Planet GSW-1820HP User guide

Download

Page 1

1. Package Contents

9 11 13 15

1 3 5 7

17 19 21 23

9 11 13 15

1 3 5 7

Standard

Thank you for purchasing PLANET 16-/24-Port 10/100/1000T 802.3at PoE+ Ethernet Switches, GSW-1820HP and GSW-2620HP. “802.3at PoE+ Switches” mentioned in this Guide refers to the GSW-1820HP and GSW-2620HP.

Open the box of the 802.3at PoE+ Switches and carefully unpack it. The box should contain the following items:

The 802.3at PoE+ Switch x 1 User’s Manual x 1 Power Cord x 1

SFP Dust Cap

x 2

Screws x 8

If any of these pieces are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

Rack-mounting

Brackets x 2

Rubber Feet

x 4

 For GSW-2620HP:

- Ports 1 to 22 will isolate respectively.

- Ports 1 to 22 can only communicate with ports 23~24 (uplink ports) and SFP ports 25~26

 Extend mode: Ports 1 to 8 have a data rate of 10Mbps; the

farthest transmission distance up to 250 meters and all ports can communicate with each other.

 The DIP switch can isolate ports to prevent broadcast storm and

defend DHCP spoong

 Automatic address learning and address aging

 Supports Energy-Ecient Ethernet (EEE) function (IEEE 802.3az)

 Hardware

 19-inch rack-mount size, 1U height

 LED indicators for system power, per port PoE ready and PoE

activity, speed, Link/Act

 Ethernet Link Energy-saving technology

- Link down power saving

- Intelligent scale power based on cable length

3.ProductSpecications

Model GSW-1820HP GSW-2620HP

Hardware Specications

10/100/1000BASE-T Copper Ports

802.3af/802.3at PoE+ Injector Ports

1000BASE-X SFP Ports

16 auto-MDI/MDI-X

ports

16 24

2 2

24 auto-MDI/MDI-X

ports

Power over Ethernet

PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE

PoE Power Supply Type

End-span: 1/2 (+), 3/6 (-)

Per port 54V DC, 300mA. max. 15.4 watts

PoE Power Output

(IEEE 802.3af) Per port 54V DC, 600mA. max. 30 watts (IEEE 802.3at)

PoE Power Budget 240 watts

Number of PDs, 7 watts

Number of PDs,

15.4 watts

Number of PDs, 30 watts

16 24

15 15

8 8

Standards Conformance

Regulatory Compliance

FCC Part 15 Class A, CE

IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000BASE-T Standards Compliance

IEEE 802.3z Gigabit SX/LX

IEEE 802.3x ow control and back pressure

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

IEEE 802.3az Energy-Ecient Ethernet

Environment

Operating

Storage

Temperature: 0 ~ 50 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

Temperature: -10 ~ 70 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

 Per 10/100/1000BASE-T Port

LED Color Function

Lights to indicate the link through that port 1000 LNK/ACT

Green

is successfully established at 1000Mbps.

Blinks to indicate that the Switch is actively

sending or receiving data over that port.

Lights to indicate the link through that port 10/100 LNK/ACT

Amber

is successfully established at 10/100Mbps.

Blinks to indicate that the Switch is actively

sending or receiving data over that port.

PoE in Use

Amber

Lights to indicate the port is providing 54V

DC in-line power.

 Per 1000BASE-X SFP Interface

LED Color Function

Lights to indicate the link through that port 1000 LNK/ACT

Green

is successfully established at 1000Mbps.

Blinks to indicate that the Switch is actively

sending or receiving data over that port.

4.3 Multiple Functions of DIP Switch

The front panel of the 802.3at PoE+ Switch provides one DIP switch for Standard, VLAN and Extend mode selections. The detailed descriptions are shown in the following table.

