Planet GSD-980HP User Manual

1. Package Contents

1 2 3 4 5 6 7 8 9-

Uplink

VLAN

Thank you for purchasing PLANET GSD-908HP 8-Port 10/100/1000T 802.3at PoE + 1-Port 10/100/1000T Desktop Switch. “802.3at PoE+ Switch” mentioned in this Guide refers to the GSD-908HP.

Open the box of the 802.3at PoE+ Switch and carefully unpack it. The box should contain the following items:

The 802.3at PoE+ Switch x 1 User’s Manual x 1

AC to DC Power

Adapter x 1

Power Cord x 1 Rubber Feet x 4

 Switching

 Hardware-based 10/100/1000Mbps auto-negotiation and

auto MDI/MDI-X

 Flow control for full duplex operation and back pressure

for half duplex operation

 Integrates address look-up engine, supporting 2K absolute

MAC addresses

 9K jumbo frame supports all speeds (10/100/1000Mbps)

 IEEE 802.1Q VLAN transparency

 Automatic address learning and address aging

 Solid DIP switch to isolate ports to prevent broadcast

storm and defend DHCP spoong

 Hardware

 Made of metal, desktop size and wall-mount design

 LED indicators for system power, per port PoE-in-Use (Port

1 to port 8), per port Link/Act (10/100/1000Mbps, port 1 to port 9).

 55V DC, 2.3A external power adapter

 FCC, CE Class A compliant

Weight 419g

Power Requirements 55V DC, 2A

Power Consumption/ Dissipation

Max. 100 watts / 341BTU

Power over Ethernet

IEEE 802.3af Power over Ethernet/

PoE Standard

PSE IEEE 802.3at Power over Ethernet Plus/PSE

PoE Power Supply Type

End-span: 1/2 (+), 3/6 (-)

Per port 54V DC, 300mA. max.

PoE Power Output

15.4 watts (IEEE 802.3af)

Per port 54V DC, 600mA. max.

30 watts (IEEE 802.3at)

PoE Power Budget 100 watts

Number of PDs, 7 watts

Number of PDs, 15.4 watts

Number of PDs, 30 watts

4. Hardware Introduction

4.1 Front Panel

The front panel of the 802.3at PoE+ switch consists of 9 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports. The LED indicators are also located on the front panel of the 802.3at PoE+ switch.

GSD-908HP

Figure 4-1: GSD-908HP Switch Front Panel

The front panel of 802.3at PoE+ switch provides one DIP switch for “Default” or “VLAN” mode selection. The detailed descriptions are shown in the following table.

DIP Switch Mode Function

This mode makes the 802.3at PoE+

Default

Switch operate as a general switch and all ports operate at 10/100/1000Mbps autonegotiation.

This mode makes the 802.3at PoE+ Switch operate as a VLAN isolation switch and

VLAN

port 1 to port 8 will isolate respectively. Port 1 to port 8 can only communicate with port 9 (uplink port).

PoE-in-Use ACTLNK

PWR

Default

- 1 -

If any of these pieces are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

2. Product Features

 Physical Port

 9-port 10/100/1000BASE-T Gigabit RJ45 copper

 Power over Ethernet

 Complies with IEEE 802.3at Power over Ethernet Plus

 Complies with IEEE 802.3af Power over Ethernet

 Up to 8 ports of IEEE 802.3af/802.3at devices powered

 Supports PoE Power up to 30.8 watts for each PoE port

 Each port supports 54V DC power to PoE powered device

 100-watt PoE budget

 Auto detects powered device (PD)

 Circuit protection prevents power interference between

ports

 Remote power feeding up to 100m

- 3 -

3.ProductSpecications

Model GSD-908HP

Hardware Specications

10/100/1000BASE-T Copper Ports

802.3af/802.3at PoE+ Injector Port

Switch Architecture Store-and-Forward

Switch Fabric 18Gbps

Switch Throughput@64bytes

MAC Address Table 2K entries

Jumbo Frame 9216 bytes

Flow Control

LED

DIP Switch

Dimensions (W x D x H)

Enclosure Metal

9 auto-MDI/MDI-X ports

13.3Mpps

IEEE 802.3x pause frame for full duplex; back pressure for half duplex

System: Power (Amber) 10/100/1000T RJ45 Interfaces PoE-in-Use (Amber) 10/100/1000 LNK/ACT (Green)

Default mode for switch

architecture

VLAN mode for Port-based VLAN

168 x 94 x 32 mm

Standards Conformance

Regulatory Compliance

Standards Compliance

Environment

Operating

Storage

- 5 -

FCC Part 15 Class A, CE

IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab Gigabit 1000BASE-T

IEEE 802.3x ow control and back

pressure IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus

Temperature: 0 ~ 50 degrees C Relative Humidity: 5 ~ 95% (non-condensing)

Temperature: -10 ~ 70 degrees C Relative Humidity: 5 ~ 95% (non-condensing)

- 7 -

After changing the mode, you need to manually restart the 802.3at PoE+ Switch to make the

Note

corresponding configuration take effect.

