX Ethernet
Monitoring System Recommended for Internet Explorer 6.0 or later
System Hardware · CPU: Pentium 4, 3.0GHz or above
· Network bandwidth: In D1 resolution mode, minimum upload
bandwidth is 1.5 ~ 2Mbps.
NOTE: 1. The listed information is minimum system requirements only. Actual requirement
will vary depending on the nature of your environment.
2. The ICA-HM100 series can be managed by PLANET IP Wizard II if you want to
configure more detail information and settings of PLANET IP Wizard II software
please refer to the CD-ROM folder “D:\ Utility\IPWizard II\setup.exe”, assume D
is your CD-ROM drive.
2.2 Physical Description
2.2.1 Terminal Connections
3
1. Network Accessing
Type LED
2. White-light LEDs
3. Microphone
Front View
Network Accessing
1
2 White-light LEDs
3 Microphone
Type LED
2.2.2 Bottom Panel
1. Audio/Video
Output Jack
2. RJ-45 LAN
Socket
This LED is used to indicate the network type of IP Camera. The
green LED means the IP Camera under wired Ethernet mode (LAN)
and orange LED means Camera under wireless mode (WLAN).
These LEDs are Infra-Red type. It’s very useful for low-lux
environment to provide extra light source for image sensor.
The IP Camera has built-in an internal microphone. This microphone
is hidden in the pinhole located on the front panel.
3. Power Jack
4. Factory
Default Reset
ICA-HM100
4
1.
2.
Audio/Video
Output Jack
RJ-45 LAN
Socket
ICA-HM100W
Audio-out Jack allows this device to output audio or alerting sound.
The LAN socket is a RJ-45 connector for connections to 10/100Base-TX
Fast Ethernet cabling. This Ethernet port built N-Way protocol can detect
or negotiate the transmission speed of the network automatically. Please
use CAT-5 cable to connect the IP camera to a 100Mbps Fast Ethernet
network switch or hub. The ICA-HM100 LAN socket is compliant with
IEEE802.3af standard PoE interface.
3. Power Jack The input power is DC 12V.
This button is used to restore the all factory default settings. Sometimes
restarting the device will make the system back to a normal state.
However, if the system still got problems after rest art, user can rest ore the
factory default settings and install it again.
Factory
4.
Default Reset
Restore the device:
a. Insert the paper clip or other tool and press and hold the
button down continuously.
Hold it at least 5 seconds and release the tool. Then the device has been
restored to default settings and reboot again.
5
2.2.3 Side Panel
1. Micro-SD
Card slot
ICA-HM100
2. Antenna
Connector
ICA-HM100W
1. Micro-SD Card slot User can insert a micro SD card into this slot for event recording.
2. Antenna Connector
In case this Camera is wireless model, there is a connector for
SMA type antenna.
6
2.3 Hardware Installation
Step 1. Attach the Camera with the included stand
Step 2. Place the Camera on the table or fix it onto ceiling or wall
Use three screws to fix the IP Camera onto the ceiling or wall. You could also put the IP
Camera on the table directly.
Fixed it by
Screws
Step 3. Plug an Ethernet cable into the Camera
Connect an Ethernet cable to the LAN socket located on the IP Camera’s bottom and
attach it to the network.
Ethernet Cable
Step 4. Connect the external power supply to Camera
Connect the attached power adapter to the DC power jack of the IP Camera. Note: Use the
power adapter, 12VDC, included in the package and connect it to wall outlet for AC power.
Power Cable
Once you have installed the IP Camera well and powered it on, the network accessing type
LED will turn on. It means the system is booting up successfully. Furthermore, if you have a
7
proper network connection, and access to the IP Camera, the LED will flash green under wired
mode or orange under wireless mode.
NOTE:
1. Only use the power adapter supplied with Internet Camera Otherwise, the
product may be damaged.
2. The power adapter is unnecessary when Internet Camera is connected to a
IEEE802.3af PoE switch. Otherwise, the product may be damaged when
Internet Camera is connected to a PoE switch and power adapter
simultaneously.
2.4 Initial Utility Installation
This chapter shows how to quick set up your H.264 camera. The camera is with the default
settings. However to help you find the networked camera quickly the windows utility PLANET IP
Wizard II can search the cameras in the network that shall help you to configure some basic
setting before you started advanced management and monitoring.
1. Insert the bundled CD into the CD-ROM drive to launch the auto-run program. Once
completed, a welcome menu screen will appear.
2. Click the “IP Wizard II” hyperlink; you will see the dialog box as below.
NOTE:
3. The “Welcome to the InstallShield Wizard for PLANET IP Wizard II” prompt will display on the
screen and click “Next” to continue.
If the welcome screen does not appear, click “Start” at the taskbar. Then, select
“Run” and type “D:\Utility\IPWizard II\setup.exe”, assume D is your CD-ROM drive.
8
4. Please click “Next” to install with original settings, or you may click “Change…” button to
modify the install folder then press “Next” to continue.
