PLANET CAM-IVP52V User Manual

Overview

Note

Power Input

Video Output

Connector Denition

Connector Description

Power Input Connect to a DC 12V power adapter.

Video Output BNC connector for analog video output.

Physical Installation

1. Use the provided wrench to loose the tamper-resistant housing cover with screws still attached on the cover.

During the installation, please take care and avoid crash. That may cause people hurt and this device damage

2. Set the mounting base onto the wall or ceiling and center it over the mounting hole, using the supplied four retaining screws to secure the main body.

– 3 – – 4 –

3. Set proper image by moving the camera module and set the focus by turning the lens to the left or right direction.

4. When the camera focus adjustment has been completed, use the provided wrench to fasten the tamper-resistant housing to the main body.

5. Besides the waterproof connector, when using the side conduit cabling, it is suggested to cover the cables using metal covers (to prevent external damage and for waterproof prevention), and wined the waterproof adhesive tape onto the metal cover before installation.

DIP Switch Setting

• Flickerless Function

 Setswitch-OFF/F.L.toFlickerto enable ickerlessfunc-

tion, in this mode, the switch-AES/ OFF is auto disabled.

• AGC-Hi/ AGC-Lo Function

Adjust the switch to AGC indicates AGC-Hi and OFF indi

cates AGC-Low. AGC-Hi mode--The maximum AGC gain is approximately 26dB. AGC-Lo mode--The maximum AGC gain is approximately 16dB.

• Auto Iris Function

When using an auto iris lens, the switch-AES/ OFF should

be in the OFF position to disable the AES function. Adjust VR to the proper level.

• BLC Function

Set switch-OFF / BLC to BLC to enable Back Light

Compensation (BLC) function.

6. Connect the video output to the monitor or other video device through a 75 Ohm type coaxial cable and the DCJack to the power source.

Please make sure the power output voltage is DC 12V (max. ±10%). We suggest using a DC 12V switching power adapter which can provide a stable power output.

– 5 – – 6 –

Please read before using

Product Specication

1. Please do not directly touch the sensor element. If necessary, use a soft cloth moistened with alcohol to wipe off any dust.

2. Please be extra careful not to shake the camera.

3. Please avoid places where there is direct sunlight.

4. When the camera is not in use, keep the lens or the lens cap attached to protect the sensor.

5. Don’t attempt to service this unit yourself unless you are authorized to do so. This may exposure you to dangerous

voltage or other hazards. Refer all servicing to qualied

personnel only.

6. Please don’t use the camera under the following abomi nable environments. Temperature is lower than -10 degrees Centigrade, or is higher than +50 degrees Centigrade.

Package Contents

• 1 x CAM-IVP52V

• 1 x Quick Installation Guide

• 1 x Waterproof Connector

• 1 x Wrench

• 4 x Screw

– 1 – – 2 –

General

Image pick-up device 1/3” SONY Super HAD (Hi-Res.) CCD

Effective Pixels

Horizontal Resolution 520 TVL

Lens

Min. Illuminator 0.3 Lux / F2.0; 0 Lux (IR on) Auto Electronic

Shutter S/N Ratio More than 48 dB Gamma Characteristic 0.45 White Balance Automatically (2400~9600°K)

Auto Gain Control High / Low Flickless Mode On / Off (NT: 1/100, PA: 1/120) Back Light Comp. On / Off Synchronous System Internal Video Output Composite 1.0 Vp-p, 75 ohm IR LED 24 pieces IR Wavelength 850 nm IR Distance 25 meters Vandal Resistant 10 pounds Water Resistant IP-66

NT: 768(H) x 494(V) PA: 752(H) x 582(V)

3.7~12 mm, F1.6~3.0 Vari-Focal with DC drive Auto Iris lens

NT: 1/60~1/100000 sec PA: 1/50~1/110000 sec

Environment

Power Requirement

Dimensions 145x110mm(ΦxH) Weight 1.01 kg Operating Temperature -10 ~ 50 Degree C

DC 12V IR on: 400mA max. / IR off: 200mA max.