Page 1
PT3285PW
T ouch Screen Edge-lit LED LCD Monitor
USER’S GUIDE
www.planar.com
Page 2
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be reproduced,translated to another language
or stored in a retrieval system, or transmitted by any means, electronic, mechanical,
photocopying, recording, or otherwise, without prior written permission. Windows is a registered
trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective
holders.
The test results show that this device meets the FCC rules. Those limits are set to protect
residential areas from the devices with harmful emission. This device will produce, use and
radiate radio frequency energy. In addition, failure to follow the user’s manual to install or use
this device might produce harmful interference with radio communication. Not withstanding
the foregoing, it does not guarantee that this type of harmful interference does not occur in
some special installations. The interference caused by this device to the reception of radio
or television signals may be verifi ed by turning it on and off. Any changes or modifi cations to
this TFT edge-lit LED LCD would void the user’s authority to operate this device.
For more information on how to recycle your product, please visit
WWW.PLANARSYSTEMS.COM/GREEN.
Page 3
Table of Contents
Usage Notice
Precautions............................................................................................................................. 1
Introduction
About PT3285PW ................................................................................................................... 2
Touch Screen for PT3285PW ................................................................................................. 2
Package Overview ...................................................................................................... 3
Installation
Product Overview ........................................................................................................ 4
Front View .............................................................................................................. 4
Bottom View ........................................................................................................... 4
VESA Mount for Your Monitor ...................................................................................... 5
Start Your Installation .................................................................................................. 6
Connecting the Display (Figure 8.1) ............................................................................. 7
(Figure 8.1) ............................................................................................................. 8
User Controls
Rear Panel Controls .................................................................................................... 9
How to Use the OSD Menus .......................................................................................10
On-Screen Display Menus ..........................................................................................11
Appendix
Troubleshooting ..........................................................................................................12
Warning Signal ...........................................................................................................13
No Signal ...............................................................................................................13
Going to Sleep........................................................................................................13
Out of Range ..........................................................................................................13
Product Dimensions ...................................................................................................14
Compatibility Modes ...................................................................................................15
Touch Screen Driver Installation .................................................................................16
PT3285PW Calibration Tool Install ..........................................................................16
Page 4
Usage Notice
! Warning - To prevent the risk o
f fi
re or shock hazards, do not expose
this product to rain or moisture.
! Warning - Please do not open or disassemble the product as this ma
y
cause elec
tric shock.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to
maximize the life of your unit.
Do:
• Turn off the product before cleaning.
• Touch screen surface may be cleaned using a soft clean cloth moistened with mild
window glass commercial cleaners or 50/50 mixture of water and isopropylalcohol.
• Use a soft cloth moistened with mild detergent to clean the display housing.
• Disconnect the power plug from AC outlet if the product is not going to be used for
an extended period of time.
Don’t:
• Do not touch the Display screen surface with sharp or hard objects.
• Do not use abrasive cleaners, waxes or solvents for your cleaning.
• Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic fi eld.
- In direct sunlight.
1
Page 5
Introduction
About PT3285PW
The PT3285PW is a 31.5" fl at panel screen with an active matrix, thin-fi lm transistor (TFT)
edge-lit LED LCD.
Features include:
• Direct Analog signal input
• Direct Digital signal input
• Active matrix TFT edge-lit LED LCD technology
• 1920 x 1080 resolution
• 31.5" viewable display area - 16:9 aspect ratio
• 31.47 ~ 67.5 KHz horizontal scan
• 47 ~ 63 Hz high refresh rate
• 0.36375mm x 0.36375mm pixel pitch
• Auto adjustment function
• Multilingual OSD user control
• 400mm x 200mm VESA mount
• Projected Capactive touch screen with USB controller
• Audio - 8W x 2
Touch Screen for PT3285PW
• Project Capacitive touch screen for fi nger input only
• Surface: Glare treatment
• Interface: USB controller
• Transmittance: 90%±5%
• HID: Microsoft Windows® 7
2
Page 6
Package Overview
3
Display Power Cord
USB Cable (A to B) Audio-in Cable
VGA Signal Cable
DVI-D Cable
Touch Screen Driver
Installation CD-ROM
Landing StripUser’s Guide
xxxxxxxxx
/
xxxxxxxxx
xxxxxxxxx
USER’S GUIDE
www.planartouch.com
Cable Cover Screw
Page 7
Installation
Product Overview
• Front View
• Bottom View
4
AC IN
AUDIO OUT
Remote Key
COM OUT
VGA IN
DVI IN
AUDIO IN
USB
COM IN
Page 8
VESA Mount for Your Monitor
This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface
standard which defi nes a physical mounting interface for fl at panel monitors, and
corresponding with the standards of fl at panel monitor mounting devices, such as wall and
table arms. The VESA mounting interface is located on the back of your monitor.
To mount the monitor on a UL certifi ed swing arm or other mounting fi xture, follow the
instructions included with the mounting fi xture to be used.
