PLANET CAM-IVP55V User Manual
– 1 – – 2 –
– 3 – – 4 –
1. Please read before using
1. Please do not directly touch the sensor element. If necessary, use a soft cloth moistened with alcohol to wipe off
any dust.
2. Please be extra careful not to shake the camera.
3. Please avoid places where there is direct sunlight.
4. When the camera is not in use, keep the lens or the lens
cap attached to protect the sensor.
5. Don’t attempt to service this unit yourself unless you are
authorized to do so. This may exposure you to dangerous
voltage or other hazards. Refer all servicing to qualied
personnel only.
6. Please don’t use the camera under the following abomi
nable environments. Temperature is lower than -10
degrees Centigrade, or is higher than +50 degrees Centigrade.
2. Package Contents
• 1 x CAM-IVP55V
• 1 x Quick Installation Guide
• 1 x Wrench
• 4 x Screw
3. Overview
Power Input
Video Output
Connector Denition
Connector Description
Power Input Connect to a DC 12V power adapter.
Video Output BNC connector for analog video output.
4. Product Specication
General
Image pick-up device 1/3” SONY Super HAD (Hi-Res.) CCD
Effective Pixels
NT: 768(H) x 494(V)
PA: 752(H) x 582(V)
Horizontal Resolution 550 TVL
Lens 3.7~12 mm, Vari-Focal with DC drive Auto-Iris lens
Min. Illuminator 0.3 Lux / F2.0 ; 0 Lux ( IR on )
Auto Electronic Shutter
NTSC: 1/60s~1/100,000s
PAL: 1/50s~1/110,000s
S/N Ratio More than 48 dB
Gamma Characteristic
0.45
White Balance
Auto
Gain Control Auto
Flickless Mode On / Off ( NT:1/100, PA: 1/120 )
Back Light Comp. On / Off
Synchronous System
Internal
Video Output Composite 1.0 Vp-p, 75 ohm
View Angle H: 21~68 Degree V: 16 -54 Degree
Back Light Comp. On / Off
IR LED 24 pieces
IR Wavelength 850 nm
IR Distance 20~25 meters
Vandal Resistant 10 pounds
Water Resistant
IP-66
Environment
Power Requirement
DC 12V
IR on: 400mA max. / IR off: 200mA max.
Dimensions 145 x 110 mm (Φ x H)
Weight 1.03 kg
Operating Temperature -10 ~ 50 Degree C
5. Physical Installation
1. Use the provided wrench to loose the tamper-resistant
housing cover with screws still attached on the cover.
Note
During the installation, please take care and
avoid crash. That may cause people hurt and
this device damage
2. Set the mounting base onto the wall or ceiling and
center it over the mounting hole, using the supplied four
retaining screws to secure the main body.
3. Set proper image by moving the camera module and set
the focus by turning the lens to the left or right direction.
– 5 – – 6 –
4. When the camera focus adjustment has been completed,
use the provided wrench to fasten the tamper-resistant
housing to the main body.
5. Besides the waterproof connector, when using the side
conduit cabling, it is suggested to cover the cables using
metal covers (to prevent external damage and for waterproof prevention), and wined the waterproof adhesive
tape onto the metal cover before installation.
6. Connect the video output to the monitor or other video
device through a 75 Ohm type coaxial cable and the DCJack to the power source.
Note
Please make sure the power output voltage is
DC 12V (max. ±10%). We suggest using a DC
12V switching power adapter which can provide
a stable power output.
6. DIP Switch Setting
• Flickerless Function
Set switch-OFF/ F.L. to Flicker to enable ickerless func
-
tion, in this mode, the switch-AES/ OFF is auto disabled.
• AGC-Hi/ AGC-Lo Function
Adjust the switch to AGC indicates AGC-Hi and OFF indi-
cates AGC-Low. AGC-Hi mode--The maximum AGC gain is
approximately 26dB. AGC-Lo mode--The maximum AGC
gain is approximately 16dB.
• Auto Iris Function
When using an auto iris lens, the switch-AES/ OFF should
be in the OFF position to disable the AES function. Adjust
VR to the proper level.
• BLC Function
Set switch-OFF/ BLC to BLC to enable Back Light
Compensation (BLC) function.
Loading...