PLANET GSW-1601 User Manual

1. Package Contents

9 11 13 151 3 5 7

3. Product Specications

4. Switch Front Panel

5. Switch Rear Panel

Thank you for purchasing PLANET 16/24-Port 10/100/1000Base-T unmanaged Gigabit Ethernet Switch, GSW-1601 / GSW-2401. “Switch” mentioned in this User’s Manual refers to the GSW-1601 / GSW-2401.

Open the box of the Switch and carefully unpack it. The box should contain the following items:

z The Gigabit Ethernet Switch x 1

z User’s Manual x 1

z Power Cord x 1

z Rubber Feet x 4

z Two Rack-mounting Brackets with Attachment Screws x 8

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

Product GSW-1601 GSW-2401

Hardware Specications

Hardware Version 6

10/100/1000Base-T MDI/MDIX Ports

Throughput (packet per second)

16 24

23.8Mpps 35.7Mpps

Switch Fabric 32Gbps 48Gbps

Weight 1.9kg 2kg

Power Consumption / Dissipation

Power Requirements

12 watts / 40 BTU

100~240V AC,

0.3A, 50-60Hz

14 watts / 47 BTU

100~240V AC,

0.5A, 50-60Hz

Dimensions (W x D x H) 440 x 180 x 44mm, 1U height

Switch Processing Scheme

Store-and-Forward

Address Table 8K entries

Jumbo Packet Size 9K

Back pressure for half duplex,

Flow Control

IEEE 802.3x Pause Frame for full duplex

Figures 1 & 2 show the front panels of the GSW-1601 and GSW-2401.

10 12 14 164 6 82

GSW-1601

16-Port Gigabit Ethernet Switch

LNK

2PWR 4 6 8 10 1214 16

1 3 5 7 9 11 1315

1000 10/100

ACT

LNK/ACT

1000

LNK/ACT

1000

Figure 1: GSW-1601 Front Panel

GSW-2401

24-Port Gigabit Ethernet Switch

ACTLNK

2PWR 4 6 8 10 1214 18

1 3 5 7 119 13 171615201922212423

1000 10/100

LNK/ACT

1000

LNK/ACT

1000

10 12 14 16

9 11 13 151 3 5 7

18 20 22 244 6 82

17 19 21 23

Figure 2: GSW-2401 Front Panel

Figures 3 & 4 show the rear panels of the GSW-1601 and GSW-2401.

Figure 3: GSW-1601 Rear Panel

Figure 4: GSW-2401 Rear Panel

1. The device is a power-required device, meaning it will not work till it is powered. If your network should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or

Power Notice

network downtime.

2. In some area, installing a surge suppression device may also help to protect your Gigabit Ethernet Switch from being damaged by unregulated surge or current to the Switch or the power adapter.

- 1 -

2. Product Features

Physical Port

z 16 / 24-Port 10/100/1000Base-T Gigabit Ethernet ports

z Supports auto MDI/MDI-X function

Layer 2 Features

z Complies with IEEE 802.3, 10Base-T, IEEE 802.3u

100Base-TX, IEEE 802.3ab 1000Base-T Ethernet standards

z Features Store-and-Forward mode with wire-speed

ltering and forwarding rates

z Integrated address look-up engine, supporting 8K abso-

lute MAC addresses

z 9K Jumbo packet support

z IEEE 802.1Q VLAN packet transparent support

z IEEE 802.3x ow control for full duplex operation and

backpressure for half duplex operation

z Hardware based 10/100Base-TX, half / full duplex and

1000Base-T full duplex mode, ow control and auto-

negotiation

z Automatic address learning and address aging

z Supports CSMA/CD protocol

Hardware Features

z 100~240V AC, 0.3A, 50~60Hz universal power input

(GSW-1601)

z 100~240V AC, 0.5A, 50~60Hz universal power input

(GSW-2401)

z FCC, CE class A compliant

- 3 -

Temperature

Humidity

Standards Conformance

Regulation Compliance FCC Part 15 Class A, CE

Standards Compliance

Operating: 0~50 degree C Storage: -10~70 degree C

Operating: 5% to 95% (non-condensing) Storage: 5% to 95% (non-condensing)

IEEE 802.3 (Ethernet) IEEE 802.3u (Fast Ethernet) IEEE 802.3ab (Gigabit Ethernet) IEEE 802.3x (Full-Duplex Flow Control)

- 5 -

LED Indicators

GSW-1601 / GSW-2401

System

LED Color Function

PWR Green

Per 10/100/1000Base-T Port

LED Color Function

LNK / ACT Green

1000 Green

Lights to indicate that the Switch has power.

Lights to indicate the link through that port is established successfully. Blinks to indicate that the Switch is actively sending or receiving data over that port.

Lights to indicate the port is running at

1000Mbps. When off, it indicates that the port is operating at 10/100Mbps.

