PLANET CAM-BX42 User Manual
CCD Box Camera – CAM-BX42
Packet Content
z
1 x CAM-BX42
z
1 x L-type Wrench
z
1 x Quick Installation Guide
Features
z
1/3” SONY CCD sensor
z
Horizontal resolution with 420TVL
z
Min. illumination 0.05 lux @ F1.2
z
Supports both C and CS lens
z
Support both DC-drive and Video-drive auto iris lens
z
Employs Digital Signal Processor (DSP) chip-set for image control
z
Pixel number: NTSC=270K / PAL=320K (Normal Resolution)
z
High sensitivity, low smear, high anti-blooming and high S/N ratio
z
Powerful functions: Auto Electronic Shutter (AES), Auto Iris Control(AIC), Auto Gain Control (AGC), Auto White
Balance (AWB), Back Light Compensation (BLC)
z
Supports Auto Iris Lens: both Video-Drive & DC-Drive lens
z
Built-in Anti-Aliasing and IR-cut optical filter
Installation
1. Connect a suitable lens to CAM-BX42. If it is an auto-iris lens, please also connect the auto-iris connector
and select DC or Video drive with the control switch on rear panel. For DC drive, you may adjust the DC
LEVEL screw to make this lens be drive properly.
2. Please fix the CAM-BX42 to a suitable location with a stand.
3. Adjust the camera to the correct direction.
4. Connect Video Output connector to your DVR or CCTV system.
5. Connect a DC 12V power adapter to the Power Input connector.
Note: Before connect power adapter to camera, please make sure the power output voltage is DC 12V
(max. ±10%). If you can not sure this part, we will suggest to use a DC 12V Switching power adapter. It can
provide stably power output.
Connector Definition
Connector Description
Auto Iris Connector
Connect to DC-drive / Video-drive auto
iris lens
Power IN Connect to DC 12V power adapter.
BLC(ON/OFF): Enable / Disable the back
light compensation control
Control Switch
AE/AI: Switch to AE / AI
DC/Video: Switch to DC-drive /
Video-drive auto iris lens control
VR Adjustment level
for DC Drive Lens
Use to adjust video output level of
DC-drive auto iris lens.
Video Output BNC connector for analog video output
Auto Iris function
When use the Auto Iris Lens, the control switch should be in position AI to disable AES function. Before plug the enclosed
miniature 4 pins to IRIS connector, please check the type of Auto Iris Lens, and also the compatibility on the polarities.
z
If the Auto Iris Lens is DC DRIVE, the control switch should be in position DC DRIVE. Adjust the LEVEL with the
VR to proper.
z
If the Auto Iris Lens is VIDEO DRIVE, the control switch should be in VIDEO DRIVE position.
When using the Manual Iris Lens the switch is depend on application environment. Set control switch to BLC to enable BLC
function.
.
Pin1
Pin2 Drive+ N.C
Pin3 Damp+ IRIS
Pin4 Damp- GND
DC” VIDEO
Drive- Volt +
Specification
Image pick-up device SONY 1/3“ CCD Normal Resolution
Effective Picture Elements NTSC: 510*492, PAL: 500*582 (H*V)
Horizontal Resolution 420 TVL
Minimum Illumination 0.05 LUX @ F1.2
Auto Electronic Shutter
Signal To Noise Ratio More than 50dB (AGC Off)
Auto Iris Control Video-Drive Lens & DC-Drive Lens both supported
Gamma Characteristic 0.45
Lens Mount C or CS mount adjustable
Gain Control Automatically
White Balance Automatically (2500K~9500K)
Back Light Compensation ON/OFF Switch-able
Synchronous System Negative sync. Internal
ON : NTSC:1/60s~1/100,000s, PAL:1/50s~1/110,000s
OFF :NTSC:1/60s, PAL:1/50s
Video Output 1 Vp-p Composite Video / 75 Ohms. BNC connector.
Power Request
Power Consumption
Operating Temp.
DC12V/ 400mA , 50/60 Hz
3.5W
-10℃ to 50℃ (14℉ to 122℉)
Part no.:2011-L00110-002
Loading...