Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Copyright
Copyright © 2015 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any
software described in this manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the
software. Further, PLANET reserves the right to revise this publication and to make changes from time to
time in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered
trademarks of their respective holders.
Federal Communication Commission Interference St atement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environme nt. In order to
avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna
shall not be less than 20 cm (8 inches) during normal operation.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment. All gui deline s of this and of the co mputer manufacture mu st therefore be a llowed at al l
times to ensure the safe use of the equipment
.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
- 2 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed-out wh eeled bin symbol. Do
not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
User’s Manual of PLANET Z-Wave Ceiling-mount Smoke Detector
Model: HZS-300
Rev: 1.00 (October, 201 5)
Part No. EM-HZS-300 Series_v1.0.doc
- 3 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Table of Contents
Chapter 1. Product Introduction......................................................................5
1.1 Package Contents ..............................................................................5
1.2 Overview.............................................................................................5
1.3 Specifications......................................................................................7
Chapter 2. Hardware Interface........................................................................8
Chapter 3. Z-Wave Device Setting ...............................................................10
3.1 Configuring Z-Wave Device via HAC-1000.......................................10
3.2 Configuring Z-Wave via Smart Phone...............................................14
3.3 Configuring Z-Wave via HTS-1000P.................................................23
Appendix A: Troubleshooting & Frequently Asked Questions.......................31
- 4 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Chapter 1. Product Introduction
1.1 Package Contents
The package should contain the following:
z 4-in-1 Sensor x 1
z Quick Installation Guide x 1
z AAA Battery x 2
z Accessory Bag x 1
If any of the above items are missing, please contact your seller immediately.
1.2 Overview
Home Automation and Smart Home Control
The HZS (Z-Wave Sensing Device) series of PLANET Home Automation product family, based on Z-Wave
technology, provides the advanced security system that protects your home and family 24/7. Easy operation
and flexible configuration are the attractive features of our system; the simple one-touch button lets you
program your regular settings according to your preference and operation mode. Worked with PLANET
HAC-1000 Z-Wave Home Automation Control Gateway, you get the all-round and reliable home security
services that we offer. Our full range of product lines ensure that you get all the devices you need for your
home security system.
Safeguarding Homes Conveniently via the Multi-functional Sensor
PLANET HZS-300, a Z-Wave 4-in-1 Multi Sensor, has four sensors integrated into one device, thus enabling
you to monitor the security of doors and windows, humidifiers, lightings, and thermostats of your home at site
or remotely. The HZS-300 sends Z-Wave signal to the user when someone is prying a door or window open,
- 5 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
or there is a change in humidity, luminosity and temperature. It not only helps to protect homes, offices and
other establishments from theft, but also helps to keep humidity, luminosity and temperature in these places
within their ideal range.
Mini Design for Easy Installation
As the HZS-300 Z-Wave sensor comes in lightweight and compact size, it can be installed on any door and
window in less than 60 seconds. It is also hardly visible to intruders as its size is miniature.
- 6 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Getting Started is as Easy as 1-2-3
1. Via the Cloud Home App (including Home Automation Controller Pad and Control Gateway): Press
Inclusion/Exclusion to include/exclude Z-Wave device.