- 7 -

6. Installing the Switch

This part describes how to install your Gigabit Ethernet Switch and make connections to it. Please follow the procedures below:

This Gigabit Ethernet Switch does not need

Note

Desktop Installation

To install the Gigabit Ethernet Switch on the desktop, simply follow these steps:

Step 1: Attach the rubber feet to the recessed areas on

Step 2: Place the Gigabit Ethernet Switch on the desktop

Step 3: Keep enough ventilation space between the Gigabit

Note

software configuration.

the bottom of the Gigabit Ethernet Switch.

near an AC power source.

Ethernet Switch and the surrounding objects.

When choosing a location, please keep in mind the environmental restrictions discussed in Section 3 under Product Specifications.

- 2 -

- 4 -

- 6 -

- 8 -

Step 4: Connect your Gigabit Ethernet Switch to network

devices.

A. Connect one end of a standard network cable

to the 10/100/1000Base-T RJ-45 ports on the front of the Gigabit Ethernet Switch.

B. Connect the other end of the cable to the

network devices such as printer servers, workstations or routers, etc.

Step 5: Supply power to the Gigabit Ethernet Switch.

A. Connect one end of the power cable to the

Gigabit Ethernet Switch.

B. Connect the power plug of the power cable to

a standard wall outlet.

When the Gigabit Ethernet Switch receives power, the Power LED should remain solid Green.

Step 5: After the brackets are attached to the Gigabit

Ethernet Switch, use suitable screws to securely attach the brackets to the rack, as shown in Figure 6.

24-Port Gigabit Ethernet Switch

GSW-2401

ACTLNK

46 8 1012 14 18

LNK/ACT

1000

13 5 7 119 13 17

PWR

LNK/ACT

1000

10/100

1000

10 12 14 16

9 11 13 151 3 5 7

18 20 22 244 6 82

17 19 21 23

Rack Mounting

To install the Gigabit Ethernet Switch in a 19-inch standard rack, follow the instructions described below:

Step 1: Place your Gigabit Ethernet Switch on a hard at

surface, with the front panel positioned towards your front side.

- 9 -

Step 2: Attach a rack-mount bracket to each side of the

Switch with supplied screws attached to the package. Figure 5 shows how to attach brackets to one side of the Gigabit Ethernet Switch.

24-Port Gigabit Ethernet Switch

GSW-2401

Figure 5: Attaching the brackets to the Gigabit Ethernet Switch

You must use the screws supplied with the mounting brackets. Damage caused to the

Caution

parts by using incorrect screws would invalidate your warranty.

Step 3: Secure the brackets tightly.

Step 4: Follow the same steps to attach the second

bracket to the opposite side.

ACTLNK

4 6 8 1012 14 18

LNK/ACT

1000

1 3 5 7 119 13 17

PWR

LNK/ACT

1000

10/100

1000

10 12 14 16

9 11 13 151 3 5 7

18 20 22 244 6 82

17 19 21 23

Figure 6: Mounting the Gigabit Ethernet Switch in a Rack

Step 6: Proceed with Steps 4 and 5 of Desktop Installation

to connect the network cabling and supply power to your Gigabit Ethernet Switch.

- 11 -

Customer Support

Thank you for purchasing PLANET products. You can browse

our online FAQ resource on PLANET Web site rst to check

if it could solve your issue. If you need more support information, please contact PLANET switch support team.

PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=1

Switch support team mail address : support_switch@planet.com.tw

EC Declaration of Conformity

For the following equipment:

*Type of Product : 16/24 -Port 10/100/1000T Gigabit Ethernet Switch *Model Number : GSW-1601, GSW-2401

* Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,

is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC). For the evaluation regarding the EMC, the following standards were applied:

Responsible for marking this declaration if the:

 Manufacturer  Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan

Person responsible for making this declaration

Name, Surname Kent Kang

Position / Title : Product Manager

New Taipei City 231, Taiwan (R.O.C.).

EN 55022 (CLASS A, 2010 / AC:2011) EN 61000-3-2 (2006 + A1:2009 +A2:2009) EN 61000-3-3 (2008) EN 55024 (2010) IEC 61000-4-2 (2008) IEC 61000-4-3 (2006+A1:2007+A2:2010) IEC 61000-4-4 (2012) IEC 61000-4-5 (2005) IEC 61000-4-6 (2013) IEC 61000-4-8 (2009) IEC 61000-4-11 (2004) EN 60950-1 (2006+A11:2009+A1:2010+A12:2011)

(R.O.C.)

- 10 -

Copyright © PLANET Technology Corp. 2014 Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

- 12 - - 13 - - 14 -

Taiwan

Place Date Legal Signature

19 Sep.., 2014

PLANET TECHNOLOGY CORPORATION

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528

e-mail: sales@planet.com.tw http://www.planet.com.tw