4.2 LED Indicators

 System

LED Color Function

PWR Amber Lights to indicate the Switch has power.

 Per 10/100/1000BASE-T Port

LED Color Function

PoE in Use Amber

10/100/1000

LNK/ACT

Green

Lights to indicate the port is providing PoE in-line power.

Lights to indicate the link through that port is successfully established at 10/10/1000Mbps.

Blinks to indicate that the Switch is actively sending or receiving data over that port.

- 2 -

- 4 -

- 6 -

- 8 -

4.3 Rear Panel

The rear panel of the 802.3at PoE+ switch comes with a DC power socket that accepts 55V DC input power and a grounding terminal that protects the 802.3at PoE+ Switch against lightning strikes.

55V DC

Step 4: Connect your 802.3at PoE+ Switch to 802.3af/802.3at

complied powered devices (PD) and other network devices.

A. Connect one end of a standard network cable to

the 10/100/1000 RJ45 ports on the front panel of the 802.3at PoE+ Switch.

B. Connect the other end of the cable to the network

devices such as printer servers, workstations, router, etc.

Figure 4-2: GSD-908HP Switch Rear Panel

 DC Power Receptacle

1. The device is a power-required device, which means it will not work till it is powered. If your networks should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.

Power Notice

2. In some areas, installing a surge suppression device may also help to protect your 802.3at PoE+ Switch from being damaged by unregulated surge or current to the 802.3at PoE+ Switch or the power adapter.

- 9 -

Connection to the 802.3at PoE+ Switch requires UTP Category 6/5e/5 network cabling with RJ45

Note

tips

Step 5: Supply power to the 802.3at PoE+ Switch.

A. Connect one end of the power cable to the DC

power adapter and connect its DC plug connector to the 802.3at PoE+ Switch.

B. Connect the power plug of the power cable to a

standard wall outlet.

When the 802.3at PoE+ Switch receives power, the Power LED should remain solid amber.

- 11 -

5. Hardware Installation

5.1 Desktop Installation

To install the 802.3at PoE+ Switch on desktop, simply follow the steps below:

Step 1: Attach the rubber feet to the recessed areas on the

bottom of the PoE+ Ethernet Switch, as shown in Figure 5-1.

GSD-908HP

1 2 3 4 5 6 7 8 9-

Figure 5-1: Placing the PoE+ Ethernet Switch on the Desktop

Step 2: Place the 802.3at PoE+ Switch on desktop near an AC

power source.

Step 3: Keep enough ventilation space between the 802.3at

PoE+ Switch and the surrounding objects.

PoE-in-Use

LNK

ACT

PWR

Default

Uplink

VLAN

Customer Support

Thank you for purchasing PLANET products. You can browse

our online FAQ resource on PLANET Web site rst to check if it

could solve your issue. If you need more support information, please contact PLANET switch support team.

PLANET online FAQs: https://www.planet.com.tw/en/support/faq

Support team mail address: support@planet.com.tw

EC Declaration of Conformity

For the following equipment:

*Type of Product: 8-Port 10/100/1000Mbps 802.3at PoE + 1-Port 1000Mbps

*Model Number: GSD-908HP

* Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,

is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2014/30/EU and Low Voltage Directive 2014/35/EU.

For the evaluation regarding the EMC, the following standards were applied:

Responsible for marking this declaration if the:

 Manufacturer  Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan

Person responsible for making this declaration

Name, Surname K ent Kang

Position / Title : Director

Desktop Switch

New Taipei City 231, Taiwan R.O.C.

EN 55032 (2012 + AC:2013)

EN 61000-3-2 (2014)

EN 61000-3-3 (2013) EN 55024 (2010) EN60950-1 (2006+A11:2009+A1:2010+A12:2011+A2:2013)

R.O.C.

Note

When choosing a location, please keep in mind the environmental restrictions discussed in Section 3 under Specifications.

- 10 -

Copyright © PLANET Technology Corp. 2020 Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

- 12 -

Taiwan March 25, 2017

Place Date Legal Signature

PLANET TECHNOLOGY CORPORATION

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528

e-mail: sales@planet.com.tw http://www.planet.com.tw