PLANET HPOE-460 User Manual

1. Introduction

1234

4-Port High Power PoE Injector Hub

IEEE 802.3at

52V~56V DC

PWR123

PoE in-Use

1 2 3 4

DATA & PWR

Remove “DATA & PWR” Connection before power on.

CAUTION

DATA

1.1 Checklist

Thank you for purchasing our HPOE-460 4-Port Gigabit IEEE 802.3at High Power over Ethernet Injector Hub, the High Power over Ethernet Injector Hub package shall contains following contents:

Check the contents of your package for following parts:

 High Power over Ethernet Injector Hub x 1

 User's Manual x 1

 Power Adapter x 1

 Power Cord x 1

If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.

1.3 Features

8-Port RJ-45

4-Port 10/100/1000Mbps “Data input”

4-Port 10/100/1000Mbps “Data + Power output”

Power over Ethernet

IEEE 802.3at and IEEE 802.3af Power over Ethernet

Mid-Span PSE

Up to 4 IEEE 802.3at / 802.3af devices powered

DC 52V power over RJ-45 Ethernet cable to devices

with Ethernet port

PoE power up to 30.8 Watts (802.3at PoE) / 15.4

Watts (802.3af PoE) for each PoE ports

Remote power feeding up to 100m

Full power support for per PoE port

Automatically detect powered device (PD)

Circuit protection prevents power interference

between ports

1.4 Specication

Product HPOE-460

Hardware

“Data” Input Ports 4 x RJ-45

Interface

Data Rate 10/100/1000Mbps

LED

Network Cable

Dimension (H x W x D) 26 x 70 x 97mm

Weight 220g

Power Requirement DC 52V~56V

Power over Ethernet

PoE Power Supply Type Mid-Span

PoE Power Output

“Data+Power” Output Ports

4 x RJ-45

System: Power x 1 (Green) Per PoE Port: PoE ready / in-use x 4 (Green)

10Base-T: 2-Pair UTP Cat. 5 up to 100m (328ft) 100Base-TX: 2-Pair UTP Cat. 5 up to 100m (328ft) 1000Base-T: 4-Pair UTP Cat. 5e, 6, up to 100m (328ft) EIA/TIA-568 100-ohm STP (100m, 328ft)

IEEE 802.3af Per Port DC 52V 15.4 Watts IEEE 802.3at Per Port DC 52V 30.8 Watts

1.5 Product Outlook

LED Denition:

LED Color Function

Power Green

PoE Ready / In-Use

Green

Lights to indicate that the HPOE-460 has power.

Lights to indicate the port is providing 52V DC in-line power.

- 1 -

1.2 About the Power over Ethernet Injector Hub

The PLANET HPOE-460 is the next generation 4-Port Gigabit IEEE 802.3at High Power PoE injector Hub, features both IEEE 802.3af and High Power IEEE

802.3at Power over Ethernet (PoE) that combines up

to 30 Watts power output and data per port over one

CAT 5E / 6 Ethernet cable. It is designed specically to

satisfy the growing demand of higher power consuming network PD (powered devices) such as PTZ (Pan, Tilt & Zoom) / Speed Dome network cameras, multi-channel (802.11a/b/g/n) wireless LAN access points and other network devices by providing double amount of PoE power than conventional 802.3af PoE PSE.

The HPOE-460 is installed between a regular Ethernet Switch and the powered devices; it injects power to the PDs without affecting data transmission performance. It offers a cost effective and quick solution to upgrade network system to IEEE 802.3af / IEEE 802.3at Power over Ethernet system without replacing the existing Ethernet Switch. There are 8 RJ-45 STP ports on the front panel of the HPOE-460, half of the ports on right panel function as “Data input" and the other half on left panel function as "PoE (Data and Power) output". The 4 "PoE (Data and Power) output” ports are also the power injectors that transmit DC voltage to the CAT. 5/5e/6 cable and transfer data and power simultaneously between the Injectors and Splitters.

- 2 -

- 3 -

Hardware

Desktop palm size, wall mountable

LED indicator power input indication

FCC Part 15 Class B, CE

100~240V AC, 50/60Hz, 2A universal power supply

adapter with DC 52V / 2.31A power output

 Plug & play

Standard Compliance

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX

IEEE 802.3ab 1000Base-T

 IEEE 802.3af Power over Ethernet

 IEEE 802.3at Power over Ethernet Enhancement

- 4 -

- 5 -

Power Pin Assignment 4/5(+), 7/8(-)

PoE Power Budget 120 Watts

Number of 802.3af PD Class 0, 1, 2, 3 can be powered

Number of 802.3at PD Class 1, 2, 3 can be powered

Number of 802.3at PD Class 0, 4 can be powered

Standards Conformance

IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet

Standards Compliance

IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Enhancement

Regulation Compliance FCC Part 15 Class B, CE

Environment

Operating Temperature 0 ~ 50 Degree C

Storage Temperature -10 ~ 70 Degree C

Humidity 5 ~ 95% (Non-condensing)

- 6 -

- 7 -

2. Hardware Installation

This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same device and automatically distinguishes the speed of incoming connection.

