Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does not
represent a commitment on the part of PLANET. PLANET assumes no responsibility
for any inaccuracies that may be contained in this User’s Manual. PLANET makes
no commitment to update or keep current the information in this User’s Manual,
and reserves the right to make improvements to this User’s Manual and/or to the
products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from
the power circuit.
Without removing power cable, the device will still consuming power from the
power source. In the view of Saving the Energy and reduce the unnecessary power
consuming, it is strongly suggested to remove the power connection for the device
if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste and have to collect such WEEE
separately.
Check the contents of your package for following parts:
FSD-808HP x 1 l
User's Manual x 1 l
19” Rack Mount Accessory Kit x 1 l
Rubber Feet x 4 l
Power Cord x 1 l
If any of these pieces are missing or damaged, please contact your dealer
immediately, if possible, retain the carton including the original packing material,
and use them against to repack the product in case there is a need to return it to
us for repair.
1.2 Product Description
To fulll the demand of High Power PoE for network applications, the PLANET
802.3at PoE Fast Ethernet Switch family -FSD-808HP is an ideal solution. Each
10/100Mbps port of FSD-808HP features IEEE 802.3af and High Power IEEE
802.3at Power over Ethernet (PoE) that combines up to 140 Watts power output
and data per port over one Cat. 5E / 6 Ethernet cable, with totally 140 Watts PoE
budget on whole system, it is designed specically to satisfy the growing demand
of higher power consuming network PD (powered devices) such as PTZ (Pan, Tilt
& Zoom) / Speed Dome network cameras, multi-channel (802.11a / b / g /
n) wireless LAN access points and other network devices by providing double PoE
power than conventional 802.3af PoE currently.
The 8 10/100Mbps High Power PoE ports in the FSD-808HP supports both 802.3af
and 802.3at PoE standards and allows users exibly connect standard and high
powered devices simultaneously, the FSD-808HP offering 140 Watts PoE budget,
eight 15.4 Watts IEEE 802.3af devices or four 30 Watts IEEE 802.3at devices can
be easily installed without the power-socket limitation.
To facilitate power management, the FSD-808HP equips two orange LEDs hardware
designed that located on left side of FSD-808HP front panel, it call “PoE Power
Usage”. 1-4 is meaning that counting from port 1 to 4 of PoE output and 5-8 is
meaning that counting from port 5 to 8 of PoE output. The 80% is meaning that,
when 1-4 or 5-8 PoE output is over 80%, the LED will be light to advise customers.
With these LED indications, you can monitor current PoE power used status of FSD-
808HP easily and efciently.
Providing data transfer and High Power PoE in one unit, the FSD-808HP shall
reduce the need of extension cables and dedicated electrical outlets on the wall,
5
6
ceiling or any unreachable place. It helps to lower the installation costs and simplify
the installation effort. Besides, the rst important key feature is energy saving.
With more efcient switching power supply, the efciency of the FSD-808HP would
be much better than eight linear power adapters in the long run. Furthermore, it is
the ideal device for bridging among Fast Ethernet and Gigabit Ethernet workgroups
and networks. With Gigabit throughput and eight IEEE 802.3af / 802.3at PoE
interfaces supported, the FSD-808HP is ideal for small business and workgroups
to efciently deploy the High Power PoE network for the wireless access points, IP-
based surveillance camera or IP phones in any places.
All RJ-45 copper interfaces in the FSD-808HP support 10/100Mbps Auto-Negotiation
for optimal speed detection through RJ-45 Category 6, 5 or 5e cables. It also
supports standard Auto-MDI/MDI-X that can detect the type of connection to any
Ethernet device without requiring special straight or crossover cables.
1.3 Features
RJ-45 Interface n
8-Port 10/100Mbps Fast Ethernet ports l
8-Port supports 52V DC power to PoE Powered Device l
Power over Ethernet n
Comply with IEEE 802.3af / IEEE 802.3at Power over Ethernet End-Span PSE l
Up to 8 IEEE 802.3af / IEEE 802.3at devices powered l
Supports PoE Power up to 30 Watts for each PoE port l
Auto detect powered device (PD) l
Circuit protection prevents power interference between ports l
PoE Usage Alarm LED l
Remote power feeding up to 100m l
Switching n
Hardware based 10/100Mbps Auto-Negotiation and Auto MDI/MDI-X l
Flow control for Full Duplex operation and back pressure for Half Duplex oper- l
ation
Integrates address look-up engine, supporting 2K absolute MAC addresses l
Automatic address learning and address aging l
Supports Energy-Efcient Ethernet (EEE) function (IEEE 802.3az) l
Hardware n
12-inch desktop size, 1U height l
LED indicators for PoE ready, PoE activity and PoE Usage Alarm l
Fanless design l
7
1.4 Specication
Model
Hardware Specication
Network Connector8-Port RJ-45 for 10/100Base-TX
PoE Inject Port8-Port with 802.3af / 802.3at PoE injector function
LED Display
Switch ArchitectureStore and Forward switch architecture
MAC Address2K MAC address table with Auto learning function
Power over Ethernet / PSE
Enhancement Power over Ethernet / PSE
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Enhancement Power over Ethernet
Energy-Efcient Ethernet
8
2. Hardware Description
12346785
PoE
1 3 5 74 6 82
PWR
80%
5-8
1-4
ACTLNK
FSD-808HP
8-Port 10/100Mbps 802.3at PoE Ethernet Switch
PoE
Usage
Alarm
This product provides two different running speeds – 10Mbps and 100Mbps in the
same switch and automatically distinguishes the speed of incoming connection.
This section describes the hardware features of FSD-808HP. For easier management
and control of the Switch, familiarize yourself with its display indicators, and
ports. Front panel illustrations in this chapter display the unit LED indicators.
Before connecting any network device to the FSD-808HP, please read this chapter
carefully.
2.1 Front Panel
The Front Panel of the FSD-808HP PoE Ethernet Switch consists of 8x Auto-Sensing
10/100Mbps Ethernet RJ-45 Ports. The LED Indicators are also located on the front
panel of the FSD-808HP.
Figure 2-1: FSD-808HP Switch Front Panel
2.1.1 LED Indicators
System
LEDColorFunction
PWRGreenLight: Indicate the Switch has power.
Per 10/100Mbps Port
LEDColorFunction
PoEGreenLight: Indicate the port is providing 52V DC in-line power.
Light: Indicate the link through that port is successfully
LNK/ACTGreen
established.
Blink: Indicate that the Switch is actively sending or
receiving data over that port.
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.