Planet GTP-805A User Manual

1. Product Features

Gigabit Ethernet 802.3at PoE+ Media Converter:

 Interface

z RJ45 interface with Data + Power output

z LC ber optic slot

z 52~56V DC power input socket

 PoE

z Complies with IEEE 802.3af and IEEE 802.3at standard,

end-span PSE

z Provides 52~56V DC power over RJ45 Ethernet cable to

devices with Ethernet port

z Supports PoE power up to 30 watts for PoE port

z Auto detects IEEE 802.3at/IEEE 802.3af PoE equipment,

protecting the devices from being damaged by incorrect
installation

z Remote power feeding up to 100m

z IEEE 802.3at/IEEE 802.3af splitter devices compatibility

2. Checklist

Your GTP-805A carton should contain the following items:

Media Converter x 1 User’s Manual x 1

AC-DC Adapter (Input: 52~56V DC) x 1

If any item is missing or damaged, please consult the dealer
from whom you purchased your Gigabit Ethernet 802.3at PoE+
Media Converter.

The GTP-805A comes with one vacant SFP module
slot. The mini GBIC SFP module is not included in

Note

the package.

Power Information

The power jack of the Gigabit Ethernet 802.3at PoE+ Media
Converter measures 2.1mm in diameter, and comes with
52~56V DC power input. It conforms to the bundled AC-DC
adapter. Should you have the issue of making the power
connection, please contact your local sales representative.

4. Link Fault Pass-through (LFP)

The LFP function includes LLCF and LLR. LLCF and LLR can
immediately alarm administrators the issue of the link media
and provide ecient solution to monitor the network. The LFP
function can be disabled or enabled by the DIP switch.

LLCF means when a device is connected to the converter and
the TP line loses the link, the converter’s ber will disconnect
the transmission link. LLR (Link Loss Return) means when a
device is connected to the converter and the ber line loses
the link, the converter’s ber will disconnect the transmission
link.

LFP function is ON by default setting. If you
are familiar with the network installation and
for diagnostic purpose (i.e. check which end

Note

is broken), you can turn it off and reset the
converter to make it take effect. Otherwise, please
remain it in the default position.

1. It is recommended to use PLANET MFB/MGB
series 100/1000BASE-FX/SX/LX SFP on the GTP­805A. If you insert an SFP transceiver that is not
supported, the GTP-805A will not recognize it.

2. Please check the link-budget of your SFP
transceivers and its physical wiring distance. In

Note

some installation, an in-line optical attenuator
may be required to protect your transceivers.

3. RJ45/STP, UTP Cat5/5e/6, or straight/crossover
cable is accepted; please refer to section 8 for
more about the wiring distance of your TP, optic­fiber networks.

PoE Function

The installation of the GTP-805A and the IEEE 802.3at/802.3af
Injector/Splitter.

Before your installation, it is recommended to check your
network environment. If there is any IEEE 802.3at/802.3af
devices that need to be powered on, the GTP-805A can provide
you with a way to supply power for this Ethernet device
conveniently and easily.

- 1 -

 Hardware

z Metal case

z LED indicators

 Power LED

 PoE-in-use

 Fiber LNK/ACT

 TP LNK/ACT

z DIP switch: LFP (Link Fault Passthrough) mode selection

z 9K maximum frame size supported

z Wall-mount or DIN-rail installation (optional)

- 3 -

3. Product Outlook

Front Panel

There are one RJ45 twisted-pair jack (auto-MDI/MDI-X), one
100/1000X ber-optic SFP slot and four LED indicators.

10/100/1000T

100/1000X

PoE Media Converter
100/1000X to 10/100/1000T

Figure 1: Front Panel of the GTP-805A

Rear Panel

There is one DIP switch for Link Fault Passthrough (LFP)
feature. It is turned on for Link Loss Carry Forward (LLCF)
and Link Loss Return (LLR) detection but this feature is not
operable when turned o. Please refer to the following sections
for more. There is also one DC 52V~56V power socket for the
Gigabit Ethernet 802.3at PoE+ Media Converter.

52-56V

Fiber TX

PWR

PoE­in-Use

LNK/
ACT

OFF

Ethernet+DC

LFP

ON

- 5 -

5. Installing The Converter

To install the GTP-805A, simply complete the following steps:

Ethernet Installation

Step 1: Turn o the power of the device/station in a network

to which the GTP-805A will be attached.

Step 2: Ensure that there is no activity in the network.
Step 3: Attach ber cable from the GTP-805A to the ber

network.

Step 4: Attach a Cat.5/5e/6 UTP cable from the

10/100/1000BASE-T network to the RJ45 port on the
GTP-805A.

Step 5: Connect the 52~56V DC power adapter to the

GTP-805A and verify that the Power LED lights up.

Step 6: Turn on the power of the device/station; the TX Link

and FX Link LEDs should light up when all cables are
attached.

100/1000BASE-X
SFP Transceiver

100/1000BASE-X
LC Fiber

10/100/1000BASE-T UTP

- 7 -

The GTP-805A equips an AC-DC adapter with DC 54V input and
it injects the DC power into the pin of the twisted-pair cable
(Pins 1, 2, 3 and 6).

550m~120km 100 meters

1000

GTP-805A

Fiber Switch

Power DC 52V~56V

DataData

1000

PoE

Power

PoE

Speed Dome

1000BASE-SX/LX Fiber-optic

1000BASE-T UTP with PoE

PoE+

For the places hard to nd the power inlet, the GTP-805A
provides the easiest way to power your powered device such
as an IP camera or wireless access point via PLANET IEEE

802.3at/802.3af Power over Ethernet Splitter (POE-161S/162S)
over a long distance if necessary.