- 1 -

2. Product Features

 Physical Port

 16-/24-port 10/100/1000BASE-T Gigabit RJ45 copper

 2 1000BASE-X SFP slots

 Power over Ethernet

 Complies with IEEE 802.3af/at Power over Ethernet end-span PSE

 Up to 16/24 ports of IEEE 802.3af / 802.3at devices powered

 Supports PoE power up to 30 watts for each PoE port, all power

up to 240W PoE budget.

 Each port supports 54V DC power to PoE powered device

 Auto detects powered device (PD)

 Circuit protection prevents power interference between ports

 Remote power feeding up to 100m in standard mode with 250m in

extend mode

 Switching

 Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/

MDI-X

 Supports IEEE 802.3x ow control for Full-duplex Mode and back-

pressure for Half-duplex Mode

 Integrates address look-up engine, supporting 8K absolute MAC

addresses

 9K jumbo frame supports all speeds (10/100/1000Mbps)

 IEEE 802.1Q VLAN transparency

 Hardware-based DIP switch for Standard, VLAN and Extend

mode selection;

 VLAN mode:

 For GSW-1820HP:

- Ports 1 to 14 will isolate respectively.

- Ports 1 to 14 can only communicate with ports 15~16 (uplink ports) and SFP ports 17~18.

- 3 -

Selectable operation mode

DIP Switch

Dimensions (W x D x H)

Enclosure Metal

Weight 2.55kg 2.79kg

Power Requirements

Power Consumption/ Dissipation

Thermal Fan 2

LED

Switching Specications

Switch Architecture Store-and-Forward

Switch Fabric 36Gbps/non-blocking 52Gbps/non-blocking

Switch Throughput@64bytes

MAC Address Table 8K entries

Jumbo Frame 9216 bytes

Flow Control

 Standard  VLAN  Extend

440 x 208 x 44 mm (1U height)

100~240V AC,

50/60Hz, 3A max.

Max. 275 watts/938 BTU

100~240V AC,

50/60Hz, 3A max.

Max. 282 watts/962 BTU

 System:

Power (Green)

 10/100/1000T RJ45 Interfaces

1000 LNK/ACT (Green), 10/100 LNK/ACT (Amber), PoE (Amber)

 1000X SFP Interfaces

1000 LNK/ACT (Green)

26.8Mpps 38.7Mpps

IEEE 802.3x pause frame for full duplex; back pressure for half duplex

- 5 -

4. Hardware Introduction

4.1 Front Panel

The Front Panel of the 802.3at PoE+ Switch consists of 16/24 autosensing 10/100/1000Mbps Ethernet RJ45 ports. The LED Indicators are also located on the front panel of the 802.3at PoE+ Switch.

16-Port 10/100/1000T 802.3at PoE

PoE-in-Use

GSW-1820HP

24-Port 10/100/1000T 802.3at PoE

PWR

ACTLNK1000 ACTLNK10/100

1 3 5 7 9 11 13 15 17 19 21 23

PoE-in-Use

GSW-2620HP

4.2 LED Indicators

 System

LED Color Function

PWR Green Lights to indicate the Switch has power.

2-Port 1000X SFP Gigabit Ethernet Switch

PWR

ACTLNK1000 ACTLNK10/100

1 3 5 7 9 11 13 15

4 6 8 10 12 141718

PoE-in-Use

ACTLNK1000

162

Standard

VLAN Extend

Figure 4-1: GSW-1820HP Switch Front Panel

2-Port 1000X SFP Gigabit Ethernet Switch

4 6 8 10 12 14 16 18 20 22 242526

ACTLNK1000

Standard

VLAN

2 4 6 8

Extend

Figure 4-2: GSW-2620HP Switch Front Panel

2 4 6 8

10 12 14 16

18 20 22 24

17 18

- 7 -

DIP Switch Mode Function

This mode makes the 802.3at PoE+ Switch operate as a general switch and all PoE

VLAN

Extend

Standard

VLAN

Extend

VLAN

Extend

Note

Please adjust the DIP switch before powering on the

802.3at PoE+ Switch.

ports operate at 10/100/1000Mbps autonegotiation. All ports can communicate with one another.