2. On the Z-Wave device: Press the Pair button to establish a connection with the control gateway.
3. Users can enjoy and manage Z-Wave network right a way.
1.3 Specifications
Product
Feature Specifications
Z-Wave Frequency
Sensor
Temperature Detection Range
Illumination Range
Humidity Range
LED Indicators
Operating Range
Installation
Hardware Specifications
Power Requirements
HZS-300A HZS-300E
America: 908.42MHz Europe: 868.42MHz
Door and window
Illumination
Temperature
Humidity
-40 ~ 105° C
Photoresistor, 0V~1.148V (0%~100%)
0%~100%
Opening/Closing the door/window
Tamper switch
Temperature change
Up to 30 meters in open space
Wall mount, indoor use only
AAA battery, 1.5V
Operating Temperature
Operating Humidity
Weight
Dimensions (W x D x H)
Emission
-15 ~ 60 degrees C
0 ~ 95% (non-condensing)
40g
69 x 28 x 19 mm
CE, FCC
- 7 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Chapter 2. Hardware Interface
Model HZS-300E/HZS-300A
Dimensions (W x D x H) 69 x 28 x 19 mm
Weight 40g (gross weight)
¾ Front Panel
LED/Test/Program Switch
LED
Sensor
Interface Description
Opening/Closing the door/window
Tamper switch
Temperature changed
Temperature LED Color
Under 15°C Green
LED
Sensor
*For more details on indicator, please refer to HZS-300 user manual.*
The sensor is for illumination detection.
15~23°C Blue
23~28°C Yellow
28~36°C Orange
Over 36°C Red
- 8 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
¾ Bottom
Program Switch
- 9 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Chapter 3. Z-Wave Device Setting
3.1 Configuring Z-Wave Device via HAC-1000
Please refer to the following steps to add Z-Wave device via HAC-1000 web.
1. The default username and password are both admin.
2. Click Z-Wave.
3. Click Z-Wave.
- 10 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
4. Click Device Configuration.
Step 1. Include a Z-Wave device via web.
a) Go to "Z-Wave" and click "Device
Configuration".
b) Click” Include New Device” and the
screen will appear with "Add Device:
Waiting for a user action."
c) The distance between HZS-300 and
HAC-1000 is suggested to be in one
meter. Press the program switch of
HZS-300 at least for 1 second to be
included.
d) If your device has succes sfully been added, it will show "Add Device: Command has
been completed successfully".
If the device didn’t add successfully, please place the device next to the
gateway and try again.
- 11 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 2. Set up the location and room for Z-Wave device via HAC-1000 web.
a. Create rooms in your environment.
b. Edit device.
Step 3. Create a scene via web.
a. Click “Create Scene” and name new scene.
- 12 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
b. Select a device from this scene.
c. Select ON or OFF from this scene.
d. You can click “RUN” to run this scene.
- 13 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 4. Create trigger via web.
a. Click “Create a Trigger” and name new
trigger.
b. Select a Z-Wave device for this trigger.
c. Select when it triggers, it will alarm or
bypass.
d. Select when it triggers, it will run which
scene.
After entering the time selected for the scene to trigger, tick “Save and send alarm
notification”. Tick “Active” to enable this trigger.
3.2 Configuring Z-Wave via Smart Phone
The HAC-1100 can be used on iOS and Android operating system. Cloud Home can be downloaded at
Google Play store or app store.
Please refer to the following steps to install Cloud Home app and add Z-Wave device via smart phone.
- 14 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 1. Include a Z-Wave device via smart phone (Android/iOS).
a. Register a user account.
b. Setting
c. Inclusion/Exclusion
d. Click Inclusion to add device.
- 15 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
e. The distance between HZS-300 and
HAC-1000 is suggested to be in one
meter. Press the program switch 3
times within 3 seconds to be
included.
- 16 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 2. Set up the location and room for Z-Wave device.
a. Create rooms in your environment.
b. Click “No Room” to show the device.
And place the new device in a room.
c. Select “Name” to name this device
and select “Location” to place this
device in the room that you created.
d. Select Picture for your Z-Wave
device.
- 17 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
e. Click “Back” to save.
f. Done successfully.
- 18 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 3. Create a scene via smart phone.
a. Click “Add” and name a new scene.
b. Click “Add” to add a Z-Wave device.
c. Select a Z-Wave device.
d. Click ON or OFF for the device you
select.
- 19 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
e. Click “Back” to save.
f. Done successfully.
- 20 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 4. Create Trigger via smart phone.
a. Click “Add”.
b. Name this new Trigger.
c. Select the Z-Wave device and click
next.
d. Select a mode for a Z-Wave device.
e. Select a scene.
f. Select the time for the trigger and
which scene to run.