!
Warning!
Please select the proper screws!
The distance between the back cover surface and the bottom of the screw hole
is 8 mm. Please use four M6 screws diameter with proper length to mount your
monitor.
Please note: the optional mount must be able to support at least 44 lbs (20Kg).
5
M6
400.0 mm
200.0 mm144.2 mm
Page 9
Start Your Installation
Please follow these instructions so that you can hook up the cables to associated connectors.
1. Lay the display fl at on an even surface and take off cable cover as seen in thestep 1 diagram.
2. Connect the cables to the appropriate connectors as seen in the step 2 diagram.
3. Take screw from the accessory box, and put all cables under the cover lip, then use a
Philips Head screw driver, insert the screw (CBM M3x6) into cable cover and monitor as
seen in the step 3-1 or step 3-2 diagram either.
Step 1
COM-InVGA
COM-OutDVI
USBPower
Audio-Out
Audio-In
Step 2
Step 3-1
Step 3-2
6
Page 10
7
Connecting the Display (Figure 8.1)
To setup this display, please refer to the following fi gure and procedures.
1. Be sure all equipment is turned off.
2. Connect the AC power cord to the power connector on the monitor and the other end
into an electrical outlet (8.1).
3. Connect the D-SUB or DVI cable from the display’s VGA input connector to the D-SUB
or DVI connector of your host computer and tighten the screws (8.1).
4. Connect the Audio-In cable from the audio input port of your display to the Audio-out port
of your computer (8.1).
5. Connect the USB cable from USB port of your display to USB port of your computer (8.1).
6. Once the touch screen is confi gured, the monitor is ready for use.
!
Notice!
To ensure the display works well with your computer, please confi gure the display
mode of your graphics card to make it less than or equal to 1920 x 1080 resolution
and make sure the timing of the display mode is compatible with the display.
We have listed the compatible “Video Modes” of your display in the appendix
(on page 15) for your reference.
Page 11
8
(Figure 8.1)
Controlling the PT3285PW monitor via RS-232 C Remote Control (Optional)
The PT3285PW monitor can be controlled by connecting a PC with a RS-232C terminal
diagramed below:
Note:
Two COM Ports are reserved for this option.
Before using the remote control function, design a custom fi rmware based on your own
application program and communication protocol. Use null modem cable to enable it.
COM In COM Out
COM In
Page 12
9
User Controls
Rear Panel Controls
OSD
Key
Menu off status Menu on status
Menu appear Menu disappear / return to main item
Brightness Main item select up / Adjust up
Mute Main item select down / Adjust down
Auto Adjust Select sub-item function
Power On / Off
Icon Key Name
Menu
Up
Down
Select
Power
Page 13
10
How to Use the OSD Menus
1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button
to select among the six functions in the main menu.
2. Choose the adjustment items by pressing the “Select” button.
3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.
4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD.
5. The OSD menu will automatically close, if you have left it idle for a pre-set time.
6. To Lock the OSD / Power menu buttons, please follow the instructions below.
(Please note: the monitor has to be turned ON with a valid signal pre-set)
(a.) Press “Menu” key , the OSD menu pops upon display.
(b.) Press and hold the “Menu” key again with the OSD menu on the screen, the OSD
menu will disappear. Then press the “Power” key 1 time while the menu key is still
being pressed. The “Lock/Unlock” menu will appear for 3 seconds.
(c.) Use the “Select” key to select OSD or Power setting then set at “Lock” by pushing the
“UP” or “Down” button.
(d.) When the “UP” or “Down” button is released, the previous setting will be saved and
exit the “Lock/Unlock” menu automatically.
7. To Unlock the OSD / Power menu buttons, please follow the instructions below.
(Please note: the monitor has to be turned ON with a valid signal pre-set)
(a.) Press and hold the “Menu” key then press the “Power” key simultaneously, the “Lock/
Unlock” menu will appear for 3 seconds.
(b.) Use the “Select” key to select OSD or Power setting then set at “Unlock” by pushing the
“UP” or “Down” button.
(c.) When the “UP” or “Down” button is released, the previous setting will be saved and exit
the “Lock/Unlock” menu automatically.
Please note:
a. When the OSD Lock function is selected, this indicates that all the buttons except “power”
button are now disabled.
b. When the Power Lock function is selected, this indicates that the power key is disabled;
user can not to turn off the monitor by “Power” key.
Icon Key Name
Menu
Up
Down
Select
Power
Page 14
11
On-Screen Display Menus
Main OSD Menu:
ITEM CONTENT
Contrast The monitor luminance level control.
Brightness The monitor backlight level control.
Auto Adjust Fine-tune the image to full screen automatically.
Left/Right Moving screen image horizontal position to left or right.
Up/Down Moving screen image vertical position to up or down.
Horizontal size The screen image horizontal dot clock adjustment.
Fine The screen image pixel phase adjustment.
OSD Left/Right Moving OSD menu horizontal position to left or right.
