Planar SA2311W User Manual

SA2311W

3D Ready Monitor

www.planar3d.com

Contents

Preface

Installation

Display Controls

Technical Information

Troubleshooting

.....................................................................................................................1

Warning.............................................................................................................................................................................1

Safety Precaution.......... ................................................................................................................................................3

................................................................................................................4

Introduction ............................................................................................................................................................... ....4

Features....................................................................................................................................................................... ....4

Unpacking .......................................................................................................................................................................5

Preparing The Monitor For Wall-Mounting .................................................................................................. ....6

Screen Position Adjustment .....................................................................................................................................8

Connecting Cables.......................................................................................................................................................9

Settings for Stereoscopic 3D Use............................................................................... .................................. .....10

....................................................................................................12

Front Panel Controls...................................................................................................................................................12

Lock Function...................................................................................................................................................... ........13

OSD Operation .............................................................................................................................................................14

...........................................................................................16

Specifications..............................................................................................................................................................16

Supported Timing......................................................................................................................................................17

....................................................................................................18

Product Registration and Technical Support

....................................................19

Preface

The information contained in this document is subject to change without notice. This document contains
proprietary information that is protected by copyright. All rights are reserved. No part of this document
may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any
means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission.
Windows is registered trademark of Microsoft Inc. Other brand or product names are trademarks of their
respective holders.

FCC Statement Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instruction, may cause harmful interference
to radio communications.
installation. If this equipment does
be determined by turning the equipment

interference by one or more of the following measures:

• Reposition or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced monitor technician for help.

Warning

Use only shielded signal cables to connect I/O devices to this equipment. You are cautioned that
changes or modifications not expressly approved by the party responsible for compliance could void

your authority to operate the equipment.

This device complies with part 15 FCC Rules. Operation is subject to the following two conditions(1) This
device may not cause harmful interference. (2) This device must accept any interference received,
including interference that may cause undesired operation.

However, there is no guarantee that interference will not

television reception, which can cause harmful interference to radio or

off and on, the user is enco

uraged to try to correct the

occur in a particular

1

Canadian DOC Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.

Cet appareil numérique de la classe B repecte toutes les exigences du Règlement sur le

matériel

Important Recycle Instruction:

Lamp(s) inside this product contain mercury. This product may contain other

electronic waste that can be hazardous if not disposed of properly. Recycle or dispose
in accordance with local, state, or federal Laws. For more information, contact the
Electronic Industries Alliance at WWW.EIAE.ORG
check WWW.LAMPRECYCLE.ORG.

Contains Mercury, Dispose of Properly

. For lamp specific disposal information

2

Safety Precautions

Avoid placing the monitor, or any other heavy object, on the power cord to prevent it from fire or

electrical shock.

Do not expose the monitor to rain, excessive moisture, or dust to avoid fire or shock hazard.

Do not cover the slots or openings of the monitor for proper heat dissipation.

Always put the monitor in a place where there is adequate ventilation.

For optimal viewing avoid placing the monitor against a bright background or where sunlight or other

light sources may reflect on the face of the monitor. Place the monitor just below eye level.

Handle with care when transporting the monitor.

Do not touch the screen except when lightly cleaning it with a soft cloth.

For some individuals, prolonged use of a stereoscopic monitor may cause discomfort. Take a break

from stereo viewing if you sense eye fatigue or other symptoms. Individuals who are unaccustomed

to using stereoscopic 3D monitors may require a period of adaptation.

Cleaning Your Monitor

Please carefully follow the guidelines below when cleaning the monitor.

Always unplug the monitor before cleaning.

Use a soft cloth to wipe the screen and cabinet front and sides.

About Power Cable

Check first to make sure that the power cord you use is the correct type required for your area.

This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V

AC voltage area. No user-adjustment is required.

Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet.

For unit using at 120 V AC: Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V.

For unit using at 220/240 V AC (outside of U.S.): Use a Cord Set consisting of H05VV-F cord and plug

rated 10 A, 250 V. The cord set should have the appropriate safety　approvals for the country In which

the equipment will be installed.

3

Installation

Introduction

Congratulations on your purchase of the SA2311W high performance LCD monitor. This 23-inch wide­format monitor is 3D ready with full HD resolution for both professional and entertainment use.

Features

* 23 “ TFT Color LCD monitor

* 16:9 Widescreen

* Full HD 3D functionality

*　NVIDIA 3D vision certified

* Recommended resolution: 1920 x 1080 @ 60Hz

* Direct analog signal input

* Direct digital signal input

* Direct HDMI signal input

* Auto adjustment function

* OSD user control

* Kensington security slot

* 100mm VESA mount

* Compact, space saving, sleek cabinet design

* Height adjustable stand with tilt and swivel

TM

4

Unpacking

Please check that the following items are present when you unpack the box.
We recommend you save the packaging　for future use.

LCD Monitor

SA2311W

3D Monitor

User Guide

AC Power Cord

15-pin D-Sub Cable

5

DVI Cable