550m~120km 100 meters

GTP-805A

Power DC 52V~56V

Data

PoE

Power

PoE Splitter

DC

IP Camera

Fiber Switch

Data

1000

- 2 -

Figure 2: Rear Panel of the GTP-805A

- 4 -

Figure 3: GTP-805A Installation

- 6 -

- 8 -

1000

1000BASE-SX/LX Fiber-optic

PoE

1000BASE-T UTP with PoE

6. Duplex Mode Support

Taiwan

May 29, 2018

Country

Date

Legal Signature

8. Cable Connection Parameter

The GTP-805A TP port supports triple speed -­10/100/1000BASE-T auto-negotiation. It will auto detect the link
speed and the duplex mode by default with its link partner. The
ber port (100/1000BASE-FX/SX/LX) allows 100/1000Mbps
full duplex by auto-negotiation. Please also check the setting
of the link partner as well.

7. LED Indication

System

LED Color Description

PWR Green Lit indicates the device is powered.

The wiring details are shown below:

Duplex Connection Limitation (max.)

Twisted Pair

Half/Full

Node to Node
Node to Switch/Hub

100 meters

Fiber Optic Cables:

Standard
(Wavelength)

Fiber Type & Cable
Specications

100BASE-FX
(1310nm)

1000BASE-SX
(850nm)

1000BASE-LX
(1310nm)

Multi-mode 50/125μm or 62.5/125μm

Single-mode 9/125μm

9.ProductSpecications

Model GTP-805A

Interface

10/100/1000BASE-T Ethernet TP

Copper Port

SFP Interface 100/1000BASE-X SFP interface

Fiber Mode May vary on SFP Module

interface

Auto-negotiation, auto MDI/MDI-X

with PoE injector function

- 9 -

10/100/1000BASE-T Port

LED Color Function

Indicating that the PoE+ Media

Blink

Converter is actively sending or
receiving data over that port.

LNK/

PoE in

ACT

Use

Green

Orange

Indicating that the port is linked up

Light

at 10/100/1000Mbps.

Indicating that the port is linked

O

down.

Indicating that the port is providing

Light

PoE power to remote powered device.

Indicating that the port is not

O

providing PoE power to remote
powered device.

100/1000BASE-X Fiber Port

LED Color Function

Indicating that the PoE+ Media

Blink

Converter is actively sending or

LNK/

ACT

Green

receiving data over that port.

Light Indicating that the port is linked up.

Indicating that the port is linked

O

down.

- 10 -

- 11 -

Fiber Port Type
(connector)

Fiber Maximum
Distance

SFP, LC type

May vary on SFP Module

Power Over Ethernet

IEEE 802.3af Power over Ethernet

PoE Output

PSE
IEEE 802.3at Power over Ethernet
Plus PSE

Power Output PoE 52~56V DC, 30 watts

PoE Power Supply Type end-span

Power Pin Assignment 1/2 (+), 3/6 (-)

PoE Power Budget 30 watts

Hardware Specications

Switch Architecture Store-and-Forward

Back pressure for half duplex mode

Flow Control

IEEE 802.3x pause frame for full
duplex mode

Maximum Frame Size 9K

System: PWR

LED

Fiber 100/1000BASE-X: LNK/ACT
TP 10/100/1000BASE-T: LNK/ACT
PoE: Power-in-use

x D x

Dimensions (W

H) 70 x 97 x 26 mm

Weight 0.21kg

Power Supply

52~56V DC, external AC-to-DC
adapter

- 12 - - 13 -

Enable: Shut down either TP port or

ber port that is broken

LFP Mode

Disable: Link LED indicators still on if

connection of the other end
is broken

Installation Wall-mount or DIN-rail installation

Standards Conformance

Regulatory Compliance FCC Part 15 Class A, CE

IEEE 802.3 Ethernet
IEEE 802.3u 100BASE-TX/100BASE­FX

IEEE 802.3ab Gigabit Ethernet
Protocols and
Standards Compliance

IEEE 802.3z Gigabit Ethernet over

Fiber Optic

IEEE 802.3x Flow Control

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet

enhancements standard

TP: Cat 5/5e/6 UTP cable

Fiber: Multi-mode: 50/125μm or
Cables

62.5/125μm optic ber

Single-mode: 9/125μm optic

ber

Environment

Temperature 0~50 degrees C

Humidity 5~90% (non-condensing)

1. For connection to the Gigabit Ethernet products,
please refer to the device’s technical manual.

Note

2. Consult your dealer for DIN-rail installation.

EC Declaration of Conformity

I hereby confirm that the following equipment complies with the requirements set out in the
Council Directive on the Approximation of the Laws of the Member States relating to
Electromagnetic Compatibility Directive on (2014/30/EU).

Type of Product:

100/1000BASE-X to 10/100/1000BASE-T PoE+ Media Converter

Model:

GTP-805A

Produced by:

Manufacturer’s Name: Planet Technology Corporation

Manufacturer’s Address: 10F., No.96, Minquan Rd., Xindian Dist.,

For the evaluation regarding the EMC, the following standards were applied:

EN 55032 (2015 + AC:2016)

EN61000-3-2 (2014)

EN61000-3-3 (2013)

EN 55024 (2010 + A1:2015)

EN 55035 (2017)

Person responsible for making this declaration

Name: Kent Kang

Title: Director

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]

New Taipei City 231,Ta iwan , R.O.C.

PLANET TECHNOLOGY CORPORATION

e-mail: [e-mail] http://www.planet.com.tw