This section describes the hardware features of HPOE-

460. Before connecting any network device to the HPOE460, read this chapter carefully.

2.1. Before Installation

Before your installation, it is recommended to check your network environment. If there has any IEEE

802.3af / 802.3at device which needs power on, the HPOE-460 provides you a way to supply power for this Ethernet device conveniently and easily. The HPOE-460 equips with an AC-DC adapter with DC 52V input and injects this DC power into the pin of the twisted pair cable (pair 4, 5 and pair 7, 8).

If there is very difcult to nd a power socket for AC-DC

Adapter of your Non-IEEE 802.3af / 802.3at networked device, the HPOE-460 and POE-162S / IPOE-162S can provide you a way to supply DC power for this Ethernet device conveniently and easily.

The 10Mbps or 100Mbps and 1000Mbps speed, duplex mode from Data port of HPOE-460 depends on which Ethernet device attached.

- 8 -

2.2 HPOE-460 and POE-162S, the IEEE

Power Line (DC)

Power Line

1000Base-T UTP

PoE

1000Base-T UTP with PoE

8-Port Gigabit Switch

HPOE-460

802.3at PoE

PTZ / Speed Dome

IP Camera

30W

802.3af PoE IP Camera

15W

802.3at PoE Splitter+ Non-PoE Device

802.3at PoE Splitter

802.3at PoE Multi-Channel / High Power

Wireless AP

30W

PoE

Powe r

Note

Straight Cable

SIDE 1

SIDE 2

SIDE 1

SIDE 2

112233445566778

12345678

SIDE 2

Crossover Cable

SIDE 1 SIDE 2

1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown

1 = White/Green 2 = Green 3 = White/Orange 4 = Blue 5 = White/Blue 6 = Orange 7 = White/Brown 8 = Brown

802.3at Injector / Splitter and Equipment Installation

For the places hard to nd the power inlet, the

HPOE-460 and IEEE 802.3at High Power over Ethernet Splitter (POE-162S / IPOE-162S) provides the easiest way to power your Ethernet devices such as IP Camera on the ceiling and the Wireless Access Point installed on the top of the building. With 4 10/100/1000Base-T Gigabit Ethernet ports, the HPOE-460 supports full 52V DC power for any remote IEEE 802.3af / 802.3at powered device (PD).

To control the power system of your networking devices, the HPOE-460 can directly co-work with PoE IP phone to

build VoIP telephony network in the ofce. Furthermore,

the HPOE-460 can be directly connected to any third party IEEE 802.3af / 802.3at compliant devices installed 100 meters away.

3. Troubleshooting

This chapter contains information to help you solve issue. If the High Power over Ethernet Injector Hub is not functioning properly, make sure the High Power over Ethernet Injector Hub was set up according to instructions in this manual.

How to let my Non IEEE 802.3af / 802.3at network devices work with HPOE-460?

Solution:

You can use PLANET Power over Ethernet Splitter, such as PLANET POE-162S / IPOE-162S to work as a power transformer between HPOE-460 and Non IEEE 802.3af /

802.3at devices. The POE-162S and IPOE-162S provide 12V DC and 24V DC voltage output through DIP switch.

The HPOE-460 PoE LED is not light

Solution:

Check the cable connection between HPOE-460 and IEEE

802.3af / 802.3at devices.

- 9 -

Figure 2-1: HPOE-460 Application Topology

1. According to IEEE 802.3af and IEEE

802.3at standard, the HPOE-460 will not inject power to the cable if not connect to IEEE 802.3af and IEEE 802.3at standard devices.

2. Due to the capability of IEEE 802.3af and IEEE 802.3at standard, the HPOE460 can directly connect with any IEEE 802.3af or IEEE 802.3at standard compliant end-nodes.

- 10 -

- 11 -

Why can not power my PoE device on when connect with HPOE-460?

Solution:

1. Please check the cable type of the connection from HPOE-460 to the other end. The cable should be an 8-wire UTP, Category 5/5e/6, EIA568 cable within 100 meters. A cable with only 4-wire, short loop or over 100 meters, all will affect the power supply.

2. Please check and assure the device that fully complied with IEEE 802.3af and IEEE 802.3at standard.

- 12 - - 13 - - 14 -

Appendix A Networking Connection

RJ-45 Pin Assignments

1000Mbps, 1000Base-T

RJ-45 Connector pin assignment

Contact MDI MDI-X

1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD6 BI_DB- BI_DA7 BI_DD+ BI_DC+ 8 BI_DD- BI_DC-

Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard.

10/100Mbps, 10/100Base-TX

RJ-45 Connector pin assignment

Contact

MDI MDI-X Media

Dependant Interface

1 Tx + (transmit) Rx + (receive) 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit)

4, 5 IEEE 802.3af / 802.3at DC 48V / 52V

6 Rx - (receive) Tx - (transmit)

7, 8 IEEE 802.3af / 802.3at DC 0V

MDI-X Media Dependant

Interface -Cross

The standard RJ-45 receptacle / connector

There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection:

Figure A-1: Straight-Through and Crossover Cable

Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network.

Energy Saving Note of the Device

This power required device does not support Standby mode operation. For energy saving, please remove the power cable to disconnect the device from the power circuit. Without removing power cable, the device wills still consuming power from the power source. In the view of Saving the Energy and reduce the unnecessary power consuming, it is strongly suggested to remove the power connection for the device if this device is not intended to be active.