Planet FSD-504HP operation manual

1. Package Contents

Standard Extend

Standard Extend

Check the following contents of your package:

FSD-504HP User’s Manual

51V Power Adapter Power Cord

If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.

 Switching

 Hardware based 10/100Mbps auto-negotiation and

auto MDI/MDI-X

 Flow control for full duplex operation and back

pressure for half duplex operation

 1536bytes packet size support

 Integrates address look-up engine, supporting 1K

absolute MAC addresses

 Automatic address learning and address aging

 Solid DIP switch to isolate ports to prevent

broadcast storm and defend DHCP spoong

 Hardware

 Desktop palm size

 LED indicators for PoE ready/activity and LINK/ACT

 One DC 51V power jack

Power

Power

FSD-504HP

100 meters/328 feet

Extend PoE Mode

FSD-504HP

250 meters/820 feet

PoE IP Camera

PoE IP Camera

5. Switch Rear Panel

Figure 5-1 shows the rear panel of FSD-504HP.

51V DC

Figure 5-1: FSD-504HP Rear Panel

1. The device is a power-required device,
meaning it will not work till it is pow­ered. If your networks should be active
all the time, please consider using UPS
(Uninterrupted Power Supply) for your

Power
Notice

device. It will prevent you from network
data loss or network downtime.

2. In some area, installing a surge suppres­sion device may also help to protect your
FSD-504HP from being damaged by un­regulated surge or current to the FSD­504HP or the power adapter.

- 1 -

2. Product Features

 RJ45 Interface

 Five 10/100Mbps Fast Ethernet ports

 4 ports support 51V DC power to PoE powered

device

 Power over Ethernet

 Complies with IEEE 802.3af/at Power over Ethernet

end-span + mid-span PSE

 Up to 4 IEEE 802.3af/2 IEEE 802.3at devices

powered

 Supports PoE power up to 30 watts for each PoE

port

 60-watt PoE budget

 Hardware DIP switch for “Standard” and “Extend”

mode selection; the “Extend” mode features
30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation

 Auto detects powered device (PD)

 Circuit protection prevents power interference

between ports

 Remote power feeding up to 100m with standard

mode

- 3 -

3. Switch Front Panel

Figure 3-1 shows the front panel of FSD-504HP.

LNK PoE In-use

ACT

Standard Extend

FSD-504HP

PoE

1 2 3 4 5

Figure 3-1: FSD-504HP Front Panel

The front panel of FSD-504HP provides one DIP switch
for “Standard” and “Extend” mode selections. The
detailed descriptions are shown in the following table.

DIP Switch
Mode

Standard
(default)

This mode makes the FSD-504HP operate
as a general switch and all ports operate
at 10/100Mbps auto-negotiation.

Function

This mode makes the FSD-504HP

operate as a VLAN isolation switch and
port 1 to port 4 will isolate respectively.,
Port 1 to port 4 can only communicate

Extend

with port 5 (uplink port).

This mode also makes the FSD-504HP

operate at auto–negotiation 10Mbps
speed duplex mode only, but the
delivery distance of PoE power and
network data can reach 250m.

PWR

Uplink

- 5 -

4. LED Indicators

System

LED Color Function

PWR Green

Per 10/100Mbps Port

LED Color Function

PoE Green

LNK/ACT Green

Light: Indicates the Switch has

power.

Lights to indicate the port is

providing 51V DC in-line
power to remote PoE PD.

Lights to indicate the link through

that port is successfully
established at 10/100Mbps.

Blinks to indicate that the Switch is

actively sending or receiving
data over that port.

- 7 -

6. Installing the Switch

This part describes how to install your FSD-504HP and
make connections to it. Please read the following topics
and follow the procedures as presented.

This FSD-504HP does not need software

Note

Desktop Installation

To install the FSD-504HP on desktop, simply follow the
following steps:

Step 1: Place the FSD-504HP on desktop near AC

Step 2: Keep enough ventilation space between the

Note

Step 3: Connect your FSD-504HP to network devices.

configuration.

power source for its power adapter.

FSD-504HP and the surrounding objects.

When choosing a location, please keep in
mind the environmental restrictions dis­cussed in Chapter 7 -- Product Specifica­tions.

A. Connect one end of a standard network

cable to the Port-5 of the FSD-504HP that
marks with “Uplink”.

