Planet GSD-604HP operation manual
1. Package Contents
Uplink
Check the following contents of your package:
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
GSD-604HP User's Manual 55V Power Adapter
Power Cord Rubber Feet Wall-mount Kit
x 4
Switching
Hardware based 10/100/1000Mbps auto-negotiation
and auto MDI/MDI-X
Flow control for full duplex operation and back
pressure for half duplex operation
9216 bytes jumbo packet size support
Integrates address look-up engine, supporting 8K
absolute MAC addresses
Automatic address learning and address aging
Supports port-based VLAN and loop protection
3. Switch Front Panel
Figure 3-1 shows the front panel of GSD-604HP.
GSD-604HP
PoE
41 2 3 6
1000 LNK
ACT
10/100 LNK
ACT
5
PoE MAX
PoE In-Use
PWR
1 2 3 4
5. Switch Rear Panel
Figure 5-1 shows the rear panel of GSD-604HP.
Please power off before switching DIP.
Power
Notice
Port-based VLAN & Loop protection
Figure 5-1: GSD-604HP Rear Panel
1. The device is a power-required device,
meaning it will not work till it is powered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your
device. It will prevent you from network
data loss or network downtime.
2. In some areas, installing a surge suppression device may also help to protect
your GSD-604HP from being damaged
by unregulated surge or current to the
GSD-604HP or the power adapter
DisableEnable
55V DC
7. Installing the Switch
This part describes how to install your Gigabit PoE+
Switch and make connections to it. Please read the
following topics and follow the procedures as presented.
This Gigabit PoE+ Switch does not need
Note
Desktop Installation
To install the Gigabit PoE+ Switch on desktop, simply
follow the following steps:
Step 1: Attach the rubber feet to the recessed areas
Step 2: Place the Gigabit PoE+ Switch on desktop near
Step 3: Keep enough ventilation space between the
Note
software configuration.
on the bottom of the Gigabit PoE+ Switch.
AC power source for its power adapter.
Gigabit PoE+ Switch and the surrounding
objects.
When choosing a location, please keep in
mind the environmental restrictions discussed in Chapter 8 -- Product Specifications.
- 1 -
2. Product Features
RJ45 Interface
6 10/100/1000Mbps Gigabit Ethernet ports
4 ports support 54V DC power to PoE powered
device
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet
end-span PSE
Up to 4 IEEE 802.3af/802.3at devices powered
Supports PoE power up to 30 watts for each PoE
port
55-watt PoE Budget
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m
Hardware
LED indicators for PoE ready/activity and LINK/ACT
One 55V DC power jack
- 2 -
Figure 3-1: GSD-604HP Front Panel
- 3 -
4. LED Indicators
System
LED Color Function
PWR Green
Per 10/100/1000Mbps Port
LED Color Function
1000
LNK
10/100
LNK
Green
Orange
PoE-in-Use Port
LED Color Function
PoE Orange
MAX Orange
Lights: Indicates the Switch has
power.
Lights: Indicates the link through
that port is successfully
established at 1000Mbps.
Blinks: Indicates that the Switch is
actively sending or receiving
data over that port.
Lights: Indicates the link through
that port is successfully
established at 10/100Mbps.
Blinks: Indicates that the Switch is
actively sending or receiving
data over that port.
Lights: Indicates the port is providing
54V DC in-line power.
Lights: 80% of PoE usage
Blinks: 100% of PoE usage
- 4 -
- 5 -
6. Port-based VLAN and Loop
Protection Feature
The GSD-604HP has one feature called Port-based
VLAN and Loop Protection. When switching the DIP to
the “Enable” position, port 1 to port 5 wouldn’t able to
communicate with each other.
1 2 3 4
GSD-604HP
PoE
5
41 2 3 6
PoE MAX
PoE In-Use
PWR
Port 1 to Port 5 only can communicate with Uplink Port 6.
1 2 3 4
GSD-604HP
PoE
5
41 2 3 6
PoE MAX
PoE In-Use
PWR
When there is a loop happening from the client, the
GSD-604HP will block that port and wouldn’t allow data
to transfer to the switch.
1 2 3 4
GSD-604HP
PoE
Loop (broadcast)
5
41 2 3 6
PoE MAX
PoE In-Use
PWR
- 6 -
1000 LNK
ACT
10/100 LNK
ACT
1000 LNK
ACT
10/100 LNK
ACT
1000 LNK
ACT
10/100 LNK
ACT
Uplink
Uplink
Uplink
Step 4: Connect your Gigabit PoE+ Switch to network
devices.