5. Please click “Install” to start the installation.
9
6. Please click “Finish” to complete the installation and launch program immediately.
2.5 Preparation
When you installed the Internet Camera on a LAN environment, you may execute PLANET IP
Wizard II to discover camera’s IP address and set up related parameters in the camera.
2.5.1. Search and View by PLANET IP Wizard II
When you installed the Internet Camera on a LAN environment, you have two easy ways to search
your cameras by PLANET IP Wizard II or UPnP discovery. Here is the way to execute PLANET IP
Wizard II to discover camera’s IP address and set up related parameter in a camera.
9Search
When launch the PLANET IP Wizard II, a searching window will pop up. PLANTE IP Wizard II is
starting to search Internet Cameras on the LAN. The existed devices will be listed as below.
10
9View
If PLANET IP Wizard II finds Internet Camera, View button will be available. Please select the
camera you want to view and click the View button. Then you could see the video from camera
directly. Furthermore you could double click the left button of mouse to link to the Internet Camera
by browser.
2.5.2. Configure Network by PLANET IP Wizard II
In case you want to change the IP related pa rameters of wire d inte rface, pl ease select the Inte rnet
Camera you want to configure and click the LAN button. Relative settings will be carried out as
below.
11
You could modify the relative settings of the selected device. Click “<<” button will quit the LAN
setting procedure and click “>>” button will move to next page as below.
In case, you do not want to change username and/or password, then just click “Submit” button to
perform your setting accordingly. Click “<<” button will go back to previous page.
If you like to change username and/or password of the device, just click the check button. Then,
the related fields will show up as below.
12
After keying in new username and password, click “Submit” button to perform your setting
accordingly. Click “<<” button will go back to previous page.
2.6 Using UPnP of Windows XP or Vista
2.6.1. Windows XP
UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an UPnP
enabled device. If the operating system, Windows XP, of your PC is UPnP enabled, the device will
be very easy to configure. Use the following steps to enable UPnP settings only if your operating
system of PC is running Windows XP.
NOTE: Please notice that MS Windows 2000 does not support UPnP feature.
Go to Start > Settings, and Click Control Panel.
13
The “Control Panel” will display on the screen and double click “Add or Remove Programs” to
continue.
The “Add or Remove Programs” will display on the screen and click Add/Remove WidowsComponents to continue.
14
The following screen will appear, select “Networking Services” and click “Details” to continue.
The “Networking Services” will display on the screen, select “Universal Plug and Play” and click
“OK” to continue.
15
Please click “Next” to continue.
The program will start installing the UPnP automatically. You will see the below pop-up screen,
please wait while Setup configures the components.
16
Please click “Finish” to complete the UPnP installation
Double-click “My Network Places” on the desktop, the “My Network Places” will display on the
screen and double-click the UPnP icon with Internet Camera to view your device in an internet
browser.
17
ICA-HM100 – 00304f0a145a
2.6.2. Windows Vista
UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an UPnP
enabled device. If the operating system, Windows Vista, of your PC is UPnP enabled, the device
will be very easy to configure. Use the following steps to enable UPnP settings only if your
operating system of PC is running Windows Vista.
Go to Start > Control Panel > Network and Internet > Network and Sharing Center, and turn
on “Network Discovery”.
18
Double-click “My Network Places“ on the desktop, the “My Network Places” will display on the
screen and double-click the UPnP icon with Internet Camera to view your device in an internet
browser.
ICA-HM100 – 00304fA15076
2.7 Setup ActiveX to use the Internet Camera
The Internet Camera web pages communicate with the Internet Camera using an ActiveX control.
The ActiveX control must be downloaded from the Internet Camera and installed on your PC. Your
Internet Explorer security settings must allow for the web page to work correctly. To use the
Internet Camera, user must setup his IE browser as follows:
2.7.1. Internet Explorer 6 for Windows XP
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” ΔCustom Level…”, please
19
setup your “Settings” as follow.
Set the first 3 items
• Download the signed A ctiveX controls
• Download the unsigned ActiveX controls
• Initialize and script the ActiveX controls not masked as safe to Prom pt
By now, you have finished your entire PC configuration for Internet Camera.
2.7.2. Internet Explorer 7 for Windows XP
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” ΔCustom Level…”, please
setup your “Settings” as follow.
Set the first 3 items
• Allow previously unused ActiveX control to run…
• Allows Script lets
• Automatic prompting for ActiveX controls
20
By now, you have finished your entire PC configuration for Internet Camera.
2.7.3. Internet Explorer 7 for Windows Vista
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Internet” ΔCustom
Level…”, please setup your “Settings” as follow.
• Enable “Automatic prompting for ActiveX controls”
• Prompt “Initialize and script active controls not marked….”
From your IE browse Î ”Tools” Î ”Internet Options…” Î ”Security” Î ”Trusted Sites”
ΔCustom Level…”, please setup your “Settings” as follow.
21
• Enable “Automatic prompting for ActiveX controls”
• Prompt “Initialize and script active controls not marked….”
By now, you have finished your entire PC configuration for Internet Camera.
22
Loading...
+ 61 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.