- 2 -

- 4 -

- 6 -

- 8 -

B. Connect the other end of the cable to the

100BASE-TX UTP with PoE

network devices such as routers, Ethernet
switches or NVRs (network video recorders).

Step 4: Connect your FSD-504HP to PoE PD devices.

A. Connect one end of a standard network

cable to port 1 to port 4 10/100Mbps RJ45
PoE+ ports of the FSD-504HP.

B. Connect the other end of the cable to the

802.3at/af powered devices.

Wall-mount Installation

Step 1: Please nd the wall that can mount the

FSD-504HP.

Step 2: Install two screws on the wall.

Step 3: Hang the FSD-504HP on the screws from the

wall.

Step 4: Repeat step 5 of Desktop Installation for

power supply to the FSD-504HP.

Office Building Office Area

Speed Dome

IEEE 802.3af PoE

DC

IEEE 802.3at PoE Splitter

PoE Extender

IEEE 802.3af
PoE IP Camera

Office Building

PoE

PoE

FSD-504HP

Control Room

VoIP Phone

DC

PoE

IEEE 802.3af
PoE IP Camera

Warehouse

Power Line (DC)

100BASE-TX UTP

- 9 -

Before mounting the device to the wall,
please check the location of the electrical

Note

PoE

PoE

outlet and the length of the Ethernet cable.

RJ45
UTP Cable

- 11 -

Cable distance for Switch
If the “DIP Switch Mode” is set to

“Standard”, then the cable distance be-

tween the FSD-504HP and PC/PD devices
should not exceed 100 meters for UTP/

Note

STP cable.

If the “DIP Switch Mode” is set to

“Extend”, then the cable distance be-

tween the FSD-504HP and PC/PD devices
should not exceed 250 meters.

Make sure the wiring is correct

Category 3/4/5 cable can be used in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an un-

Note

shielded twisted-pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.

Step 5: Supply power to the FSD-504HP.

A. Connect one end of the power cable to the

Switch.

B. Connect the power plug of the power cable

to a standard wall outlet.

When the Switch receives power, the power LED should
remain solid Green.

- 10 - - 12 - - 13 - - 14 -

7. Product Specications

Model

Hardware Specications

Hardware Version 2

Network Connector

PoE Inject Port

LED Display

Switch Architecture Store and Forward switch architecture

MAC Address Table

Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64bytes
Maximum Packet Size 1536bytes

Flow Control

Power Requirements DC 51V, 1.25A.
Power Consumption Max. 63 watts, 214 BTU

Dimensions
(W x D x H)

Weight 257g

FSD-504HP

4-Port 10/100Mbps 802.3af/at PoE +
1-Port 10/100Mbps Desktop Switch

5-Port RJ45 for 10/100BASE-TX, auto
MDI/MDIX

4-Port with 802.3af/at PoE injector
function (Port 1 to port 4)

System: Power (Green)
Per PoE port: PoE (Green, port 1 to

port 4)
LNK/ACT (Green, port 1 to port 5)

1K MAC address table with auto
learning function

Back pressure for half-duplex. IEEE

802.3x pause frame for full-duplex

100 x 100 x 26mm

Power over Ethernet

IEEE 802.3af Power over Ethernet/PSE

PoE Standard

IEEE 802.3at Power over Ethernet Plus/
PSE

PoE Power Supply Type End-span + mid-span
Power Pin Assignment 1/2(+), 4/5(+), 3/6(-), 7/8(-)

Per Port 51V DC, 300mA. max. 15.4

PoE Power Output

watts (IEEE 802.3af)
Per Port 51V DC, 600mA. max. 30
watts (IEEE 802.3at)

PoE Power Budget 60 watts
Number of PDs, 7 watts 4

Number of PDs, 15.4
watts

Number of PDs, 30
watts

4

2

Standard Conformance
EMI Safety FCC Class A, CE

Standard Compliance

IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at

Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
Power over Ethernet Plus

Environment
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C

Operating Humidity

Storage Humidity

5 ~ 95%, relative humidity, non­condensing

5 ~ 95%, relative humidity, non­condensing

8. Customer Support

Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website

rst to check if it could solve your issue. If you need

more support information, please contact PLANET switch
support team.

PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1

Switch support team mail address:
[e-mail]

Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.