- 7 -
A. Connect one end of a standard network cable to
port-5 and port-6 10/100/1000Mbps RJ45 ports on
the front of the Gigabit PoE+ Switch.
B. Connect the other end of the cable to the network
devices such as NVR(Network Video Recorder),
workstations or routers.
Step 5: Connect your Gigabit PoE+ Switch to PoE PD
devices.
A. Connect one end of a standard network cable to port
1 to port 4 10/100/1000Mbps RJ45 ports on the
Front of the Gigabit PoE+ Switch.
B. Connect the other end of the cable to the 802.3at/
af powered devices.
Port 1~Port 4 PoE IP Cameras
PoE PoE PoE PoE
PoE
4 Channel NVR
GSD-604HP
Power Line
1000BASE-T UTP
1000BASE-T UTP with PoE
Power
Port 5~Port 6 Dual Uplink Ports
- 8 -
Cable Distance for Switch
The cable distance between the GSD-604HP
Note
Note
Step 6: Supply power to the Gigabit PoE+ Switch.
A. Connect one end of the power cable to the Switch.
B. Connect the power plug of the power cable to a
When the Gigabit PoE+ Switch receives power, the
Power LED should remain solid Green.
and PC/PD devices should not exceed 100
meters for UTP/STP cable.
Make sure the wiring is correct
Category 3/4/5 cable can be used for
10/100Mbps operation. To reliably operate
your network at 1000Mbps, you must use
an Unshielded Twisted-Pair (UTP) Category
5/5e cable, or better data grade cabling.
While a Category 3 or 4 cable may initially
seem to work, it will soon cause data loss.
standard wall outlet.
Wall-mount Installation
Step 1: Please nd the wall that can mount the
GSD-604HP.
Step 2: Install four screws on the wall.
8. Product Specications
GSD-604HP
Model
HardwareSpecications
Network Connector
PoE Inject Port
LED Display
Switch Architecture
Thermal Fan Fanless design
MAC Address Table
Switch Fabric 12Gbps
4-Port 10/100/1000T 802.3at
PoE + 2-Port 10/100/1000T
Desktop Switch
6-Port RJ45 for
10/100/1000BASE-T, auto MDI/
MDIX
4-Port with 802.3af/at PoE
injector function (port 1 to port
4)
System: Power (Green)
Per PoE port:
PoE (Orange, port 1 to port 4)
PoE MAX (Orange)
Ethernet port:
1000 LNK (Green)
10/100 LNK (Orange)
Store and Forward switch
architecture
8K MAC address table with auto
learning function
- 9 -
Step 3: Hang the GSD-604HP on the screws from the
wall.
Step 4: Repeat step 6 of Desktop Installation for
power supply to the GSD-604HP.
Before mounting the device to the wall,
please check the location of the electrical
Note
outlet and the length of the Ethernet cable.
RJ45
UTP Cable
- 11 -
Switch Throughput 8.92Mpps @64 bytes
Jumbo Packet 9216 bytes
Back pressure for half-duplex.
Flow Control
Power Requirements 55V DC, 1.1A
ESD Protection 6KV DC
Power Consumption Max. 60 watts, 204.6 BTU
Dimensions
(W x D x H)
Weight 374g
Power over Ethernet
PoE Standard
PoE Power Supply
Type
Power Pin
Assignment
PoE Power Output
PoE Power Budget 55 watts
IEEE 802.3x pause frame for
full-duplex
160 x 92.5 x 28mm
IEEE 802.3af Power over
Ethernet/PSE
IEEE 802.3at Power over
Ethernet Plus/PSE
End-span
1/2(+), 3/6(-)
Per Port 54V DC, 300mA. max.
15.4 watts (IEEE 802.3af)
Per Port 54V DC, 600mA. max.
30 watts (IEEE 802.3at)
Standard Conformance
EMI Safety FCC Class B, CE
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
Standard
Compliance
Environment
Operating
Environment
Storage
Environment
Operating Humidity
Storage Humidity
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
0 ~ 50 degrees C
-10 ~ 70 degrees C
5 ~ 95%, relative humidity, non-
condensing
5 ~ 95%, relative humidity, non-
condensing
Ethernet
Fast Ethernet
Gigabit Ethernet
Flow Control
Power over
Ethernet
Power over
Ethernet Plus
9. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
support_switch@planet.com.tw
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.
- 10 - - 12 - - 13 - - 14 -
Loading...