OSD Up/Down Moving OSD menu vertical position to up or down.
OSD Time out OSD auto-disappear time selection.
OSD Language
OSD menu language selection. ( English, French, Japanese, Deutsch,
Spanish, Italian, Traditional Chinese and Simplifi ed Chinese)
Factory Reset Factory default value restored.
RGB Color temperature selection. (9300K, 6500K, 5500K, 7500K, User)
Volume Audio volume adjustment.
Mute Audio On/Off control.
Page 15
12
Appendix
Troubleshooting
If you are experiencing trouble with the display, refer to the following. If the problem persists,
please contact your local dealer or our service center.
Problem: No image appears on screen.
► Check that all the I/O and power connectors are correctly and well connected
as described in the “Installation” section.
► Make sure the pins of the connectors are not crooked or broken.
Problem: Partial Image or incorrectly displayed image.
► Check to see if the resolution of your computer is higher than that of the display.
► Reconfi gure the resolution of your computer to make it less than or equal to
1920 x 1080.
Problem: Image has vertical fl ickering line bars.
► Use “Fine” to make an adjustment.
► Check and reconfi gure the display mode of the vertical refresh rate of your graphic
card to make it compatible with the display.
Problem: Image is unstable and fl ickering
► Use “Fine” to make an adjustment.
Problem: Image is scrolling
► Check and make sure the VGA signal cable (or adapter) is securely connected.
► Check and reconfi gure the display mode of the vertical refresh rate of your
graphics card to make it compatible with the display.
Problem: Vague image (characters and graphics)
► Use “Fine” to make an adjustment. If this problem still exists, use “Horizontal size”
to make an adjustment.
Problem: Touch no function (for Microsoft Windows® 7 only)
► Microsoft Windows® 7 operating system requires 15 seconds to recognize the
PT3285PW after connecting the USB cable and power cable.
Page 16
Warning Signal
If you see warning messages on your screen, this means that the display cannot receive a
clean signal from the computer graphics card.
Below are the three kinds of Warning Signal. Please check the cable connections or contact
your local dealer or our service center for more information.
No Signal
This message means that the display has been powered on but it cannot receive any signal
from the computer graphics card. Check all the power switches, power cables, and VGA/DVI
signal cable.
Going to Sleep
The display is under the power saving mode. In addition, the display will enter power saving
mode when experiencing a sudden signal disconnecting problem.
The monitor can be activated by pressing any keyboard, triggering the mouse or touching
the screen.
Out of Range
This message means that the signal of the computer graphic card is not compatible with
the display. When the signal is not included in the “Video Modes” list we have listed in the
Appendices of this manual, the monitor will display this message.
13
Page 17
Product Dimensions
14
Side View
Back View
Front View
786.1mm
4- R13
480.7mm
69mm
590.0mm
98.1mm 98.1mm
400.0mm
200.0mm144.1mm
Page 18
Compatibility Modes
Mode Resolution H-Frequency(khz) V-Frequency(hz)
IBM VGA 640X480 31.47 60
VESA SVGA 800X600 35.16 56
VESA SVGA 800X600 37.88 60
VESA XGA 1024X768 48.36 60
VESA SXGA 1280X1024 64.00 60
VESA SXGA 1280X960 60.00 60
WXGA+ 1440X900 56.00 60
WSXGA+ 1680X1050 65.20 60
VESA WXGA 1280X768 47.776 60
VESA WXGA 1280X720 44.77 60
VESA WXGA 1366X768 47.71 60
WSXGA+ 1920X1080 67.50 60
15
Page 19
Touch Screen Driver Installation
The PT3285PW Series is available with USB connection.
Please Note:
1. The PT3285PW is Microsoft Windows® HID (Human Interface Device) compatible
if you use the USB touch screen interface. No additional software driver is required for
general operation of the touch screen.
2.
Microsoft Windows® 7 operating system requires 15 seconds to recognize the PT3285PW
after connecting the USB cable and power cable.
PT3285PW Calibration Tool Install:
PLEASE NOTE!
1. Calibration is required when using PT3285PW touch display for the fi rst time or
switching from monitor to PC. Do not touch the screen during calibration tool
execution process.
2. The PT3285PW touch display is only compatible with Microsoft Windows® 7.
To use the Calibration Tool, follow the instructions.
1. Open the CD-ROM
2. Select size - 32”
3. Select model - PT3285PW
4. Run or save calibration
5. Please do not touch the screen during calibration tool execution process
16
!
Page 20
Planar Systems, Inc.
Customer Service
24x7 Online Technical Support: http://www.planar.com/support
1195 NW Compton Drive
Beaverton, OR 97006-1992
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States.
Hours: 24 hours a day, 7 days a week
© 2013 Planar Systems, Inc. 1/13 Planar is a registered trademark of Planar Systems, Inc.
Other brands and names are the property of their respective owners.
Technical information in this document is subject to change without notice.
020-1170-01A
8204321A0103
Loading...