This mode makes the 802.3at PoE+ Switch operate as a VLAN isolation switch and For GSW-1820HP:

1. Ports 1 to 14 will isolate respectively.

2. Ports 1 to 14 can only communicate with ports 15~16 (uplink ports) and SFP ports 17~18.

For GSW-2620HP:

1. Ports 1 to 22 will isolate respectivelyy.

2. Ports 1 to 22 can only communicate with ports 23~24 (uplink ports) and SFP ports 25~26.

This mode makes the 802.3at PoE+ Switch operate as a Long Reach PoE switch and

1. Ports 1 to 8 support farthest transmission distance of up to 250 meters

2. Ports 1 to 8 have a data rate of 10Mbps

3. All ports can communicate with one another.

- 2 -

- 4 -

- 6 -

- 8 -

Page 2

Power

1000BASE-T UTP

NVR

Standard

VLAN

Extend

GSW-1820HP

Standard Mode (default)

Standard

VLAN

Extend

GSW-1820HP

100 meters (328 feet)

VLAN Isolation Mode

Ports 15~16 and SFP Ports 17~18 to Ports 1~14 Access Permitted

PoE

PoE IP Camera

PoE

IP Camera

PoE

IP Camera

PoE

IP Camera

PoE

100BASE-TX UTP with PoE

Ports 1 to 14

Access Denied

100BASE-TX UTP with PoE

5. Hardware Installation

5.1 Rack Mounting

To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the instructions described below.

Step 1: Place your 802.3at PoE+ Switch on a hard at surface, with

the front panel positioned towards your front side.

Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+

Switch with supplied screws attached to the package. Figure 5-1 shows how to attach brackets to one side of the 802.3at PoE+ Switch.

24-Port 10/100/1000T

24-Port 10/100/1000T 802.3at PoE 2-Port Gigabit TP/SFP Combo Ethernet Switch

PWR

802.3at PoE

ACTLNK1000

ACTLNK10/100

PoE-in-Use

2-Port 1000X SFP Gigabit Ethernet Switch

2-Port 10/100/1000T

1 3 5 7 9 11 13 15 17 19 21 23

GSW-2620HP

GSW-2824P

PoE-in-Use

4 6 8 10 12 14 16 18 20 22 24

Figure 5-1: Attaching the Brackets to the 802.3at PoE+ Switch.

1000

LNK/ACT

10/100

LNK/ACT

PWR

1 2

3 4

1 3 5 7

5 6

7 8

910

1112

ACTLNK1000

Standard

VLAN

Standard

Extend

VLAN

PoE-in-Use

Extend

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

2 4 6 8

1314

9 11 13 15

1516

10 12 14 16

1718

1920

2122

17 19 21 23

2324

1000X SFP

18 20 22 24

Extend Mode

Standard

Power

Extend

VLAN

GSW-1820HP

PoE

Ports 1 to 8

250 meters (820 feet)

PoE

PoE IP Camera

10BASE-T UTP with PoE

- 9 -

4.4 Rear Panel

The rear panel of the 802.3at PoE+ Switch indicates an AC power

socket, which accepts input power from 100 to 240V AC, 50-60Hz, 3A.

100-240V , 50/60Hz, 3A max.

Figure 4-3: GSW-1820HP Switch Rear Panel

100-240V , 50/60Hz, 3A max.

Figure 4-4: GSW-2620HP Switch Rear Panel

 AC Power Receptacle

The device is a power-required device, which means it will not work till it is powered. If your networks

Power Notice

should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.

In some areas, installing a surge suppression device may also help to protect your 802.3at PoE+ Switch from being damaged by unregulated surge or current to the 802.3at PoE+ Switch or the power adapter.

You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect

Caution

screws would invalidate the warranty.

Step 3: Secure the brackets tightly.

Step 4: Follow the same steps to attach the second bracket to the

opposite side.