- 21 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
g. Done successfully.
h. If you enable Save and send alarm
notification, when it triggers, it will
have a log. You can check this in
Notification History.
- 22 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
3.3 Configuring Z-Wave via HTS-1000P
Step 1. Fill out the IP of control gateway to connect with gateway.
Click the “Gateway” button.
Click the magnifying glass
to search the IP of gateway.
Control pad found an IP of
gateway. Click the IP to
join.
The default gateway port is
5000, and user name and
password are both admin.
- 23 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 2. Include a Z-Wave device via HTS-1000P.
Click the “Z-Wave devices”
button to add Z-Wave
devices to gateway.
Click the “Include New
Device” button to add
Z-Wave device.
When you see the message
“Waiting for user action”, you
can press the match button
on Z-Wave devices.
- 24 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
The distance between
HZS-300 and HAC-1000 is
suggested to be in one
meter. Press the program
switch 3 times within 3
seconds to be included.
If a device is added
successfully, it will show the
message: Command has
completed successfully in
device No. XX.
Click the “Exclude Device”
button to exclude Z-Wave
device.
When you see the message
“Waiting for user action”, you
can press the match button
on Z-Wave devices to
exclude device.
- 25 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 3. After including Z-Wave devices in gateway, you can create different scenes with this function. You can
set scenes to control your devices in Scene mode.
Click the “Scene” button.
Click “Create Scene” and
name the new scene.
Select one device to add to
the device list.
Select one device.
- 26 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Click the “Plus” button to
add device.
Select the status of device
(ON or OFF).
Click “All Scenes” to check
the scene.
Step 4. In Trigger mode, the trigger time is set. An alarm notification is sent via sensor. If a sensor is not
installed, this step can be skipped.
Click the “Trigger” button.
- 27 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Click “Create Trigger”.
Trigger: Name this trigger.
Device: Select a Z-Wave device.
Mode: Select “Arm” to enable alarm.
Scene: When it triggers, the fan will
turn on.
Optional: After triggering for 5
seconds, the fan will turn off by itself.
Switch to “AWAY” to enable monitor
mode.
When one of Z-Wave devices is
triggered, control pad will alarm.
- 28 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Step 5. After configuring this part, you can control Z-Wave devi ce s and scenes via control pad.
Click the “Control Panel” button.
Click the three-line button on the
upper right corner and click “Add
Panel”.
There are two types of panel that
you can choose from.
Name the panel.
- 29 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Click and hold for two seconds to
select the device or scene.
Click on the Device field.
Go back to the main page and
click the “Control” button.
You can control scenes and
devices here.
- 30 -
Z-Wave 4-in-1 Multi Sensor
HZS-300E/HZS-300A
Appendix A: Troubleshooting & Frequently Asked
Questions
Features
z The frequency is different between Z-Wave and ZigBee. ZigBee
This difference between Z-Wave
and ZigBee
How to reset the HZS-300 Series
is 2.4GHz and Z-Wave is about 900MHz.
z The outdoor distance is different. ZigBee is 10~75 meters and
Z-Wave is about 30 meters.
Z-Wave Device Installation
Open the rear cover to send the Alarm Report and then press the
program switch 10 times in 10 seconds to enable the HZS-300 to
send the “Device Reset Locally” command and reset to the factory
default.
Only HZS-530 Series can extend the frequency range of Z-Wave.
Repeater Function
HZS-530 Series can act as a signal repeater to enhance the Z-Wave
wireless communication range. For example, the HAC-1000 (Cont rol
gateway) is installed on the second floor to control over the HZS-300
(4-in-1 Sensor) on the first floor, but the Z-Wave frequency is weak.
Thus, HZS-530 Series can be installed in between the second floor
and the first floor to solve the problem.
- 31 -
Loading...