- 11 -

Step 5: After the brackets are attached to the 802.3at PoE+ Switch,

use suitable screws to securely attach the brackets to the rack, as shown in Figure 5-2.

24-Port 10/100/1000T

24-Port 10/100/1000T 802.3at PoE 2-Port Gigabit TP/SFP Combo Ethernet Switch

PWR

802.3at PoE

ACTLNK1000

ACTLNK10/100

PoE-in-Use

2-Port 1000X SFP Gigabit Ethernet Switch

2-Port 10/100/1000T

1 3 5 7 9 11 13 15 17 19 21 23

1000

10/100

PWR

27 6 10

26 5

1 2

3 4

LNK/ACT

1 3 5 7

5 6

LNK/ACT

7 8

910

ACTLNK1000

Standard

VLAN

Standard

Extend

PoE-in-Use

VLAN Extend

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

2 4 6 8

1112

1314

9 11 13 15

1516

1718

1920

2122

17 19 21 23

2324

18 20 22 24

1000X SFP

10 12 14 16

GSW-2620HP

GSW-2824P

PoE-in-Use

4 6 8 10 12 14 16 18 20 22 24

Figure 5-2: Mounting the 802.3at PoE+ Switch in a Rack

Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at

complied PDs and other network devices.

A. Connect one end of a standard network cable to the

10/100/1000BASE-T RJ45 ports on the front panel of the 802.3at PoE+ Switch.

B. Connect the other end of the cable to the network devices such as

printer servers, workstations or routers, etc.

Step 7: Supply power to the 802.3at PoE+ Switch.

A. Connect one end of the power cable to the 802.3at PoE+ Switch.

B. Connect the power plug of the power cable to a standard wall

outlet.

When the 802.3at PoE+ Switch receives power, the power LED should remain solid Green.

5.2 Installing the SFP Transceiver

The sections describe how to insert an SFP transceiver into an SFP slot of the 802.3at PoE+ Switch.

The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the 802.3at PoE+ Switch, as Figure 5-3 shows.

24-Port 10/100/1000T

PWR

802.3at PoE

ACTLNK1000

ACTLNK10/100

PoE-in-Use

2-Port 1000X SFP Gigabit Ethernet Switch

1 3 5 7 9 11 13 15 17 19 21 23

GSW-2620HP

PoE-in-Use

4 6 8 10 12 14 16 18 20 22 24

 Approved PLANET SFP Transceivers

PLANET 802.3at PoE+ Switch supports both single mode and multimode SFP transceivers. The website link of approved PLANET SFP transceivers is shown below: http://www.planet.com.tw/en/product/product.php?id=11027

It is recommended to use PLANET SFP on the 802.3at PoE+ Switch. If you insert an SFP transceiver that is not

Note

supported, the 802.3at PoE+ Switch will not recognize it.

1 3 5 7

ACTLNK1000

Standard

Extend

9 11 13 15

VLAN

2 4 6 8

10 12 14 16

17 19 21 23

18 20 22 24

MGB-Series

SFP Transceiver

LC Fiber Cable

Figure 5-3: Plug In the SFP Transceiver

1. Before we connect the 802.3at PoE+ Switch to the other network device, we have to make sure both sides of the SFP transceivers are with the same media type, for example, 1000BASE-SX to 1000BASESX; 1000BASE-LX to 1000BASE-LX.

2. Check whether the ber-optic cable type matches with the SFP transceiver requirement.

To connect to 1000BASE-SX SFP transceiver, please use the

multi-mode ber cable with one side being the male duplex LC

connector type.

To connect to 1000BASE-LX SFP transceiver, please use the

single-mode ber cable with one side being the male duplex LC

connector type.

Customer Support

Thank you for purchasing PLANET products. You can browse our online

FAQ resource on PLANET Web site rst to check if it could solve your

issue. If you need more support information, please contact PLANET support team.

PLANET online FAQs: https://www.planet.com.tw/en/support/faq

Support team mail address support@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

- 10 -

- 12 - - 13 - - 14 -